[ Model - ECLIPSE CROSS / Year - 2018 ]
2018 / ECLIPSE CROSS / EC - Workshop Manual
42 -BODY > 42A-BODY > DOOR > WINDOW GLASS RUNCHANNEL AND DOOR OPENING WEATHERSTRIP > WINDOW GLASS RUNCHANNEL AND DOOR OPENING WEATHERSTRIP REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
 
 
 
 
Waterproof film removal steps 
•Door trim assembly (Refer to GROUP 52A, Door Trim )
>>B<<1.Waterproof film
Door speaker bracket removal steps <Vehicles with audio amplifier> 
•Door trim assembly (Refer to GROUP 52A, Door Trim )
>>B<<1.Waterproof film
2Door speaker bracket <Vehicles with audio amplifier>
Door working hole cover front and door working hole cover rear removal
•Door trim assembly (Refer to GROUP 52A, Door Trim )
>>B<<1.Waterproof film
3.Door working hole cover front
4.Door working hole cover rear
Door window glass runchannel removal
5.Door window glass runchannel
Door window glass runchannel rear removal
•Door trim assembly (Refer to GROUP 52A, Door Trim )
>>B<<1.Waterproof film
2Door speaker bracket <Vehicles with audio amplifier>
3.Door working hole cover front
4.Door working hole cover rear
6.Door window rear lower sash
7.Door window glass runchannel rear
Door sash moulding removal steps
8.Door sash moulding
Door beltline moulding removal steps
<<A>>9.Door beltline moulding
Door opening weatherstrip lower removal steps
10.Door opening weatherstrip lower
Door opening weatherstrip outer removal steps
<<B>>11.Door opening weatherstrip outer
Door opening weatherstrip inner removal steps
•Cowl side trim and front scuff plate (Refer to GROUP 52A, Interior Trim )
12.Door check connecting bolt
>>A<<13.Door opening weatherstrip inner
 
 
 
 
Waterproof film removal steps 
•Door trim assembly (Refer to GROUP 52A, Door Trim )
>>B<<1.Waterproof film
Door speaker bracket removal steps <Vehicles with audio amplifier> 
•Door trim assembly (Refer to GROUP 52A, Door Trim )
>>B<<1.Waterproof film
2.Door speaker bracket <Vehicles with audio amplifier>
Door working hole cover removal
•Door trim assembly (Refer to GROUP 52A , Door Trim )
>>B<<1.Waterproof film
3.Door working hole cover
Door sash moulding removal steps
4.Door sash moulding
Door beltline moulding removal steps
<<A>>5.Door beltline moulding
Door stationary window glass removal
•Door trim assembly (Refer to GROUP 52A, Door Trim )
5.Door window beltline moulding
6.Door stationary window glass weatherstrip
7.Door stationary window glass
Door window glass runchannel removal
8.Door window glass runchannel
Door window glass runchannel sash removal
•Door trim assembly (Refer to GROUP 52A, Door Trim )
>>B<<1.Waterproof film
2.Door speaker bracket <Vehicles with audio amplifier>
3.Door working hole cover
5.Door window beltline moulding
6.Door stationary window glass weatherstrip
8.Door window glass runchannel
9.Door window rear lower sash
Door opening weatherstrip outer removal steps
<<B>>10.Door opening weatherstrip outer
Door opening weatherstrip inner removal steps
•Cowl side trim and front scuff plate (Refer to GROUP 52A, Interior Trim )
11.Door check connecting bolt
>>A<<12.Door opening weatherstrip inner
 
 
REMOVAL SERVICE POINTS
 
 
<<A>> DOOR BELTLINE MOULDING REMOVAL
 
Insert a flat-tipped screwdriver as shown, and pry it in the direction shown to remove the door beltline moulding.
 

 
 
<<B>> DOOR OPENING WEATHERSTRIP OUTER REMOVAL
 
Make the tool as shown in the figure, and remove the weatherstrip from the door panel.
 
 
 
 
INSTALLATION SERVICE POINTS
 
 
>>A<< DOOR OPENING WEATHERSTRIP INNER INSTALLATION
 
Align the mark on the door opening weatherstrip inner with the notch at the vehicle bode side as shown.
 

 
 
>>B<< WATERPROOF FILM INSTALLATION
 
cautionWhen a waterproof film is applied, guide the butyl rubber tape under the inner panel drain hole.
Apply the specified adhesive to the water-proof film as shown in the figure and stick the film.
Specified sealant: 3M ATD Part No. 8625 or equivalent