DTC P2714 Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P2714 | ECM detects a malfunction on SLT (ON side) according to the revolution difference of the turbine and the output shaft, and also by the oil pressure. (2-trip detection logic) |
|
| Related DTCs | P2714: Shift solenoid valve SLT/ON malfunction |
| Required sensors/Components | Shift solenoid valve SLT, Valve body, ATF temperature sensor, Speed sensor (NT), Speed sensor (NO) |
| Frequency of operation | Continuous |
| Duration | Immediate |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever this DTC is not present. | None |
| Turbine speed sensor (NT) circuit | Not circuit malfunction |
| Output speed sensor (NO) circuit | Not circuit malfunction |
| TFT temperature sensor circuit | Not circuit malfunction |
| Shift solenoid valve S1 circuit | Not circuit malfunction |
| Shift solenoid valve S2 circuit | Not circuit malfunction |
| Shift solenoid valve SR circuit | Not circuit malfunction |
| Shift solenoid valve SL1 circuit | Not circuit malfunction |
| Shift solenoid valve SL2 circuit | Not circuit malfunction |
| Shift solenoid valve SLT circuit | Not circuit malfunction |
| ECT (Engine Coolant Temperature) sensor circuit | Not circuit malfunction |
| KCS sensor circuit | Not circuit malfunction |
| ETCS (Electric Throttle Control System) | Not system down |
| Transmission range | "D" |
| ECT | 40°C (104°F) or more |
| Spark advance from Max. retard timing by KCS control | 0°crankshaft angle or more |
| Engine | Starting |
| TFT temperature | 10°C (50°F) or more |
| Summation of C1 clutch heat generations | Specified value |
| 1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P2714) |
Connect the OBD II scan tool or the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and push the OBD II scan tool or the intelligent tester main switch ON.
When you use intelligent tester:
Select the item "DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES".
Read the DTCs using the OBD II scan tool or the intelligent tester.
| Display (DTC output) | Proceed to |
| Only "P2714" is output | A |
| "P2714" and other DTCs | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST BY INTELLIGENT TESTER (SHIFT SOLENOID VALVE SLT) |
Turn the ignition switch off.
Lift the vehicle up.
![]() |
Remove the test plug on the transmission case center right side and connect SST.
Lower the vehicle.
Fully apply the parking brake and chock the 4 wheels.
Connect the intelligent tester together with the CAN VIM (controller area network vehicle interface module) to the DLC3.
Start the engine.
Warm up the ATF (Automatic Transmission Fluid).
Measure the line pressure when the engine is idling.
Turn on the tester.
Select the item "DIAGNOSIS / OBD/MOBD / ECT / ACTIVE TEST / SOLENOID (SLT)".
Follow the instructions on the tester and perform the ACTIVE TEST.
Measure the line pressure with SST.
| Item | Test Details |
| LINE PRESS UP* | [Test Details] Operate the shift solenoid SLT and raise the line pressure. [Vehicle Condition]
|
|
| ||||
| OK | |
| 3.PERFORM RUNNING TEST |
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester together with the CAN VIM (controller area network vehicle interface module) to the DLC3.
Turn the ignition switch to the ON position.
Turn on the tester.
Select the item "DIAGNOSIS / OBD/MOBD / ECT / ACTIVE TEST".
Follow the instructions on the tester and read the ACTIVE TEST.
| Item | Test Details | Diagnostic Note |
| SHIFT | [Test Details] Operate the shift solenoid valve and set the each shift position by yourself. [Vehicle Condition]
| Possible to check the operation of the shift solenoid valves. |
Compare the ECM gear shift command and the actual gear position.
| ECM gear shift command | 1st | 2nd | 3rd | 4th | 5th | Proceed to | ||
| Actual gear position under malfunction | Shift solenoid S1 | Stuck ON | 1st | 2nd | 2nd | 1st | N*1
| A |
| Stuck OFF | 4th | 3rd | 3rd | 4th | 5th | |||
| Shift solenoid S2 | Stuck ON*2
| 2nd | 2nd | 3rd | 3rd | N*1
| B | |
| Stuck OFF*3
| 1st | 1st | 4th | 4th | 5th | |||
| Shift solenoid SL2 | Stuck ON | 1st | 2nd | 3rd | 4th | N*1
| C | |
| Stuck OFF | 1st | 2nd | 3rd | 4th | 5th | |||
| Shift solenoid SR | Stuck ON*4
| 1st | 2nd | 3rd | 4th | 5th | D | |
| Stuck OFF*5
| 1st | 2nd | 3rd | 4th | 4th | |||
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| A | |
| 4.INSPECT SHIFT SOLENOID VALVE S1 |
![]() |
Remove the shift solenoid valve S1.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition 20°C (68°F) |
| Solenoid Connector (S1) - Solenoid Body (S1) | 11 to 15 Ω |
Connect the positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body.
|
| ||||
| NG | ||
| ||
| 5.INSPECT SHIFT SOLENOID VALVE S2 |
![]() |
Remove the shift solenoid valve S2.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition 20°C (68°F) |
| Solenoid Connector (S2) - Solenoid Body (S2) | 11 to 15 Ω |
Connect the positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body.
|
| ||||
| NG | ||
| ||
| 6.INSPECT SHIFT SOLENOID VALVE SL2 |
![]() |
Remove the shift solenoid valve SL2.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition 20°C (68°F) |
| 1 - 2 | 5.0 to 5.6 Ω |
Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.
|
| ||||
| NG | ||
| ||
| 7.INSPECT SHIFT SOLENOID VALVE SR |
![]() |
Remove the shift solenoid valve SR.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition 20°C (68°F) |
| Solenoid Connector (SR) - Solenoid Body (SR) | 11 to 15 Ω |
Connect the positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body.
|
| ||||
| OK | |
| 8.INSPECT SHIFT SOLENOID VALVE SL1 |
![]() |
Remove the shift solenoid valve SL1.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition 20°C (68°F) |
| 1 - 2 | 5.0 to 5.6 Ω |
Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.
|
| ||||
| NG | ||
| ||
| 9.INSPECT SHIFT SOLENOID VALVE SLT |
![]() |
Remove the shift solenoid valve SLT.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition 20°C (68°F) |
| 1 - 2 | 5.0 to 5.6 Ω |
Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.
|
| ||||
| OK | |
| 10.INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
|
| ||||
| OK | |
| 11.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY |
Check the torque converter clutch assembly (Click here).
|
| ||||
| OK | ||
| ||