DTC P0037 Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2) |
DTC P0038 Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2) |
DTC P0057 Oxygen Sensor Heater Control Circuit Low (Bank 2 Sensor 2) |
DTC P0058 Oxygen Sensor Heater Control Circuit High (Bank 2 Sensor 2) |


| DTC No. | DTC Detection Condition | Trouble Area |
| P0037 P0057 | Heater current is 0.25 A or less when the heater operates with more than 10.5 V positive battery voltage |
|
| P0038 P0058 | When heater operates, heater current exceeds 2.0 A (1 trip detection logic) |
|
| Related DTCs | P0037: Heated oxygen sensor heater (bank 1) range check (low current) P0038: Heated oxygen sensor heater (bank 1) range check (high current) P0057: Heated oxygen sensor heater (bank 2) range check (low current) P0058: Heated oxygen sensor heater (bank 2) range check (high current) |
| Required sensors / components | Heated oxygen sensor heater |
| Required sensors / components | Vehicle speed sensor (VSS) |
| Frequency of operation | Continuous |
| Duration | 0.3 seconds |
| MIL operation | Immediate |
| Sequence of operation | None |
| The monitor will run whenever these DTCs are not present | None |
| Battery voltage | 10.5 V or more |
| All heater is turned OFF and intrusive heating is operated when the following conditions are met | Conditions (a) and (b) |
| (a) Heater | ON |
| (b) Heater current | Less than 0.3 A |
| Battery voltage | 10.5 V or more |
| Engine | Running |
| Starter | OFF |
| Intrusive heating | Not operating |
| Battery voltage | 10.5 V or more |
| All heater is turned OFF and intrusive heating is operated when the following conditions are met | Conditions (a) and (b) |
| (a) Heater | ON |
| (b) Heater current | 2 A or more |
| HO2S heater current during intrusive heating | Less than 0.3 A (when battery voltage is 10.5 V or more) |
| HO2S heater current | 2 A or more |
| HO2S heater current during intrusive heating | More than 2 A |
| HO2S heater current | 0.4 to 1 A (at idle, warmed-up engine and +B: 11 to 14 V) |
| MID | TID | Scaling | Description of Test Value | Minimum Test Limit | Maximum Test Limit |
| $42 | $90 | Multiply by 0.001 (A) | Maximum sensor heater current | Minimum test limit | Maximum test limit |
| MID | TID | Scaling | Description of Test Value | Minimum Test Limit | Maximum Test Limit |
| $46 | $90 | Multiply by 0.001 (A) | Maximum sensor heater current | Minimum test limit | Maximum test limit |

| 1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the H6 or H8 Heated Oxygen (HO2) sensor connectors.
Measure the resistance of the HO2 sensor connector.
| Tester Connection | Specified Condition |
| HT (1) - +B (2) | 11 to 16 Ω at 20°C (68°F) |
| HT (1) - E1 (4) | 10 kΩ or higher |
Reconnect the HO2 sensor connectors.
|
| ||||
| OK | |
| 2.INSPECT EFI RELAY |
![]() |
Remove the EFI relay from the engine room relay block.
Measure the resistance of the EFI relay.
| Terminal Connection | Specified Condition |
| 3 - 5 | 10 kΩ or higher |
| 3 - 5 | Below 1 Ω (when battery voltage applied to terminals 1 and 2) |
Reinstall the EFI relay.
|
| ||||
| OK | |
| 3.INSPECT ECM (HT1B OR HT2B VOLTAGE) |
![]() |
Turn the ignition switch ON.
Measure the voltage of the E4 and E5 ECM connectors.
| Terminal Connection | Specified Condition |
| HT1B (E4-1) - Body ground | 9 to 14 V |
| HT2B (E5-5) - Body ground |
|
| ||||
| NG | |
| 4.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - EFI RELAY, HEATED OXYGEN SENSOR - ECM) |
![]() |
Turn the ignition switch OFF.
Disconnect the H6 or H8 oxygen sensor connectors.
Disconnect the E4 and E5 ECM connectors.
Measure the resistance.
| Terminal Connection | Specified Condition |
| HTL2 (H6-1) - HT1B (E4-1) | Below 1 Ω |
| HTR2 (H8-1) - HT2B (E5-5) | Below 1 Ω |
| Terminal Connection | Specified Condition |
| HTL2 (H6-1) or HT1B (E4-1) - Body ground | 10 kΩ or higher |
| HTR2 (H8-1) or HT2B (E5-5) - Body ground | 10 kΩ or higher |
Remove EFI relay from engine room R/B.
Measure the resistance.
| Tester Connection | Specified Condition |
| +B (H6-2) - EFI relay (3) | Below 1 Ω |
| +B (H8-2) - EFI relay (3) |
| Tester Connection | Specified Condition |
| +B (H6-2) or EFI relay (3) - Body ground | 10 kΩ or higher |
| +B (H8-2) or EFI relay (3) - Body ground |
Reconnect the ECM connectors.
Reconnect the oxygen sensor connectors.
Reinstall the EFI relay.
|
| ||||
| OK | ||
| ||