Lexus IS250 · Service Manual BODY ELECTRICAL

INSTALLATION

Removal / installation


1. INSTALL REAR STEREO COMPONENT SPEAKER ASSEMBLY (w/ Front Center Speaker)

  1. E119009
    Engage the clip to the vehicle body to temporarily install the rear stereo component speaker assembly.

  1. E121394
    Install the rear stereo component speaker assembly with the bolt.

  1. Connect the connector.


2. INSTALL NO. 2 PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Front Center Speaker)

  1. B126804
    Engage the 5 claws and 3 clips, and install the No. 2 package tray trim panel assembly.


3. INSTALL STEREO COMPONENT SPEAKER ASSEMBLY

  1. E117361E02
    Install the stereo component speaker assembly with the 4 bolts.

    HINT:
    Install the bolts in the order shown in the illustration.

  1. Connect the connector.


4. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY

  1. B126805
    Thread the 3 rear seat belt floor anchors into the package tray trim panel assembly.

  1. Insert the rear end of the package tray trim panel assembly into the rear window shade assembly.

  1. Engage the 3 clips and install the package tray trim panel assembly.

  1. B126803
    Engage the 2 claws and install the rear seat shoulder belt cover.

    HINT:
    Use the same procedure for the other 2 rear seat shoulder belt covers.

  1. B125797E01
    Connect the floor side of the rear seat inner with center belt assembly RH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the rear seat inner with center belt assembly RH and the protruding parts of the floor panel to overlap.

  1. Check if the ELR locks.

    NOTICE:
    The check should be performed with the outer belt assembly installed.


    1. With the belt assembly installed, check that the belt locks when the belt is pulled out quickly.

  1. B122792E01
    Connect the floor side of the rear seat 3 point type belt assembly LH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the rear seat 3 point type belt assembly LH and the protruding parts of the floor panel to overlap.

    HINT:
    Use the same procedures for the RH side and the LH side.

  1. Check if the ELR locks.

    NOTICE:
    The check should be performed with the outer belt assembly installed.


    1. With the belt assembly installed, check that the belt locks when the belt is pulled out quickly.


5. INSTALL ROOF SIDE INNER GARNISH LH

  1. B125407
    Engage the claw and 4 clips, and install the roof side garnish inner LH.


6. INSTALL ROOF SIDE INNER GARNISH RH

7. INSTALL REAR SIDE SEAT GARNISH LH

  1. B125408
    Engage the 5 claws and install the rear seat side garnish LH.


8. INSTALL REAR SIDE SEAT GARNISH RH

9. INSTALL REAR DOOR SCUFF PLATE LH

  1. B125404
    Engage the 2 clips.

  1. B125387
    Engage the 5 claws and install the rear door scuff plate LH.


10. INSTALL REAR DOOR SCUFF PLATE RH

11. INSTALL REAR SEATBACK ASSEMBLY

  1. B121660
    Place the seatback in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Install the seatback with the 4 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. Pass the 3 seat belts through and close the cap of the 2 rear seat shoulder belt guides.

  1. Install the floor anchor part with the bolt.


12. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY

13. INSTALL REAR SEAT HEADREST ASSEMBLY

14. INSTALL REAR SEAT CUSHION ASSEMBLY

  1. B123725E02
    Attach the 2 rear hooks of the seat cushion to the seatback.

  1. Attach the 2 front hooks of the seat cushion to the vehicle body.

  1. Confirm that the seat cushion is firmly installed.

    NOTICE:
    When installing the seat cushion, make sure the seat belt buckle is not under the seat cushion.

← REMOVALCOMPONENTS →