RX400h · Service Manual BODY ELECTRICAL

Front Passenger Side Double Lock Motor Circuit

Circuit diagnosis

DESCRIPTION

The front passenger door double lock motor is built into the front passenger door lock assembly.
The door opening relay receives front passenger door double door lock set/release signals from the body ECU using multiplex communication.
The door opening relay controls the double lock motor to set/release the double door lock. This relay applies current from terminal ACTS to terminal ACTR to operate the motor to set the lock. It reverses the direction of the current to operate the motor to release the lock.

WIRING DIAGRAM

B109776E02

INSPECTION PROCEDURE


1. INSPECT FRONT DOOR LOCK ASSEMBLY RH,LH (DOUBLE LOCK MOTOR)

  1. B064708E01
    LHD Models:Remove the front door lock assembly RH.

    1. Apply battery voltage and set the door lock motor to the lock position.

      OK:
      Measurement Condition
      		 Specified Condition
      Battery positive (+) →Terminal 2
      Battery negative (-) →Terminal 1
      		 Lock

    2. Apply battery voltage to the door lock and check operation of the double lock motor.

      OK:
      Measurement Condition
      		 Specified Condition
      Battery positive (+) →Terminal 4
      Battery negative (-) →Terminal 3
      		 Double Locking System is set
      Battery positive (+) →Terminal 3
      Battery negative (-) →Terminal 4
      		 Double Locking System is unset

    3. Check that the doors cannot be unlocked by operating the control cable while the double locking system is set.

  1. B069901E01
    RHD Models:Remove the front door lock assembly LH.

    1. Apply battery voltage and set the door lock motor to the lock position.

      OK:
      Measurement Condition
      		 Specified Condition
      Battery positive (+) →Terminal 4
      Battery negative (-) →Terminal 3
      		 Lock

    2. Apply battery voltage to the door lock and check operation of the double lock motor.

      OK:
      Measurement Condition
      		 Specified Condition
      Battery positive (+) →Terminal 2
      Battery negative (-) →Terminal 1
      		 Double Locking System is set
      Battery positive (+) →Terminal 1
      Battery negative (-) →Terminal 2
      		 Double Locking System is unset

    3. Check that the doors cannot be unlocked by operating the control cable while the double locking system is set.



 NG
REPLACE FRONT DOOR LOCK ASSEMBLY
OK


2. CHECK WIRE HARNESS (FRONT DOOR LOCK ASSEMBLY RH,LH - DOOR OPENING RELAY ASSEMBLY)

  1. B111709E14
    LHD Models:Disconnect the front door lock assembly RH connector.

    1. Disconnect the door opening relay assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      		 Condition
      		 Specified Condition
      D13-4 (DL) - D2-3 (ACTS)
      		 Always
      		 Below 1 Ω
      D13-3 (UNDL) - D2-4 (ACTR)
      		 Always
      		 Below 1 Ω

  1. B111709E15
    RHD Models:Disconnect the front door lock assembly LH connector.

    1. Disconnect the door opening relay assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      		 Condition
      		 Specified Condition
      D13-2 (DL) - D2-3 (ACTS)
      		 Always
      		 Below 1 Ω
      D13-1 (UNDL) - D2-4 (ACTR)
      		 Always
      		 Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE


← Driver Side Double Lock Motor CircuitRear Double Lock Motor LH Circuit →