RX400h · Service Manual RESTRAINTS

INSTALLATION

Removal / installation

HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.


1. INSTALL SIDE AIRBAG SENSOR LH

  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) terminal is disconnected.

    CAUTION:
    After disconnecting the negative battery terminal, wait for at least 90 seconds before starting the operation.

  1. H042706E01
    Install the side airbag sensor LH with the 2 bolts.

    Torque:
    17.5 N*m{ 179 kgf*cm , 13 ft.*lbf }

    NOTICE:
    1. If the side airbag sensor LH has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.
    2. When installing the side airbag sensor LH, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

  1. Check that there is no looseness in the installation parts of the side airbag sensor LH.

  1. Connect the connetor to the side airbag sensor LH.


2. INSTALL FRONT SEAT OUTER BELT ASSEMBLY

  1. B115713
    Check the degree of tilt when the ELR begins to lock.

    1. Check that the belt does not lock at less than 15 degrees of tilt in any direction but locks at over 45 degrees of tilt when gently moving the installed retractor.

      NOTICE:
      Do not disassemble the retractor.

  1. B115712
    Temporarily install the front seat outer belt assembly with the 2 bolts.

  1. Fully tighten the upper side bolt first, then the lower side bolt to install the front seat outer belt assembly.

    Torque:
    For upper bolt:
    7.5 N*m{ 77 kgf*cm , 66 in.*lbf }
    For lower bolt:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. B112935
    Connect the tension reducer connector.

  1. Connect the pretensioner connector and lock the locking button.

    NOTICE:
    Securely lock the locking button.

  1. Connect the shoulder side of the front seat outer belt assembly with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


3. INSTALL CENTER PILLAR LH GARNISH LOWER

  1. B111788
    Engage the 2 clips and 3 claws, install the center pillar garnish lower.


4. INSTALL LAP BELT OUTER ANCHOR COVER

  1. B110478
    Engage the 2 claws and install the lap belt outer anchor cover as shown in the illustration.

    HINT:
    Use the same procedure to install the other side.


5. INSTALL REAR DOOR OPENING TRIM LH WEATHERSTRIP

6. INSTALL FRONT DOOR OPENING TRIM LH WEATHERSTRIP

7. INSTALL REAR DOOR SCUFF LH PLATE

  1. B111783
    Connect the connector. (w/ illumination scuff plate)

  1. Engage the 4 claws and 2 clips, and install the rear door scuff plate.


8. INSTALL FRONT DOOR SCUFF LH PLATE

  1. B111782
    Connect the connector. (w/ illumination scuff plate)

  1. Engage the 6 claws and 4 clips, and install the front door scuff plate.


9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

10. PERFORM INITIALIZATION

  1. Perform initialization (Click here).

    HINT:
    Some systems need initialization when disconnecting the cable from the negative battery terminal.


11. INSPECT SRS WARNING LIGHT

  1. Inspect the SRS warning light (Click here).

← REMOVALCOMPONENTS →