Lexus IS250 · Service Manual BODY

INSPECTION

Inspection


INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/ Memory)

  1. B126309E01
    Inspect outer mirror motor operation.

    1. Apply battery voltage and check operation of the mirror face, as shown in the table and illustration.

      Standard:
      Measurement Condition
      		 Specified Condition
      Battery positive (+) → Terminal 1 (MV)
      Battery negative (-) → Terminal 10 (M+)
      		 Turns upward (A)
      Battery positive (+) → Terminal 10 (M+)
      Battery negative (-) → Terminal 1 (MV)
      		 Turns downward (B)
      Battery positive (+) → Terminal 9 (MH)
      Battery negative (-) → Terminal 10 (M+)
      		 Turns left (C)
      Battery positive (+) → Terminal 10 (M+)
      Battery negative (-) → Terminal 9 (MH)
      		 Turns right (D)

  1. Inspect the retract mirror operation.

    1. Apply battery voltage and check operation of the mirror, as shown in the table below.

      Standard:
      Measurement Condition
      		 Specified Condition
      Battery positive (+) → Terminal 7 (MF)
      Battery negative (-) → Terminal 1 (MV)
      		 Returns (Driving position)
      Battery positive (+) → Terminal 1 (MV)
      Battery negative (-) → Terminal 7 (MF)
      		 Retracts

  1. Inspect outer mirror heater operation.

    1. Apply battery voltage and check operation of the mirror face, as shown in the table below.

      Standard:
      Measurement Condition
      		 Specified Condition
      Battery positive (+) → Terminal 3 (HTR+)
      Battery negative (-) → Terminal 9 (HTR-)
      		 Mirror surface temperature becomes higher

  1. B126310E01
    Inspect electrochromic outer mirror operation.

    1. Apply battery voltage and check operation of the mirror face, as shown in the table and illustration.

      Standard:
      Measurement Condition
      		 Specified Condition
      Battery positive (+) → Terminal 7 (EC+)
      Battery negative (-) → Terminal 15 (EC-)
      		 Mirror surface changes to dark


INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/o Memory)

  1. B126313E01
    Inspect outer mirror motor operation.

    1. Apply battery voltage and check operation of the mirror face, as shown in the table and illustration.

      Standard:
      Measurement Condition
      		 Specified Condition
      Battery positive (+) → Terminal 5 (MV)
      Battery negative (-) → Terminal 6 (M+)
      		 Turns upward (A)
      Battery positive (+) → Terminal 6 (M+)
      Battery negative (-) → Terminal 5 (MV)
      		 Turns downward (B)
      Battery positive (+) → Terminal 11 (MH)
      Battery negative (-) → Terminal 6 (M+)
      		 Turns left (C)
      Battery positive (+) → Terminal 6 (M+)
      Battery negative (-) → Terminal 11 (MH)
      		 Turns right (D)

  1. Inspect the retract mirror operation.

    1. Apply battery voltage and check operation of the mirror, as shown in the table below.

      Standard:
      Measurement Condition
      		 Specified Condition
      Battery positive (+) → Terminal 7 (MF)
      Battery negative (-) → Terminal 1 (MV)
      		 Returns (Driving position)
      Battery positive (+) → Terminal 1 (MV)
      Battery negative (-) → Terminal 7 (MF)
      		 Retracts

  1. Inspect outer mirror heater operation.

    1. Apply battery voltage and check operation of the mirror face, as shown in the table below.

      Standard:
      Measurement Condition
      		 Specified Condition
      Battery positive (+) → Terminal 3 (HTR+)
      Battery negative (-) → Terminal 9 (HTR-)
      		 Mirror surface temperature becomes higher

  1. B126314E01
    Inspect electrochromic outer mirror operation.

    1. Apply battery voltage and check operation of the mirror face, as shown in the table and illustration.

      Standard:
      Measurement Condition
      		 Specified Condition
      Battery positive (+) → Terminal 4 (EC+)
      Battery negative (-) → Terminal 10 (EC-)
      		 Mirror surface changes to dark


INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/ Memory)

  1. B126307E01
    Inspect outer mirror motor operation.

    1. Remove the outer rear view mirror assembly.

    2. Apply battery voltage and check operation of the mirror face, as shown in the table and illustration.

      Standard:
      Measurement Condition
      		 Specified Condition
      Battery positive (+) → Terminal 1 (MV)
      Battery negative (-) → Terminal 10 (M+)
      		 Turns upward (A)
      Battery positive (+) → Terminal 10 (M+)
      Battery negative (-) → Terminal 1 (MV)
      		 Turns downward (B)
      Battery positive (+) → Terminal 9 (LMHR)
      Battery negative (-) → Terminal 10 (LM+R)
      		 Turns left (C)
      Battery positive (+) → Terminal 10 (M+)
      Battery negative (-) → Terminal 9 (MH)
      		 Turns right (D)

  1. Inspect the retract mirror operation.

    1. Apply battery voltage and check operation of the mirror, as shown in the table below.

      Standard:
      Measurement Condition
      		 Specified Condition
      Battery positive (+) → Terminal 7 (MF)
      Battery negative (-) → Terminal 1 (MV)
      		 Returns (Driving position)
      Battery positive (+) → Terminal 1 (MV)
      Battery negative (-) → Terminal 7 (MF)
      		 Retracts

  1. Inspect outer mirror heater operation.

    1. Apply battery voltage and check operation of the mirror face, as shown in the table below.

      Standard:
      Measurement Condition
      		 Specified Condition
      Battery positive (+) → Terminal 3 (HTR+)
      Battery negative (-) → Terminal 9 (HTR-)
      		 Mirror surface temperature becomes higher

  1. B126308E01
    Inspect electrochromic outer mirror operation.

    1. Apply battery voltage and check operation of the mirror face, as shown in the table and illustration.

      Standard:
      Measurement Condition
      		 Specified Condition
      Battery positive (+) → Terminal 7 (EC+)
      Battery negative (-) → Terminal 15 (EC-)
      		 Mirror surface changes to dark


INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/o Memory)

  1. B126311E01
    Inspect outer mirror motor operation.

    1. Apply battery voltage and check operation of the mirror face, as shown in the table and illustration.

      Standard:
      Measurement Condition
      		 Specified Condition
      Battery positive (+) → Terminal 5 (MV)
      Battery negative (-) → Terminal 6 (M+)
      		 Turns upward (A)
      Battery positive (+) → Terminal 6 (M+)
      Battery negative (-) → Terminal 5 (MV)
      		 Turns downward (B)
      Battery positive (+) → Terminal 11 (MH)
      Battery negative (-) → Terminal 6 (M+)
      		 Turns left (C)
      Battery positive (+) → Terminal 6 (M+)
      Battery negative (-) → Terminal 11 (MH)
      		 Turns right (D)

  1. Inspect the retract mirror operation.

    1. Apply battery voltage and check operation of the mirror, as shown in the table below.

      Standard:
      Measurement Condition
      		 Specified Condition
      Battery positive (+) → Terminal 7 (MF)
      Battery negative (-) → Terminal 1 (MV)
      		 Returns (Driving position)
      Battery positive (+) → Terminal 1 (MV)
      Battery negative (-) → Terminal 7 (MF)
      		 Retracts

  1. Inspect outer mirror heater operation.

    1. Apply battery voltage and check operation of the mirror face, as shown in the table below.

      Standard:
      Measurement Condition
      		 Specified Condition
      Battery positive (+) → Terminal 3 (HTR+)
      Battery negative (-) → Terminal 9 (HTR-)
      		 Mirror surface temperature becomes higher

  1. B126312E01
    Inspect electrochromic outer mirror operation.

    1. Apply battery voltage and check operation of the mirror face, as shown in the table and illustration.

      Standard:
      Measurement Condition
      		 Specified Condition
      Battery positive (+) → Terminal 4 (EC+)
      Battery negative (-) → Terminal 10 (EC-)
      		 Mirror surface changes to dark

← REMOVALINSTALLATION →