Lexus IS250 · Service Manual BODY

REMOVAL

Removal / installation


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG

  1. B122641
    Using a screwdriver wrapped with protective tape, disengage the 3 claws, and remove the front door inside handle bezel plug.


3. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

  1. B122642
    Using a screwdriver wrapped with protective tape, disengage the 4 claws and the 2 clips.

  1. Disconnect the connector and remove the power window regulator master switch assembly.


4. REMOVE COURTESY LIGHT ASSEMBLY

  1. B122643
    Disengage the claw and remove the courtesy light assembly.

  1. Disconnect the connector.


5. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

  1. B122644
    Remove the 2 screws.

  1. Using the clip remover, disengage the 9 clips.

  1. B127038E01
    Pull out the front door trim board in the direction indicated by the arrow.

  1. Remove the reference bosses from the front door panel.

  1. Raise the front door trim board to disengage the 4 claws and remove the front door trim board together with the front door inner glass weatherstrip.

  1. B122646
    Disconnect the cables and each connector from the back side of the inside handle and remove the front door trim board sub-assembly.

  1. Remove the 2 front door trim board retainers (green) from the front door trim board.


6. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP

  1. B127040
    Disengage the 4 clips as shown in the illustration and remove the front door inner glass weatherstrip from the front door trim board.


7. REMOVE FRONT DOOR SERVICE HOLE COVER

  1. B124465
    Disconnect each connector and each clamp, and remove the front door service hole cover.

    HINT:
    Remove the remaining butyl tape on the door side.


8. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

  1. B124466
    Remove the hole plug.

  1. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

  1. B124467
    Remove the 2 bolts.

    NOTICE:
    After the bolts are removed, the door glass may fall and become deformed.

  1. B124468E01
    Remove the front door glass sub-assembly as shown in the illustration.

    NOTICE:
    Do not damage the door glass.

  1. Disconnect the power window regulator master switch assembly.


9. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY

  1. B124469E01
    Disconnect the connector.

  1. Loosen the temporary bolt.

    NOTICE:
    If the temporary bolt is removed, the front door window regulator may fall and become deformed.

  1. Remove the 5 bolts.

  1. Remove the front door window regulator sub-assembly and the power window regulator motor assembly front as a unit.

  1. Remove the temporary bolt from the front door window regulator sub-assembly.


10. REMOVE FRONT POWER WINDOW REGULATOR MOTOR

  1. B124470
    Using a "torx" socket wrench (T25), remove the 3 screws and the front power window regulator motor.


11. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG

  1. B124501
    Using a screwdriver wrapped with protective tape, disengage the 3 claws and remove the rear door inside handle bezel plug.


12. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY

  1. B124502
    Using a screwdriver wrapped with protective tape, disengage the 2 claws and 2 clips.

  1. Disconnect the connector and remove the rear power window regulator switch assembly.


13. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

  1. B124503
    Remove the 2 screws.

  1. Using the clip remover, disengage the 8 clips.

  1. B127039E01
    Pull out the rear door trim board in the direction indicated by the arrow.

  1. Remove the reference bosses from the rear door panel.

  1. Raise the rear door trim board to disengage the 3 claws and remove the rear door trim board together with the rear door inner glass weatherstrip.

  1. B124505
    Disconnect the cables and each connector from the back side of the inside handle and the rear door trim board sub-assembly, remove the rear door trim board sub-assembly.

  1. Remove the 2 rear door trim board retainers (green) from the rear door trim board.


14. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP

  1. B127041
    Disengage the 3 clips as shown in the illustration and remove the rear door inner glass weatherstrip from the rear door trim board.


15. REMOVE REAR DOOR SERVICE HOLE COVER

  1. B124511
    Disconnect the connector and 2 clamps.

  1. Remove the rear door service hole cover.

    HINT:
    Remove the remaining tape on the door side.


16. REMOVE REAR DOOR GLASS RUN

  1. B124515
    Remove the rear door glass run.


17. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

  1. B124516
    Remove the 2 bolts, the screw, and the rear door window division bar sub-assembly.


18. REMOVE REAR DOOR QUARTER WINDOW GLASS

  1. B124517
    Remove the rear door quarter window glass and the rear door quarter window weatherstrip as a unit as shown in the illustration.

  1. Remove the rear door quarter window glass from the rear door quarter window weatherstrip.


19. REMOVE REAR DOOR GLASS SUB-ASSEMBLY

  1. B124518
    Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

    NOTICE:
    Do not damage the door glass.


20. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY

  1. B124519E01
    Disconnect the connector.

  1. Loosen the temporary bolt.

    NOTICE:
    If the temporary bolt is removed, the rear door window regulator may fall and become deformed.

  1. Remove the 3 bolts.

  1. Remove the rear door window regulator sub-assembly and the power window regulator motor assembly rear as a unit.

  1. Remove the temporary bolt from the rear door window regulator.


21. REMOVE REAR POWER WINDOW REGULATOR MOTOR

  1. B124520
    Using a "torx" socket wrench (T25), remove the 3 screws and the rear power window regulator motor.

← COMPONENTSINSPECTION →