Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > CUSTOMIZE PARAMETERS

for Preparation Click here



1. CUSTOMIZE METER / GAUGE SYSTEM

  1. Customizing with the intelligent tester

    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus:

      1. for Warning: Customize Setting / Combination Meter / Warning.
      2. for Display: Customize Setting / Combination Meter / Display.

    5. Select the setting by referring to the table below.

      NOTICE:
      1. Be sure to record the current value before customizing.

      HINT:
      The following items can be customized using the intelligent tester.


      Warning 
      Tester Display
      		Default
      		Content
      		Setting
      		Relevant ECU
      Driver Side Seatbelt Warning Buzzer*1
      		ON
      		Function to turn on/off the seat belt warning buzzer
      		ON or OFF
      		Combination meter assembly
      Front Passenger Side Seatbelt Warning Buzzer*1
      		ON
      		Function to turn on/off the seat belt warning buzzer
      		ON or OFF
      		Combination meter assembly
      Rear Seatbelt Warning Buzzer*2
      		ON
      		Function to turn on/off the rear seat belt warning buzzer
      		ON or OFF
      		Combination meter assembly
      Reverse Buzzer
      		Continual
      		Function to change the type of the reverse warning buzzer
      		Single or Continual
      		Combination meter assembly
      1. *1: This setting is only valid for the buzzer which sounds at 20 km/h (12 mph) or more
      2. *2: w/ Rear Seat Belt Warning

  1. Customizing with the combination meter assembly

    HINT:
    1. Press and hold the DISP switch (steering pad switch assembly) when entering an item.
    2. Briefly pressed the DISP switch (steering pad switch assembly) when selecting an item.


    1. Turn the power switch on (IG).

    2. Select the following menus: SETTINGS / METER SETTING.

    3. Select the setting by referring to the table below.

      NOTICE:
      1. Be sure to record the current value before customizing.

      HINT:
      The following items can be customized operating the combination meter assembly.


      Meter Setting 
      Tester Display
      		Default
      		Content
      		Setting
      		Relevant ECU
      TACHO METER
      		AUTO
      		Function to change the tachometer setting
      		AUTO, KEEP ON, OFF
      		Combination meter assembly
      ECO LAMP
      		ECO DRIVE SUPPORT
      		Function to change the illumination level
      		ECO DRIVE SUPPORT, KEEP ON, OFF
      		Combination meter assembly
      SPORT LAMP
      		AUTO
      		Function to change the sport illumination
      		AUTO, OFF
      		Combination meter assembly
      LAMP BRIGHTNESS
      		STANDARD
      		Function to change the illumination light
      		BRIGHT, STANDARD
      		Combination meter assembly
      EV INDICATOR
      		AUTO
      		Function to change the EV indicator setting
      		AUTO, OFF
      		Combination meter assembly
      LANGUAGE
      		ENGLISH
      		Function to change the multi-information display language
      		ENGLISH, FRENCH, SPANISH
      		Combination meter assembly
      UNITS
      		KM (L/1100KM) or MILES (MPG)*1
      		Function to change the multi-information display unit
      		KM (KM/L), KM (L/100KM), MILES (MPG)
      		Combination meter assembly
      1. *1: The default setting is changed according to the vehicle specification

    4. Press and hold DISP switch (steering pad switch assembly).

    5. The setting completion screen will be displayed.

    6. Return to the item selection screen.