RX400h · Service Manual BODY

INSPECTION

Inspection


INSPECT FRONT POWER SEAT SWITCH

  1. B105970E03
    Inspect the LH side power seat switch.

    1. Measure the resistance according to the value(s) in the table below.

      Resistance:
      Slide switch:
      Tester Connection
      		 Switch Condition
      		 Specified Condition
      1(B) - 9(SLDF)
      		 FRONT
      		 Below 1 Ω
      4(E) - 6(SLDR)
      		 FRONT
      		 Below 1 Ω
      4(E) - 6(SLDR)
      		 OFF
      		 Below 1 Ω
      4(E) - 9(SLDF)
      		 OFF
      		 Below 1 Ω
      1(B) - 6(SLDR)
      		 REAR
      		 Below 1 Ω
      4(E) - 9(SLDF)
      		 REAR
      		 Below 1 Ω
      Front vertical switch:
      Tester Connection
      		 Switch Condition
      		 Specified Condition
      1(B) - 10(FUP)
      		 UP
      		 Below 1 Ω
      4(E) - 5(FDWN)
      		 UP
      		 Below 1 Ω
      4(E) - 5(FDWN)
      		 OFF
      		 Below 1 Ω
      4(E) - 10(FUP)
      		 OFF
      		 Below 1 Ω
      1(B) - 5(FDWN)
      		 DOWN
      		 Below 1 Ω
      4(E) - 10(FUP)
      		 DOWN
      		 Below 1 Ω
      Lifter switch:
      Tester Connection
      		 Switch Condition
      		 Specified Condition
      1(B) - 7(LUP)
      		 UP
      		 Below 1 Ω
      4(E) - 8(LDWN)
      		 UP
      		 Below 1 Ω
      4(E) - 7(LUP)
      		 OFF
      		 Below 1 Ω
      4(E) - 8(LDWN)
      		 OFF
      		 Below 1 Ω
      1(B) - 8(LDWN)
      		 DOWN
      		 Below 1 Ω
      4(E) - 7(LUP)
      		 DOWN
      		 Below 1 Ω
      Reclining switch:
      Tester Connection
      		 Switch Condition
      		 Specified Condition
      1(B) - 3(RCLF)
      		 FRONT
      		 Below 1 Ω
      2(RCLR) - 4(E)
      		 FRONT
      		 Below 1 Ω
      2(RCLR) - 4(E)
      		 OFF
      		 Below 1 Ω
      3(RCLF) - 4(E)
      		 OFF
      		 Below 1 Ω
      1(B) - 2(RCLR)
      		 REAR
      		 Below 1 Ω
      3(RCLF) - 4(E)
      		 REAR
      		 Below 1 Ω

      If the result is not as specified, replace the switch.

  1. B105969E02
    Inspect the RH side power seat switch.

    1. Measure the resistance according to the value(s) in the table below.

      Resistance:
      Slide switch:
      Tester Connection
      		 Switch Condition
      		 Specified Condition
      1(B) - 9(SLDF)
      		 FRONT
      		 Below 1 Ω
      4(E) - 6(SLDR)
      		 FRONT
      		 Below 1 Ω
      4(E) - 6(SLDR)
      		 OFF
      		 Below 1 Ω
      4(E) - 9(SLDF)
      		 OFF
      		 Below 1 Ω
      1(B) - 6(SLDR)
      		 REAR
      		 Below 1 Ω
      4(E) - 9(SLDF)
      		 REAR
      		 Below 1 Ω
      Front vertical switch:
      Tester Connection
      		 Switch Condition
      		 Specified Condition
      1(B) - 5(FUP)
      		 UP
      		 Below 1 Ω
      4(E) - 10(FDWN)
      		 UP
      		 Below 1 Ω
      4(E) - 5(FUP)
      		 OFF
      		 Below 1 Ω
      4(E) - 10(FDWN)
      		 OFF
      		 Below 1 Ω
      1(B) - 10(FDWN)
      		 DOWN
      		 Below 1 Ω
      4(E) - 5(FUP)
      		 DOWN
      		 Below 1 Ω
      Lifter switch:
      Tester Connection
      		 Switch Condition
      		 Specified Condition
      1(B) - 8(LUP)
      		 UP
      		 Below 1 Ω
      4(E) - 7(LDWN)
      		 UP
      		 Below 1 Ω
      4(E) - 7(LDWN)
      		 OFF
      		 Below 1 Ω
      4(E) - 8(LUP)
      		 OFF
      		 Below 1 Ω
      1(B) - 7(LDWN)
      		 DOWN
      		 Below 1 Ω
      4(E) - 8(LUP)
      		 DOWN
      		 Below 1 Ω
      Reclining switch:
      Tester Connection
      		 Switch Condition
      		 Specified Condition
      1(B) - 3(RCLF)
      		 FRONT
      		 Below 1 Ω
      2(RCLR) - 4(E)
      		 FRONT
      		 Below 1 Ω
      2(RCLR) - 4(E)
      		 OFF
      		 Below 1 Ω
      3(RCLF) - 4(E)
      		 OFF
      		 Below 1 Ω
      1(B) - 2(RCLR)
      		 REAR
      		 Below 1 Ω
      3(RCLF) - 4(E)
      		 REAR
      		 Below 1 Ω

      If the result is not as specified, replace the switch.

← INSPECTIONINSPECTION →