[ Model - ECLIPSE CROSS / Year - 2018 ]
2018 / ECLIPSE CROSS / EC - Workshop Manual
35 -SERVICE BRAKES > 35C-ACTIVE STABILITY CONTROL SYSTEM (ASC) > TROUBLESHOOTING<ASC-ECU><ASC-ECU> > DIAGNOSIS CODE PROCEDURES > CODE NO. C100A, C1015, C1020, C102B ABNORMALITY IN WHEEL SPEED SENSOR CIRCUIT
Code No. C100A FL Wheel Speed Sensor Circuit
Code No. C1015 FR Wheel Speed Sensor Circuit
Code No. C1020 RL Wheel Speed Sensor Circuit
Code No. C102B RR Wheel Speed Sensor Circuit
 
 
caution
  • If there is any problem in the CAN bus lines, an incorrect diagnosis code may be set. Prior to this diagnosis, diagnose the CAN bus lines (Refer to GROUP 54C - CAN Bus Diagnostics Table ).
  • Whenever ECU is replaced, ensure that the CAN bus lines are normal.
 
 
OPERATION
  • The wheel speed sensor is a kind of a pulse generator. It consists of encoders (a plate on which north and south pole sides of the magnets are arranged alternately) for detecting the wheel speed which rotates at the same speed of the wheels and wheel speed sensors. This sensor outputs frequency pulse signals in proportion to the wheel speed.
  • The pulse signals, which the wheel speed sensor creates, are sent to ASC-ECU. ASC-ECU uses the frequency of the pulse signals to determine the wheel speed.
 
 
 
DIAGNOSIS CODE SET CONDITIONS
ASC-ECU monitors the voltage fluctuation in each wheel speed sensor circuit. If ASC-ECU detects the open or short circuit in the circuit, it will set a diagnosis code.
 
 
 
PROBABLE CAUSES
Current trouble
  • Damaged wiring harness and connectors
  • Noise interference
  • Malfunction of wheel speed sensor
  • Malfunction of ASC-ECU
Past trouble
  • Carry out diagnosis with particular emphasis on wiring harness and connector failures between ASC-ECU and the wheel speed sensor. For diagnosis procedures, refer to How to treat past trouble (GROUP 00 - How to Use Troubleshooting/How to Treat Past Trouble ).
 
 
 
 
DIAGNOSIS PROCEDURE
STEP 1. M.U.T.-IIISE CAN bus diagnostics
Use M.U.T.-IIISE to diagnose the CAN bus lines.
Is the check result normal?
Go to Step 3.
Repair the CAN bus lines (Refer to GROUP 54C - CAN Bus Diagnostics Table ). On completion, go to Step 2.
 
STEP 2. Diagnosis code recheck after resetting CAN bus lines
(1) Drive the vehicle at 20 km/h or more.
noteThe ABS warning lamp does not turn OFF in some cases unless the vehicle runs at 20 km/h or higher.
(2) Turn the ignition switch from the ON position to the LOCK (OFF) position.
Is diagnosis code No. C100A, 1015, 1020 or 102B set?
Go to Step 3.
This diagnosis is complete.
 
STEP 3. M.U.T.-IIISE data list
Check the following data list (Refer to ).
  • Item No.01: FL wheel speed sensor
  • Item No.02: FR wheel speed sensor
  • Item No.03: RL wheel speed sensor
  • Item No.04: RR wheel speed sensor
Is the check result normal?
Go to Step 10.
Go to Step 4.
 
STEP 4. Voltage measurement at the ASC-ECU connector (FL+, FL-, FR+, FR-, RL+, RL-, RR+, RR- terminal)
(1) Disconnect the connector, and measure at the wiring harness side.
(2) Turn the ignition switch to the "ON" position.
Code No.C100A is set
  • Measure the voltage between the ASC-ECU connector (FL+ terminal) and the body earth, and between the ASC-ECU connector (FL- terminal) and the body earth.
OK: 1 V or less
Code No.C1015 is set
  • Measure the voltage between the ASC-ECU connector (FR+ terminal) and the body earth, and between the ASC-ECU connector (FR- terminal) and the body earth.
OK: 1 V or less
Code No.C1020 is set
  • Measure the voltage between the ASC-ECU connector (RL+ terminal) and the body earth, and between the ASC-ECU connector (RL- terminal) and the body earth.
OK: 1 V or less
Code No.C102B is set
  • Measure the voltage between the ASC-ECU connector (RR+ terminal) and the body earth, and between the ASC-ECU connector (RR- terminal) and the body earth.
OK: 1 V or less
Is the check result normal?
Go to Step 5.
Go to Step 6.
 
