[ Model - ECLIPSE CROSS / Year - 2018 ]
2018 / ECLIPSE CROSS / EC - Workshop Manual
52 -INTERIOR AND SUPPLEMENTAL RESTRAINT SYSTEM(SRS) > 52A-INTERIOR > TRIMS > INTERIOR TRIM > TRIM REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
 
 
<Floor trim>
 
 
 
Floor side trim removal steps
1.Front scuff plate
•Hood lock release handle connection (Refer to GROUP 42A - Hood ).
2.Cowl side trim
3.Rear seat anchor cover
4.Rear scuff plate
Footrest removal steps <RHD>
5.Footrest cap
6.Footrest
 
 
<Pillar trim>
 
 
Front pillar trim removal steps
•Door opening weatherstrip inner (Refer to GROUP 42A - Window Glass Runchannel and Door Opening Weatherstrip ).
<<A>>>>B<<1.Front pillar trim
<<A>>>>B<<2.Trim clip B
Centre pillar trim removal steps
3.Centre pillar cover inner
•Scuff plate (Refer to ).
•Door opening weatherstrip inner (Refer to GROUP 42A - Window Glass Runchannel and Door Opening Weatherstrip ).
4.Centre pillar trim lower
•Seat belt pre-tensioner mounting bolt (Refer to GROUP 52B - Seat Belt with Pre-tensioner ).
<<B>>>>A<<5.Centre pillar trim upper
 
 
<Quarter trim>
 
 
Removal steps
1.Parcel strap hook
2.Luggage room lamp assembly
•Rear end trim (Refer to ).
•Rear scuff plate (Refer to ).
•Door opening weatherstrip inner (Refer to GROUP 42A - Window Glass Runchannel and Door Opening Weatherstrip ).
3.Quarter trim lower assembly
4.Quarter trim hook
5.Rear seat belt clip
6.Quarter trim lower
7.Quarter panel silencer <some models>
<<C>>8.Quarter trim upper
9.Quarter trim bracket
 
 
<Cargo room trim>
 
 
Removal steps
1.Cargo floor cover
2.Cargo floor box lid
3.Cargo floor box
4.Rear end trim cap
•Tailgate opening weatherstrip (Refer to GROUP 42A - Tailgate ).
5.Rear end trim
 
 
REMOVAL SERVICE POINTS
 
 
<<A>> FRONT PILLAR TRIM / TRIM CLIP B REMOVAL
 
1. Remove the engagement between clip C on the upper side of the front pillar trim and the body.
 
2. Have clip B lifted from the front pillar trim.
3.
cautionIf clip B is removed from the body, replace it with a new one.
Slide the front pillar trim upward to remove it. At this time, do not remove clip B from the body.
 

 
 
<<B>> CENTRE PILLAR TRIM UPPER REMOVAL
 
1. Remove the engagement between the clip of the lower side of the centre pillar trim upper and the body.
2.
cautionBe careful not to rotate the trim extremely to prevent the headlining from getting wrinkles. Pull out the trim in the bottom direction while keeping the rotation amount to a minimum.
Rotate the trim lower side to the inside of the vehicle by using the upper side of the centre pillar trim upper as a fulcrum, and remove the engagement between the claw on the upper side of the trim and the body.
 

 
 
<<C>> QUARTER TRIM UPPER REMOVAL
1. Remove the anchor plate bolt of the rear seat belt LH/RH (Refer to GROUP 52B - Seat Belt with Pre-tensioner ).
2. Pull out the rear seat belt from the opening of the quarter trim upper.
 
 
 
INSTALLATION SERVICE POINTS
 
 
>>A<< CENTRE PILLAR TRIM UPPER INSTALLATION
 
1. Securely engage the claw on the lower side of the centre pillar trim upper to the hole on the body.
2. When the clip of the lower side of the centre pillar trim upper is difficult to catch, recheck whether the claw on the upper side of the trim is properly engaged.
 

 
 
>>B<< TRIM CLIP B / FRONT PILLAR TRIM INSTALLATION
When clip B is replaced with a new item
 
1. Attach clip B to the front pillar trim.
2. Attach the front pillar trim to the body.