Home › Vehicle Interior › DOOR LOCK › DOOR CONTROL RECEIVER

DOOR CONTROL RECEIVER > REMOVAL

for Preparation Click here



1. REMOVE REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure described for the LH side .



2. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure described for the LH side .



3. REMOVE REAR SEAT CUSHION ASSEMBLY


  1. Disengage the hook of the seat cushion from the vehicle body as shown in the illustration.

    NOTICE:
    Follow the instructions below carefully as the cushion frame can be deformed easily.




      B275284E01

    1. Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.
      Text in Illustration 
      *1
      		Hook
      *2
      		Guide
      Standard Measurement 
      *a
      		100 mm (3.94 in.) or less

    2. Repeat the step above for the other hook.

  1. Disengage the guide of the seat cushion from the seatback.



    B221512

  1. Remove the bolt and disconnect the rear center seat outer belt assembly.

  1. Pull out the rear center seat outer belt assembly from the rear seat cushion assembly.

  1. Remove the rear seat cushion assembly.



4. REMOVE REAR SEAT CUSHION LOCK HOOK


    B274369

  1. Disengage the claw and remove the rear seat cushion lock hook.

    NOTICE:
    Rear seat cushion lock hooks must not be reused.

    HINT:
    Use the same procedure the LH side and RH side.



5. REMOVE REAR SEATBACK ASSEMBLY RH

  1. Disengage the fastener and disconnect the rear No. 1 floor board sub-assembly.



    B275063

  1. Remove the 2 bolts and rear seatback assembly RH.

    NOTICE:
    Be careful not to damage the vehicle body.



6. REMOVE REAR NO. 2 FLOOR BOARD

  1. Remove the rear No. 2 floor board.



7. REMOVE REAR DECK FLOOR BOX

  1. Remove the rear deck floor box.



8. REMOVE REAR NO. 3 FLOOR BOARD

  1. Remove the rear No. 3 floor board.



9. REMOVE DECK FLOOR BOX RH


    B270546

  1. Remove the clip.

  1. Disengage the 6 guides and remove the deck floor box RH.



10. REMOVE REAR FLOOR BOARD UPPER NO. 3 PLATE


    B270547

  1. Disengage the 4 claws and 2 guides, and remove the rear floor board upper No. 3 plate.



11. REMOVE REAR NO. 4 FLOOR BOARD (w/o Woofer)

  1. Remove the rear No. 4 floor board.



12. REMOVE REAR NO. 4 FLOOR BOARD (w/ Woofer)


    B270548

  1. Disengage the 2 clips and 3 guides, and remove the rear No. 4 floor board.



13. REMOVE DECK FLOOR BOX LH (w/o Woofer)


    B270549

  1. Remove the clip.

  1. Disengage the 6 guides and remove the deck floor box LH.



14. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

  1. Remove the tonneau cover assembly.



15. REMOVE REAR NO. 1 FLOOR BOARD SUB-ASSEMBLY


    B270540

  1. Disengage the 2 claws and 2 clips, and remove the rear No. 1 floor board sub-assembly.



16. REMOVE REAR NO. 2 FLOOR BOARD SUB-ASSEMBLY


    B270541

  1. Disengage the claw and 2 clips, and remove the rear No. 2 floor board sub-assembly.



17. REMOVE REAR NO. 1 FLOOR BOARD


    B270542

  1. Remove the bolt.

  1. Disengage the 2 claws and 2 clips, and remove the rear No. 1 floor board.



18. REMOVE DECK TRIM SERVICE HOLE COVER


    B270550E01

  1. Disengage the 2 claws and guide (A).

  1. Disengage the 2 guides (B) and remove the deck trim service hole cover.



19. REMOVE REAR DECK TRIM COVER


    B270551

  1. Disengage the 4 clips and remove the rear deck trim cover.



20. REMOVE REAR SEAT SIDE COVER RH


    B270543

  1. Disengage the 3 claws and 2 clips, and remove the rear seat side cover RH.



21. REMOVE REAR SEAT SIDE GARNISH RH

HINT:
Use the same procedure described for the LH side .



22. REMOVE ROPE HOOK ASSEMBLY

HINT:
Use the same procedure described for the LH side .



23. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY

HINT:
Use the same procedure described for the LH side .



24. REMOVE TONNEAU COVER HOOK


    B270563E01

  1. Using a screwdriver, disengage the 2 claws and pin, and remove the tonneau cover hook.
    Text in Illustration 
    *1
    		Protective Tape

    HINT:
    Tape the screwdriver tip before use.



25. REMOVE TONNEAU COVER HOLDER CAP

HINT:
Use the same procedure described for the LH side .



26. REMOVE NO. 2 ROOM LIGHT ASSEMBLY


    E219171E01

  1. Using a screwdriver with its tip wrapped with protective tape, disengage the claw.
    Text in Illustration 
    *1
    		Protective Tape

  1. Disconnect the connector and remove the No. 2 room light assembly.



27. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY RH

HINT:
Use the same procedure described for the LH side .



28. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH

HINT:
Use the same procedure described for the LH side .



29. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH

HINT:
Use the same procedure described for the LH side .



30. REMOVE DOOR CONTROL RECEIVER


    B268131

  1. Disconnect the connector.

  1. Remove the bolt and door control receiver.