PRINT
ISUZU I-280
MODEL YEAR(S
I-280 2006-2007
KEY T-HARNESS IMMOBILIZER
N/A N/A GM'S (ION TYPE) PASSLOCK 2 ANTI-THEFT SYSTEM, Requires Bypass Module, See NOTE #1
PART COLOR LOCATION DIAGRAM
12 VOLT CONSTANT Connect DIRECTLY to Battery Only!!
STARTER YELLOW/BLACK (-), (Not for Remote Start), NOTE #1 @ PCM, (BLUE PLUG), PIN 48, NOTE #2 14301_1-280_COLORADO-CANYON PASSLOCK 2 BYPA.pdf
STARTER 2 WHITE/BLUE to WHITE, (MUX), NOTE #1 @ IGNITION SWITCH, (PIN 4) or BCM, (GRAY PLUG), PIN A14, NOTE #3
IGNITION 1 WHITE/GREEN to DARK BLUE (+), NOTE #1 @ IGNITION SWITCH, (PIN 3) or BCM, (GRAY PLUG), PIN B8, NOTE #3
IGNITION 2 N/A
IGNITION 3 N/A
ACCESSORY/HEATER BLOWER 1 WHITE/RED to BROWN (+), NOTE #1 @ IGNITION SWITCH, (PIN 1) or BCM, (GRAY PLUG), PIN B7, NOTE #3
ACCESSORY/HEATER BLOWER 2 N/A
KEYSENSE N/A
PARKING LIGHTS ( - ) BROWN/WHITE (-) @ HEADLIGHT SWITCH or BCM, (GRAY PLUG), PIN A7, NOTE #3
PARKING LIGHTS ( + ) BROWN (+) @ BCM, (BLACK PLUG), PIN A48, NOTE #3
POWER LOCK LT. BLUE (-), TYPE B in EITHER KICK PANEL or BCM, (BLACK PLUG), PIN A11, NOE #3
POWER UNLOCK DK. BLUE (-), TYPE B, NOTE #5 in EITHER KICK PANEL, HARNESS to DOOR
LOCK MOTOR WIRE GRAY (+) @ DOOR LOCK Switch in Drivers Door
DOOR TRIGGER NOTE *4 @ BCM, (BLACK PLUG), NOTE #3
DOMELIGHT SUPERVISION WHITE (-) @ BCM, (BLACK PLUG), PIN A46, NOTE #3
TRUNK RELEASE N/A
SLIDING POWER DOOR N/A
HORN GREEN to BLACK (-) @ HORN Switch or BCM, (GRAY PLUG), PIN A25, NOTE #3
TACH Any wire NOT PINK or BLACK, (AC) @ Any IGNITION COIL or FUEL-INJECTOR
WAIT TO START LIGHT N/A
BRAKE LT. BLUE (+) @ BRAKE PEDAL SWITCH
FACTORY ALARM DISARM DISARMS with FACTORY REMOTE ONLY!!
ANTI-THEFT GM'S (ION TYPE) PASSLOCK 2 ANTI-THEFT SYSTEM, Requires Bypass Module, See NOTE #1 @ IGNITION SWITCH HARNESS
NOTES
NOTE #1: The WHITE/BLUE and the WHITE/YELLOW at the IGNITION SWITCH, work as the STARTER/CRANKING wire and also the PASSLOCK 2 wires on this vehicle. The NEW ION TYPE PASSLOCK 2 ANTI-THEFT System, will require (2) relays and a resistor, you will need to measure the resistance to get the proper resistor to make the bypass circuit work on this vehicle, See DIAGRAM...OR YOU MAY USE AN INTERFACE MODULE INSTEAD OF BUILDING CIRCUIT WITH RELAYS AND RESISTORS...... Use a PLXR, PLJX, or an XK06 with PLXR 3.00 firmware. If you use a CANMAX 400 with 400.GM5 0.13 firmware, this will, in addition to remote start, also operate door locks and factory alarm.





NOTE #2: the PCM (Powertrain Control Module) is located on the PASSENGER SIDE FIREWALL under the HOOD.







NOTE #3: the BCM (Body Control Module) is located in the PASSENGER KICK PANEL.





NOTE #4: This vehicle has (4) DOOR TRIGGER wires the GRAY/BLACK (-) is used for the DRIVERS DOOR, Pin A32, the PASSENGER DOOR is a LIGHT GREEN/BLACK (-) Pin A38, the DRIVERS REAR DOOR is a LIGHT BLUE/BLACK (-) Pin A39 and the PASSENGERS REAR DOOR is a BLACK/WHITE (-) Pin A39 all are located at the BCM's BLACK Plug. When connecting to an ALARM SYSTEM use all 4 DOOR TRIGGER wires and DIODE ISOLATE.





NOTE #5: to UNLOCK just the DRIVERS DOOR, use the WHITE (-) at the BCM, (BLACK PUG), PIN A12.
LINK 1 LINK TEXT 1 LINK 2 LINK TEXT 2