[ Model - ECLIPSE CROSS / Year - 2018 ]
2018 / ECLIPSE CROSS / EC - Workshop Manual
52 -INTERIOR AND SUPPLEMENTAL RESTRAINT SYSTEM(SRS) > 52B-SUPPLEMENTAL RESTRAINT SYSTEM (SRS) > PASSENGER'S (FRONT) AIR BAG MODULE > PASSENGER'S (FRONT) AIR BAG MODULE REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
caution
  • Disconnect the negative (-) battery terminal and wait for 60 seconds or more before starting work. Insulate the disconnected (-) terminal by wrapping the tape (Refer to the item 5 of Service Precautions ).
  • Never attempt to disassemble or repair the air bag module. If faulty, replace it with new one.
  • Do not drop the air bag module or allow contact with water, grease or oil. If denting, cracking, or deformation is discovered, replace it with new one.
  • Store the air bag modules on a flat surface with the deployment surface facing up. Also, do not put anything on it.
  • Do not store the air bag module in a place more than 93°C.
  • When the air bags have been deployed, replace the and air bag module with new one.
  • Put on gloves and safety glasses when handling deployed air bags.
  • When discarding the air bag module, make sure to deploy the air bag before the disposal (Refer to ).
 
 
Pre-removal operation
Turn ignition switch to the "LOCK" (OFF) position.
 
Removal steps
•Disconnect the negative (-) battery terminal.
•Glovebox case assembly (Refer to GROUP 52A - Glove Box ).
<<A>>1.Passenger’s (front) air bag module connector
2.Bolts
•Instrument panel assembly (Refer to GROUP 52A - Instrument Panel Assembly ).
<<B>>3.Passenger’s (front) air bag module
Installation steps
•Connect the negative (-) battery terminal.
>>A<<•Pre-installation inspection
•Disconnect the negative (-) battery terminal.
3.Passenger’s (front) air bag module
•Instrument panel assembly (Refer to GROUP 52A - Instrument Panel Assembly ).
2.Bolts
1.Passenger’s (front) air bag module connector
•Glovebox case assembly (Refer to GROUP 52A - Glove Box ).
•Connect the negative (-) battery terminal.
>>B<<•Post-installation inspection
 
 
REMOVAL SERVICE POINTS
 
 
<<A>> PASSENGER'S (FRONT) AIR BAG MODULE CONNECTOR REMOVAL
 
Use the flat-tipped screwdriver to pull out the locking button of wiring harness side connector, and release the lock.
 

 
 
<<B>> PASSENGER'S (FRONT) AIR BAG MODULE REMOVAL
caution
  • Never use an electric tester to diagnose the air bag module circuit. Never attempt to disassemble the air bag module.
  • The removed passenger's air bag module should be stored in a clean, dry place with the deployment surface facing up.
  • When discarding the air bag module, discard after deploying the air bag as specified in the service procedure (Refer to ).
 
Insert a flat-tipped screwdriver or similar tool to the location shown in the figure. After disengaging the tabs, remove the passenger's (front) air bag module.
 
 
 
 
INSTALLATION SERVICE POINTS
 
 
>>A<< PRE-INSTALLATION INSPECTION
1. Before the installation, check the air bag module (Refer to ).
noteEven when installing a new air bag module, perform an inspection before the installation.
2.
cautionBe sure to turn the ignition key to the "LOCK" (OFF) position when connecting or disconnecting M.U.T.-IIISE.
Connect M.U.T.-IIISE to the diagnosis connector (16 pin).
3. Turn the ignition switch to the ON position.
4. Read the diagnosis code, and check that everything is normal except the air bag module open circuit.
5. Turn the ignition switch to the "LOCK" (OFF) position.
 
 
 
>>B<< POST-INSTALLATION INSPECTION
cautionAfter the maintenance of the SRS air bag and seat belt with pre-tensioner is completed, be sure to delete the diagnosis code and check whether the SRS warning lamp lights up (Refer to ).
1. Turn the ignition switch to the "ON" position.
 
2. Check that the SRS warning lamp is illuminated for 6 to 8 seconds, and extinguished afterward.
3. If the lamp does not extinguish, perform the troubleshooting (Refer to ).