C1581-00-FRONT/REAR TIRE PRESSURE SENSOR LOCATION UNDETERMINED
For a complete wiring diagram, refer to the Wiring Information.
| NOTE: |
Check for and remove any non-FCC compliant components before beginning this diagnostic procedure. |
Theory of Operation
The vehicle Tire Pressure Monitoring (TPM) Sensor locate process occurs after the vehicle remains stationary for 20 minutes. The Tire Pressure Monitoring (TPM) Module will determine the Tire Pressure Monitoring (TPM) Sensor positions. The TPM Module measures the signal strength of each TPM sensor and determines if the are in the front or rear.
-
When Monitored:
During vehicle TPM Sensor locate process.
-
Set Condition:
Must fail multiple vehicle TPM sensor locate processes if localization fails due to Front/Rear fail or if the TPM module is new and has never attempted localization.
Possible Causes |
|---|
| NON-FCC COMPLIANT COMPONENTS |
| TIRE PRESSURE MONITORING (TPM) MODULE HARNESS |
| INCORRECT TIRE PRESSURE MONITORING (TPM) MODULE INSTALLATION |
| TIRE PRESSURE MONITORING (TPM) MODULE |
| NOTE: | The vehicle must remain stationary for 20 minutes before proceeding with this diagnostic procedure. |
| 1. | Turn the ignition on. |
| 2. | With the scan tool, read and record TPM Module DTCs. |
| 3. | Test drive the vehicle at a speed greater than 24 km/h (15 mph) for 10 minutes in order to receive TPM Sensor data and allow for the system to update. |
| 4. | With the scan tool, erase stored TPM Module DTCs. |
| 5. | With the scan tool, select View DTCs in the TPM Module. |
Is the DTC status Active at this time?
Yes
- Go To 2
No
- Go To 3
2. TIRE PRESSURE MONITORING (TPM) MODULE INTERFERENCE
| NOTE: | Interference may occur if the TPM Module is installed incorrectly or the TPM harness is not fastened properly to the body. |
| 1. | Turn the ignition off. |
| 2. |
Verify the following: |
- Aftermarket devices are installed or in the vehicle.
- The TPM Module harness is damaged or is routed incorrectly.
- The TPM Module is installed incorrectly.
Are there any of the above conditions present?
Yes
- Repair as necessary.
- Perform the TPM VERIFICATION TEST. (Refer to 28 - DTC-Based Diagnostics/MODULE, Tire Pressure (TPM) - Standard Procedure).
No
- Install a new Tire Pressure Monitoring (TPM) Module in accordance with the Service Information. (Refer to 22 - Tires and Wheels/Tire Pressure Monitoring/MODULE, Tire Pressure Monitoring (TPM) - Removal).
- Perform the TPM VERIFICATION TEST. (Refer to 28 - DTC-Based Diagnostics/MODULE, Tire Pressure (TPM) - Standard Procedure).
3. INTERMITTENT TIRE PRESSURE MONITORING (TPM) SENSOR DTC
| 1. | The conditions necessary to set this DTC are not present at this time. |
| 2. | Perform any Technical Service Bulletins that may apply to this condition. |
| 3. | With the scan tool, clear DTCs in the Tire Pressure Monitoring (TPM) Module. |
| 4. | Test drive the vehicle for a minimum of 20 minutes with vehicle speed greater than 24 km/h (15 mph). |
| 5. | With the scan tool, select View DTCs in the Tire Pressure Monitoring (TPM) Module. |
Does the DTC reset or is the status Active for this DTC?
Yes
- Install a new Tire Pressure Monitoring (TPM) Module in accordance with the Service Information. (Refer to 22 - Tires and Wheels/Tire Pressure Monitoring/MODULE, Tire Pressure Monitoring (TPM) - Removal).
- Perform the TPM VERIFICATION TEST. (Refer to 28 - DTC-Based Diagnostics/MODULE, Tire Pressure (TPM) - Standard Procedure).
No
- Test complete.
- Perform the TPM VERIFICATION TEST. (Refer to 28 - DTC-Based Diagnostics/MODULE, Tire Pressure (TPM) - Standard Procedure).