B140F-REAR RIGHT AUDIO SPEAKER OUTPUT CIRCUIT OPEN - BASE
 |
For a complete wiring diagram, refer to the Wiring Information.
| NOTE: |
There are two versions of the B140F DTC test. In order to select the proper test you must know if the vehicle is equipped with an Amplifier. If the vehicle is equipped with an Amplifier use the B140F-PREMIUM test. If the vehicle is not equipped with an Amplifier use the B140F-BASE test. |
Theory of Operation
The (X206) Right Rear Speaker (+) circuit and the (X296) Right Rear Speaker (-) circuit are outputs of the Radio. The Radio controls and monitors these circuits for a concern.
-
When Monitored:
With the Radio on.
-
Set Condition:
The Radio detects an open condition on the speaker output circuit.
Possible Causes |
|---|
| (X206) RIGHT REAR SPEAKER (+) CIRCUIT OPEN |
| (X296) RIGHT REAR SPEAKER (-) CIRCUIT OPEN |
| RADIO |
| RIGHT REAR SPEAKER |
1. CHECK FOR AN INTERMITTENT CONDITION
| 1. | Turn the ignition on and open one of the front doors. |
| NOTE: | A front door must remain open whenever checking or erasing Radio DTCs. |
| 2. | Using the scan tool, record and erase the Radio DTCs. |
| 3. | Turn the Radio on. |
| 4. | Adjust the speakers to the rear and center. |
| 5. | Using the scan tool, read the active Radio DTCs. |
Does the scan tool read: B140F-REAR RIGHT AUDIO SPEAKER OUTPUT CIRCUIT LOW?
Yes
- Go To 2
No
- Test complete, the condition or conditions that originally set this DTC are not present at this time. Using the wiring diagrams as a guide, check all related splices and connectors for signs of water intrusion, corrosion, pushed out or bent terminals and correct pin tension.
- Perform the BODY VERIFICATION TEST. (Refer to 28 - DTC-Based Diagnostics/MODULE, Totally Integrated Power (TIPM) - Standard Procedure).
2. CHECK THE RIGHT REAR SPEAKER
 |
| 1. | Turn the ignition off. |
| 2. | Disconnect the Right Rear Speaker. |
| 3. | Measure the resistance of the speaker between the two terminals. |
| NOTE: | The graphic shows the connector for reference only. Measure between the speaker terminals. |
Is the resistance above 5.0 Ohms?
Yes
- Replace the Right Rear Speaker in accordance with the Service Information.
- Perform the BODY VERIFICATION TEST. (Refer to 28 - DTC-Based Diagnostics/MODULE, Totally Integrated Power (TIPM) - Standard Procedure).
No
-
Go To 3
3. CHECK THE (X206) RIGHT REAR SPEAKER (+) CIRCUIT FOR AN OPEN
 |
| 1. | Disconnect the Radio C2 harness connector. |
| 2. | Measure the resistance of the (X206) Right Rear Speaker (+) circuit between the Radio C2 connector and the Right Rear Speaker harness connector. |
Is the resistance below 5.0 Ohms?
Yes
- Go To 4
No
- Repair an open in the (X206) Right Rear Speaker (+) circuit.
-
Perform the BODY VERIFICATION TEST. (Refer to 28 - DTC-Based Diagnostics/MODULE, Totally Integrated Power (TIPM)
- Standard Procedure).
4. CHECK THE (X296) RIGHT REAR SPEAKER (-) CIRCUIT FOR AN OPEN
 |
| 1. | Measure the resistance of the (X296) Right Rear Speaker (-) circuit between the Radio C2 connector, and the Right Rear Speaker harness connector. |
Is the resistance below 5.0 Ohms?
Yes
- Replace the Radio in accordance with the Service Information.
- Perform the BODY VERIFICATION TEST. (Refer to 28 - DTC-Based Diagnostics/MODULE, Totally Integrated Power (TIPM) - Standard Procedure).
No
- Repair an open in the (X296) Right Rear Speaker (-) circuit.
-
Perform the BODY VERIFICATION TEST. (Refer to 28 - DTC-Based Diagnostics/MODULE, Totally Integrated Power (TIPM)
- Standard Procedure).