Home › ENGINE · 2UZ-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2120    Throttle / Pedal Position Sensor / Switch "D" Circuit

DTC    P2122    Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input

DTC    P2123    Throttle / Pedal Position Sensor / Switch "D" Circuit High Input

DTC    P2125    Throttle / Pedal Position Sensor / Switch "E" Circuit

DTC    P2127    Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input

DTC    P2128    Throttle / Pedal Position Sensor / Switch "E" Circuit High Input

DTC    P2138    Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation

for Preparation Click here

HINT:
These DTCs relate to the Accelerator Pedal Position (APP) sensor.


DESCRIPTION

HINT:
  1. This accelerator pedal position sensor is a non - contact type.
  2. This ETCS (Electronic Throttle Control System) does not use a throttle cable.

The Accelerator Pedal Position (APP) sensor is mounted on the accelerator pedal bracket and has 2 sensor circuits: VPA1 (main) and VPA2 (sub). The voltage, which is applied to terminals VPA1 and VPA2 of the ECM, varies between 0 V and 5 V in proportion to the operating angle of the accelerator pedal (throttle valve). A signal from VPA1 indicates the actual accelerator pedal opening angle (throttle valve opening angle) and is used for engine control. A signal from VPA2 conveys the status of the VPA1 circuit and is used to check the APP sensor itself.
The ECM monitors the actual accelerator pedal opening angle (throttle valve opening angle) through the signals from VPA1 and VPA2, and controls the throttle actuator according to these signals.

A115889E01


DTC No.
DTC Detection Condition
Trouble Area
P2120
Condition (a) continues for 0.5 second or more:
(a) VPA is 0.4 V or less when accelerator pedal is fully released, or VPA is 4.8 V or more
  1. Accelerator Pedal Position (APP) sensor
  2. ECM
P2122
Condition (a) continues for 0.5 second or more when accelerator pedal is fully released:
(a) VPA is 0.2 V or less
  1. APP sensor
  2. Open in VCPA circuit
  3. Open or ground short in VPA circuit
  4. ECM
P2123
Condition (a) continues for 2.0 seconds or more:
(a) VPA is 4.8 V or more
  1. APP sensor
  2. Open in EPA circuit
  3. ECM
P2125
Condition (a) continues for 0.5 second or more:
(a) (VPA2 is 0.5 V or less when accelerator pedal is fully released) or (VPA2 is 4.8 V or more and VPA is between 0.4 V and 3.45 V)
  1. APP sensor
  2. ECM
P2127
VPA2 1.2 V or less for 0.5 seconds or more when accelerator pedal fully released
  1. APP sensor
  2. Open in VCP2 circuit
  3. Open or ground short in VPA2 circuit
  4. ECM
P2128
Conditions (a) and (b) continue for 2.0 seconds or more
  1. (a) VPA2 4.8 V or more
  2. (b) VPA between 0.4 V and 3.45 V
  1. APP sensor
  2. Open in EPA2 circuit
  3. ECM
P2138
Condition (a) or (b) continues for 2.0 seconds or more
  1. (a) Difference between VPA and VPA2 0.02 V or less
  2. (b) VPA1 0.4 V or less and VPA2 1.2 V or less
  1. Short between VPA and VPA2 circuits
  2. APP sensor
  3. ECM

HINT:
After confirming DTC P2120, P2122, P2123, P2125, P2127, P2128 and P2138, use the intelligent tester or the OBD II scan tool to confirm the throttle valve opening percentage.

Trouble Area
Accelerator pedal position expressed as voltage
Accelerator pedal released
Accelerator pedal depressed
ACCEL POS #1
ACCEL POS #2
ACCEL POS #1
ACCEL POS #2
VC circuit open
0 to 0.2 V
0 to 0.2 V
0 to 0.2 V
0 to 0.2 V
VPA circuit open or ground short
0 to 0.2 V
1.2 to 2.0 V
0 to 0.2 V
3.4 to 5.3 V
VPA2 circuit open or ground short
0.5 to 1.1 V
0 to 0.2 V
2.6 to 4.5 V
0 to 0.2 V
E2 circuit open
4.5 to 5.5 V
4.5 to 5.5 V
4.5 to 5.5 V
4.5 to 5.5 V

HINT:
  1. Accelerator pedal positions are expressed as voltages.
  2. AP stands for Accelerator Pedal.


MONITOR DESCRIPTION

When VPA or VPA2 deviates from the standard, or the difference between the voltage outputs of the two sensors is less than threshold, the ECM concludes that there is a defect in the accelerator pedal position sensor. The ECM turns on the MIL and a DTC is set.
Example:
When the voltage output of the VPA is below 0.2 V or exceeds 4.8 V.