STEP 5. Resistance measurement at ASC-ECU connector (FL+, FL-, FR+, FR-, RL+, RL-, RR+, RR- terminal)
Disconnect the connector, and measure at the wiring harness side.
Code No.C100A is set
  • Measure the resistance between the ASC-ECU connector (FL+ terminal) and the body earth, and between the ASC-ECU connector (FL- terminal) and the body earth.
OK: No continuity
Code No.C1015 is set
  • Measure the resistance between the ASC-ECU connector (FR+ terminal) and the body earth, and between the ASC-ECU connector (FR- terminal) and the body earth.
OK: No continuity
Code No.C1020 is set
  • Measure the resistance between the ASC-ECU connector (RL+ terminal) and the body earth, and between the ASC-ECU connector (RL- terminal) and the body earth.
OK: No continuity
Code No.C102B is set
  • Measure the resistance between the ASC-ECU connector (RR+ terminal) and the body earth, and between the ASC-ECU connector (RR- terminal) and the body earth.
OK: No continuity
Is the check result normal?
Go to Step 7.
Go to Step 6.
 
STEP 6. Check the wiring harness between the ASC-ECU connector terminal and the wheel speed sensor connector terminal.
Code No.C100A is set
  • Check of short circuit in FL+, FL- line between ASC-ECU connector and front wheel speed sensor (LH) connector.
Code No.C1015 is set
  • Check of short circuit in FR+, FR- line between ASC-ECU connector and front wheel speed sensor (RH) connector.
Code No.C1020 is set
  • Check of short circuit in RL+, RL- line between ASC-ECU connector and rear wheel speed sensor (LH) connector.
Code No.C102B is set
  • Check of short circuit in RR+, RR- line between ASC-ECU connector and rear wheel speed sensor (LH) connector.
Is the check result normal?
Replace the wheel speed sensor (Refer to <front> or <rear>).
Repair the connector(s) or wiring harness.
 
STEP 7. Voltage and current measurement at each wheel speed sensors connector
(1) Disconnect the wheel speed sensor connector, and measure at the wiring harness side.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between the power supply terminal of each wheel speed sensors and the body earth.
(4) Measure the output current at the special tool test harness (MB991709) to connect between the wheel speed sensor-side connector and the wiring harness connector (Refer to ).
OK:
  • <Voltage> System voltage
  • <Current> 5 - 9 mA or 11 - 17 mA
Is the check result normal?
Go to Step 10.
Go to Step 8.
 
STEP 8. Check the wiring harness between the ASC-ECU connector terminal and the wheel speed sensor connector terminal
Code No.C100A is set
  • Check of open circuit in FL+, FL- line between ASC-ECU connector and front wheel speed sensor (LH) connector.
Code No.C1015 is set
  • Check of open circuit in FR+, FR- line between ASC-ECU connector and front wheel speed sensor (RH) connector.
Code No.C1020 is set
  • Check of open circuit in RL+, RL- line between ASC-ECU connector and rear wheel speed sensor (LH) connector.
Code No.C102B is set
  • Check of open circuit in RR+, RR- line between ASC-ECU connector and rear wheel speed sensor (RH) connector.
Is the check result normal?
Go to Step 9.
Repair the connector(s) or wiring harness.
 
STEP 9. Check for wheel speed sensor as a single unit
Refer to .
Is the check result normal?
Go to Step 10.
Replace the wheel speed sensor (Refer to <front> or <rear>).
 
STEP 10. Check whether the diagnosis code is set again.
(1) Erase the diagnosis code.
(2) Drive the vehicle at 20 km/h or higher.
noteThe ABS warning lamp does not turn OFF in some cases unless the vehicle runs at 20 km/h or higher.
Is diagnosis code No. C100A, C1015, C1020 or C102B set?
Replace the hydraulic unit (integrated with ASC-ECU) (Refer to ).
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/How to Cope with Intermittent Malfunctions ).