[ Model - ECLIPSE CROSS / Year - 2018 ]
2018 / ECLIPSE CROSS / EC - Workshop Manual
23 -AUTOMATIC TRANSMISSION > 23A-CVT > OIL PAN AND VALVE BODY ASSEMBLY > OIL PAN AND VALVE BODY ASSEMBLY REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
caution
  • Before replacing the valve body, you should make a note of the serial No. which is stamped on the new valve body assembly (Refer to ).
  • When the CVT fluid is refilled, air-bleed the electric oil pump (Refer to ).
  • When the valve body assembly is replaced, carry out the following operations.
    • Initialisation Procedure for CVT Learned Value (Refer to ).
    • Learning Procedure (Refer to ).
 
 
Pre-removal operation
  • Engine Room Under Cover Front A, B and Engine Room Side Cover (LH) Removal (Refer to GROUP 51 - Under Cover ).
  • CVT Assembly Connector Disconnection (Refer to ).
  • CVT Fluid Draining (Refer to ).
Post-installation operation
  • Engine Room Under Cover Front A, B and Engine Room Side Cover (LH) Installation (Refer to GROUP 51 - Under Cover ).
  • CVT Assembly Connector Connection (Refer to ).
  • CVT Fluid Refilling (Refer to ).
 
Removal steps
<<A>>1.Snap ring
>>E<<2.Oil pan
>>D<<3.Oil pan gasket
4.Magnet
5.Strainer tube
6.O-ring
>>C<<7.Oil strainer
8.O-ring
9.Bracket
10.Spring washer
11.Manual lever
<<B>>>>B<<12.Valve body assembly
>>A<<13.Lip seal
14.Valve body harness

 
 
REMOVAL SERVICE POINTS
 
 
<<A>> SNAP RING REMOVAL
cautionBe careful not to cause damage to the terminal body.
 
Remove the snap ring from the terminal body, and press the terminal body into the transmission case.
 

 
 
<<B>> VALVE BODY ASSEMBLY REMOVAL
 
Tilt the control valve assembly, and after removing from the manual shaft side, remove the terminal body from the transmission case.
 
 

 
 
INSTALLATION SERVICE POINTS
 
 
>>A<< LIP SEAL INSTALLATION
 
caution
  • Do not re-use the lip seal.
  • Apply CVT fluid or vaseline when installing the lip seal.
 

 
 
>>B<< VALVE BODY ASSEMBLY INSTALLATION
Install the control valve assembly on the transmission case as follows.
 
1. Install the valve body harness on the control valve assembly.
 
 
2.
caution
  • Push in the valve body harness until the detent contacts the transmission case.
  • Be careful not to cause damage to the terminal body.
Install the terminal body on the transmission case, while aligning the detent of terminal body with the transmission case as shown in the diagram.
 
3. Slide the control valve assembly from the left side, and install it on the transmission case.
 
4. Install the fastening bolts of control valve assembly, and tighten to the specified torque of 7.9 N·m.
 
Bolt symbolABC
Shank length mm544454
Quantity812
 

 
 
>>C<< OIL STRAINER INSTALLATION
 
Install the oil strainer, and tighten the fastening bolts to the specified torque of 7.9 N·m.
 
Bolt symbolAB
Shank length mm4412
Quantity12
 

 
 
>>D<< OIL PAN GASKET INSTALLATION
 
caution
  • Do not re-use the oil pan gasket.
  • Remove any moisture, oil, and used gasket from the mounting surface of oil pan gasket.
  • When installing the oil pan gasket, align the dowel pins of transmission case with dowel pin holes A of the oil pan gasket.
 

 
 
>>E<< OIL PAN INSTALLATION
cautionWhen installing the oil pan, align the dowel pins of transmission case with dowel pin holes A of the oil pan.
 
Tighten each oil pan mounting bolt to the specified torque of 5.9 N·m in the order of number shown.