MONITOR STRATEGY


Related DTCs
P2120: Accelerator Pedal Position (APP) sensor 1 range check (fluctuating)
P2122: APP sensor 1 range check (low voltage)
P2123: APP sensor 1 range check (high voltage)
P2125: APP sensor 2 range check (fluctuating)
P2127: APP sensor 2 range check (low voltage)
P2128: APP sensor 2 range check (high voltage)
P2138: APP sensor range check (correlation)
Required Sensors/Components (Main)
APP sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
2.0 seconds
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None
Ignition switch
ON
Throttle actuator power
ON

TYPICAL MALFUNCTION THRESHOLDS


P2120: 
Either of the following conditions is met:
Condition 1 or 2
1. VPA1 voltage when VPA2 voltage is 0.04 V or more
0.4 V or less
2. VPA1 voltage
4.8 V or more

P2122: 
VPA1 voltage when VPA2 voltage is 0.04 V or more
0.4 V or less

P2123: 
VPA1 voltage
4.8 V or more

P2125: 
Either of the following conditions is met:
Condition 1 or 2
1. VPA2 voltage when VPA1 is 0.04 V or more
1.2 V or less
2. VPA2 voltage when VPA1 is 0.4 to 3.45 V
4.8 V or more

P2127: 
VPA2 voltage when VPA1 0.04 V or more
1.2 V or less

P2128: 
VPA2 voltage when VPA1 0.4 to 3.45 V
4.8 V or more

P2138: 
Either of following conditions is met:
Condition 1 or 2
Condition 1
-
Difference between VPA1 and VPA2 voltages
0.02 V or less
Condition 2
Condition (a) and (b)
(a) VPA1 voltage
0.4 V or less
(b) VPA2 voltage
1.2 V or less

COMPONENT OPERATING RANGE


VPA1 voltage
0.4 to 4.8 V
VPA2 voltage
1.2 to 4.8 V
Difference between VPA1 and VPA2 voltages
More than 0.02 V

FAIL-SAFE

The accelerator pedal position sensor has two (main and sub) sensor circuits. If a malfunction occurs in either of the sensor circuits, the ECM detects the abnormal signal voltage difference between the two sensor circuits and switches to limp mode. In limp mode, the remaining circuit is used to calculate the accelerator pedal opening to allow the vehicle to continue driving.
If both circuits malfunction, the ECM regards the opening angle of the accelerator pedal to be fully closed. In this case, the throttle valve will remain closed as if the engine is idling.
If a "pass" condition is detected and then the ignition switch is turned OFF, the fail-safe operation will stop and the system will return to normal condition.

WIRING DIAGRAM


A115926E02


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air/fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.READ VALUE OF INTELLIGENT TESTER (ACCEL POS #1 AND ACCEL POS #2)


    FI07052E06
  1. Connect the intelligent tester to the DLC3 with CAN VIM.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DATA LIST / ETCS / ACCEL POS #1 and ACCEL POS #2.

  1. Read the values displayed on the tester.

    Standard voltage:
    Accelerator Pedal
    ACCEL POS #1
    ACCEL POS #2
    Released
    0.5 to 1.1 V
    1.5 to 2.9 V
    Depressed
    2.5 to 4.6 V
    3.5 to 5.5 V



OK
Go to step 5
NG


2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)


    A115719E02
  1. Disconnect the A24 accelerator pedal position sensor connector.

  1. Disconnect the E8 ECM connector.

  1. Measure the resistance between the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    VPA1 (A24-6) - VPA (E8-18)
    Below 1 Ω
    EP1 (A24-5) - EPA (E8-20)
    VCP1 (A24-4) - VCPA (E8-26)
    VPA2 (A24-3) - VPA2 (E8-19)
    EP2 (A24-2) - EPA2 (E8-21)
    VCP2 (A24-1) - VCP2 (E8-27)

Standard resistance (Check for short):
Tester Connection
Specified Condition
VPA1 (A24-6) or VPA (E8-18) - Body ground
10 kΩ or higher
EP1 (A24-5) or EPA (E8-20) - Body ground
VCP1 (A24-4) or VCPA (E8-26) - Body ground
VPA2 (A24-3) or VPA2 (E8-19) - Body ground
EP2 (A24-2) or EPA2 (E8-21) - Body ground
VCP2 (A24-1) or VCP2 (E8-27) - Body ground

  1. Reconnect the ECM connector.

  1. Reconnect the accelerator pedal position sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT ECM (VCPA AND VCP2 VOLTAGE)


    A138089E01
  1. Disconnect the A24 APP sensor connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage of the E8 ECM connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    VCPA (E8-26) - EPA (E8-20)
    4.5 to 5.0 V
    VCP2 (E8-27) - EPA2 (E8-21)

  1. Reconnect the APP sensor connector.



NG
REPLACE ECM
OK


4.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY
  1. Replace accelerator pedal rod assembly .


NEXT


5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL POSITION SENSOR DTCS)
  1. Connect the intelligent tester to the DLC3 with CAN VIM.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Clear DTCs (Click here).

  1. Allow the engine to idle for 15 seconds.

  1. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.

  1. Read DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P2120, P2122, P2123, P2125, P2127, P2128 or P2138
    A
    No output
    B



B
SYSTEM OK
A

REPLACE ECM