DTC Troubleshooting: P0705 (5-2) (A/T)
DTC Troubleshooting: P0705 (5-2)
| DTC P0705: | Short in Transmission Range Switch Circuit (Multiple Shift-position Input) |
NOTE:
- Record all freeze data and review General Troubleshooting Information before you troubleshoot.
- This code is caused by an electrical circuit problem and cannot be caused by a mechanical problem in the transmission.
| 1. | Clear the DTC in CLEAR MENU with the Honda PGM Tester or HDS. |
| 2. | Move the shift lever to each position slowly, and check the OBD STATUS in DTCs MENU for a pass/fail test of code P0705. Did the result fail? YES - Go to 3. NO - Intermittent failure, the system is OK at this time. If the tester indicates NOT COMPLETE, return to step 1 and recheck.n |
| 3. | Inspect the transmission range switch. Is the switch OK? YES - Go to 4. NO - Replace the transmission range switch. Recheck for a pass/fail test of code P0705 by performing step 1 and 2 after replacing the switch. If the test result is failed, recheck the transmission range switch.n |
| 4. | Shift to all positions other than [P]. |
| 5. | Measure the voltage between PCM connector terminals D6 and A8 or A9. PCM CONNECTORSLG1 (BRN/YEL)LG2 (BRN/YEL)ATP P(BLU/RED)Wire side of female terminalsA (31P)D (17P) Is there battery voltage? YES - Go to 6. NO - Check for a short in the wire between PCM connector terminal D6 and the transmission range switch, and check for an open in the wires between ground G101 and PCM connector terminals A8 and A9. If the wires are OK, update the PCM if it does not have the latest software, or substitute a known-good PCM, then recheck. If the symptom/indication goes away with a known-good PCM, replace the original PCM.n |
| 6. | Shift to all positions other than [R]. |
| 7. | Measure the voltage between PCM connector terminals D5 and A8 or A9. PCM CONNECTORSLG1 (BRN/YEL)LG2 (BRN/YEL)ATP P (WHT)Wire side of female terminalsA (31P)D (17P)Is there battery voltage? YES - Go to 8. NO - Check for a short in the wire between PCM connector terminal D5 and the transmission range switch. If the wire is OK, update the PCM if it does not have the latest software, or substitute a known-good PCM, then recheck. If the symptom/indication goes away with a known-good PCM, replace the original PCM.n |
| 8. | Measure the voltage between PCM connector terminals C12 and A8 or A9. PCM CONNECTORSLG1 (BRN/YEL)LG2 (BRN/YEL)ATP RVS(RED/WHT)Wire side of female terminalsA (31P)C (22P) Is there battery voltage? YES - Go to 9. NO - Check for a short in the wire between PCM connector terminal C12 and the transmission range switch. If the wire is OK, update the PCM if it does not have the latest software, or substitute a known-good PCM, then recheck. If the symptom/indication goes away with a known-good PCM, replace the original PCM.n |
| 9. | Shift to all positions other than [N]. |
| 10. | Measure the voltage between PCM connector terminals C20 and A8 or A9. PCM CONNECTORSLG1(BRN/YEL)ATP N (RED/BLK)Wire side of female terminalsA (31P)C (22P)LG2 (BRN/YEL) Is there battery voltage? YES - Go to 11. NO - Check for a short in the wire between PCM connector terminal C20 and the transmission range switch. If the wire is OK, update the PCM if it does not have the latest software, or substitute a known-good PCM, then recheck. If the symptom/indication goes away with a known-good PCM, replace the original PCM.n |
| 11. | Shift to all positions other than [D]. |
| 12. | Measure the voltage between PCM connector terminals C17 and A8 or A9. PCM CONNECTORSLG1(BRN/YEL)ATP D (YEL/GRN)Wire side of female terminalsA (31P)C (22P)LG2 (BRN/YEL) Is there battery voltage? YES - Go to 13. NO - Check for a short in the wire between PCM connector terminal C17 and the transmission range switch. If the wire is OK, update the PCM if it does not have the latest software, or substitute a known-good PCM, then recheck. If the symptom/indication goes away with a known-good PCM, replace the original PCM.n |
| 13. | Shift to all positions other than [D3]. |
| 14. | Measure the voltage between PCM connector terminals C9 and A8 or A9. PCM CONNECTORSLG1(BRN/YEL)ATP D3 (RED)Wire side of female terminalsA (31P)C (22P)LG2 (BRN/YEL) Is there battery voltage? YES - Go to 15. NO - Check for a short in the wire between PCM connector terminal C9 and the transmission range switch. If the wire is OK, update the PCM if it does not have the latest software, or substitute a known-good PCM, then recheck. If the symptom/indication goes away with a known-good PCM, replace the original PCM.n |
| 15. | Shift to all positions other than [D] and [D3]. |
| 16. | Measure the voltage between PCM connector terminals C18 and A8 or A9. PCM CONNECTORSLG1(BRN/YEL)ATP FWD (BLU/YEL)Wire side of female terminalsA (31P)C (22P)LG2 (BRN/YEL) Is there battery voltage? YES - The PCM has failed; replace it.n NO - Check for a short in the wire between PCM connector terminal C18 and the transmission range switch. If the wire is OK, update the PCM if it does not have the latest software, or substitute a known-good PCM, then recheck. If the symptom/indication goes away with a known-good PCM, replace the original PCM.n |