[ Model - ECLIPSE CROSS / Year - 2018 ]
2018 / ECLIPSE CROSS / EC - Workshop Manual
52 -INTERIOR AND SUPPLEMENTAL RESTRAINT SYSTEM(SRS) > 52B-SUPPLEMENTAL RESTRAINT SYSTEM (SRS) > SEAT BELTS WITH PRE-TENSIONER > REMOVAL AND INSTALLATION OF SEAT BELTS WITH PRE-TENSIONER
REMOVAL AND INSTALLATION
caution
  • Disconnect the negative (-) battery terminal and wait for 60 seconds or more before starting work. Insulate the disconnected (-) terminal by wrapping the tape (Refer to the item 5 of Service Precautions ).
  • Never attempt to disassemble or repair the seat belt pre-tensioner. If faulty, replace it with new one(s).
  • Do not drop the seat belt with pre-tensioner or allow contact with water, grease or oil. If denting, cracking, or deformation is discovered, replace it with new one(s).
  • Do not place anything on top of seat belt pre-tensioner.
  • Do not store the seat belt with pre-tensioner in a place more than 90°C.
  • After the seat belt pre-tensioner deployment, replace with the new seat belt with pre-tensioner.
  • Put on gloves and safety glasses when handling a seat belt pre-tensioner once it has been used.
  • When discarding the seat belt with pre-tensioner, be sure to dispose it after deploying the seat belt pre-tensioner (Refer to ).
 
 
Pre-removal operation
Turn the ignition switch to the "LOCK" (OFF) position.
<Driver’s side and Passenger’s side (Vehicles without lap pre-tensioner)>
 
 
<Driver’s side and Passenger’s side (Vehicles with lap pre-tensioner)>
Removal steps
•Disconnect the negative (-) battery terminal.
•Centre pillar trim lower (Refer to GROUP 52A - Interior Trim ).
1.Front seat belt sash guide cover
2.Seat belt upper mounting bolt
3.Centre pillar trim upper (Refer to GROUP 52A - Interior Trim )
<<A>>4.Seat belt with pre-tensioner
5.Front seat belt anchor adjuster
6.Front seat belt plug <Vehicles with lap pre-tensioner>
Installation steps
>>A<<•Pre-installation inspection
•Disconnect the negative (-) battery terminal.
6.Front seat belt plug <Vehicles with lap pre-tensioner>
5.Front seat belt anchor adjuster
4.Seat belt with pre-tensioner
3.Centre pillar trim upper (Refer to GROUP 52A - Interior Trim )
2.Seat belt upper mounting bolt
1.Front seat belt sash guide cover
•Centre pillar trim lower (Refer to GROUP 52A - Interior Trim ).
•Connect the negative (-) battery terminal.
>>B<<•Post-installation inspection
 
<Rear>
Removal steps
•Disconnect the negative (-) battery terminal.
•Quarter trim upper (Refer to GROUP 52A - Interior Trim ).
<<A>>1.Seat belt with pre-tensioner
Installation steps
>>A<<•Pre-installation inspection
•Disconnect the negative (-) battery terminal.
1.Seat belt with pre-tensioner
•Quarter trim upper (Refer to GROUP 52A - Interior Trim ).
•Connect the negative (-) battery terminal.
>>B<<•Post-installation inspection
 
 
REMOVAL SERVICE POINT
 
 
<<A>> SEAT BELT WITH PRE-TENSIONER REMOVAL
 
 
1.
cautionWhen discarding the seat belt with pre-tensioner, discard after operating the seat belt pre-tensioner as specified in the service procedure (Refer to ).
Use the flat-tipped screwdriver to pull out the locking button of wiring harness side connector, and release the lock.
 
2. Use the flat-tipped screwdriver to pull out the locking button of wiring harness side connector, and release the lock.
 

 
 
 
INSTALLATION SERVICE POINTS
 
 
>>A<< PRE-INSTALLATION INSPECTION
1. Check the seat belt pre-tensioner before installation (Refer to ).
noteEven when installing a new seat belt with pre-tensioner, perform an inspection before the installation.
2.
cautionBe sure to turn the ignition key to the "LOCK" (OFF) position when connecting or disconnecting M.U.T.-IIISE.
Connect M.U.T.-IIISE to the diagnosis connector (16 pin).
3. Turn the ignition switch to the "ON" position.
4. Read the diagnosis code, and check that everything is normal except the pre-tensioner open circuit.
5. Turn the ignition switch to the "LOCK" (OFF) position.
 

 
 
>>B<< POST-INSTALLATION INSPECTION
cautionAfter the maintenance of the SRS air bag and seat belt with pre-tensioner is completed, be sure to delete the diagnosis code and check whether the SRS warning lamp lights up (Refer to ).
1. Turn the ignition switch to the "ON" position.
 
2. Check that the SRS warning lamp is illuminated for 6 to 8 seconds, and extinguished afterward.
3. If the lamp does not extinguish, perform the troubleshooting (Refer to ).
4. Check the seat belt operation. If the seat belt cannot be draw out, replace with a new seat belt with pre-tensioner.