Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM

POWER DOOR LOCK CONTROL SYSTEM > CUSTOMIZE PARAMETERS

for Preparation Click here



1. CUSTOMIZE POWER DOOR LOCK CONTROL SYSTEM

HINT:
The following items can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Be sure to make a note of the current settings before customizing.
  3. When troubleshooting a function, first make sure that the function is set to the default setting.

  1. Customizing with the intelligent tester.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Main Body / Utility / Customize / Door Lock.

    5. Select the setting by referring to the table below.

      Display
      		Default
      		Content
      		Setting
      		Relevant ECU
      Unlock Key Twice
      		ON*1
      OFF*2
      		Function that unlocks only the driver door when the driver door key cylinder is turned to unlock once, and unlock all doors when it is turned to unlock twice. For the OFF setting, turning it once unlocks all doors.
      		ON or OFF
      		Main body ECU (Multiplex network body ECU)
      Auto Lock
      		ON*2
      OFF*1
      		Function that locks all doors when the vehicle speed reaches a certain level.
      		ON or OFF
      		Main body ECU (Multiplex network body ECU)
      Auto Lock/Shift
      		ON*1
      OFF*2
      		Function that locks all doors when the shift lever is moved to select another shift state with park (P) selected, the power switch on (READY) and all doors closed.
      		ON or OFF
      		Main body ECU (Multiplex network body ECU)
      Auto Unlock/Shift
      		ON*1
      OFF*2
      		Function that unlocks all doors when the P position switch (transmission shift main switch) is pushed with a shift state other than park (P) selected and the power switch on (READY).
      		ON or OFF
      		Main body ECU (Multiplex network body ECU)
      All Unlock/Open-Close
      		OFF
      		Function that unlocks the other doors when the driver door is opened within 10 seconds after the power switch is turned off.
      		ON or OFF
      		Main body ECU (Multiplex network body ECU)
      *1: for G.C.C. countries, Australia and New Zealand
      *2: except G.C.C. countries, Australia and New Zealand

  1. Customizing with the combination meter assembly

    HINT:
    1. Press and hold DISP switch (steering pad switch assembly) when entering an item.
    2. Briefly press DISP switch (steering pad switch assembly) when selecting an item.


    1. Turn the power switch on (IG).

    2. Enter the following menus: Settings / Vehicle Settings.

    3. Select the setting by referring to the table below.

      Display
      		Default
      		Content
      		Setting
      		Relevant ECU
      SPEED SENSITIVE AUTO. LOCK
      		ON*2
      OFF*1
      		Function that locks all doors when the vehicle speed reaches a certain level.
      		ON or OFF
      		Main body ECU (Multiplex network body ECU)
      SHIFT-LINKED AUTOMATIC LOCK
      		ON*1
      OFF*2
      		Function that locks all doors when the shift lever is moved to select another shift state with park (P) selected, the power switch on (READY) and all doors closed.
      		ON or OFF
      		Main body ECU (Multiplex network body ECU)
      SHIFT-LINKED AUTOMATIC UNLOCK
      		ON*1
      OFF*2
      		Function that unlocks all doors when the P position switch (transmission shift main switch) is pushed with a shift state other than park (P) selected and the power switch on (READY).
      		ON or OFF
      		Main body ECU (Multiplex network body ECU)
      DRIVER DOOR-LINKED UNLOCK
      		ON*1
      OFF*2
      		Function that unlocks the other doors when the driver door is opened within 10 seconds after the power switch is turned off.
      		ON or OFF
      		Main body ECU (Multiplex network body ECU)
      *1: for G.C.C. countries, Australia and New Zealand
      *2: except G.C.C. countries, Australia and New Zealand

    4. Press and hold DISP switch (steering pad switch assembly).

    5. The setting completion screen will be displayed.

    6. Return to the item selection screen.