DTC P0450 Evaporative Emission Control System Pressure Sensor Malfunction |
DTC P0451 Evaporative Emission Control System Pressure Sensor Range / Performance |
DTC P0452 Evaporative Emission Control System Pressure Sensor / Switch Low Input |
DTC P0453 Evaporative Emission Control System Pressure Sensor / Switch High Input |
| DTC No. | Monitoring Items | Malfunction Detection Conditions | Trouble Area | Detection Timing | Detection Logic |
| P0450 | Pressure sensor voltage abnormal fluctuation | Sensor output voltage rapidly fluctuates beyond upper and lower malfunction thresholds for 0.5 second. |
|
| 1 trip |
| P0451 | Pressure sensor noising | Sensor output voltage fluctuates frequently in certain time period. |
|
| 2 trip |
| P0451 | Pressure sensor stuck | Sensor output voltage does vary in certain time period. |
| EVAP monitoring (ignition OFF) | 2 trip |
| P0452 | Pressure sensor voltage low | Sensor output voltage is less than 0.45 V for 0.5 second. |
|
| 1 trip |
| P0453 | Pressure sensor voltage high | Sensor output voltage is more than 4.9 V for 0.5 second. |
|
| 1 trip |
![]() |
| Related DTCs | P0450: Evaporative emission control system pressure sensor/switch chattering P0451: Evaporative emission control system pressure sensor noise P0451: Evaporative emission control system pressure sensor stuck P0452: Evaporative emission control system pressure sensor/switch low input P0453: Evaporative emission control system pressure sensor/switch high input |
| Required Sensors/Components | Canister pump module |
| Frequency of Operation | Once per driving cycle: P0451 sensor stuck Continuous: P0451 sensor noise, P0450, P0452 and P0453 |
| Duration | 0.5 seconds: P0450, P0452, P0453 15 seconds: P0451 sensor noise |
| MIL Operation | Immediate: P0450, P0452, P0453 2 driving cycles: P0451 |
| Sequence of Operation | None |
| The monitor will run whenever these DTCs are not present | None |
| Atmospheric pressure | 70 to 110 kPa (525 to 825 mmHg) |
| Battery voltage | 10.5 V or more |
| IAT | 4.4 to 35°C (40 to 95°F) |
| EVAP pressure sensor malfunction (P0450, P0452, P0453) | Not detected |
| Either of the following conditions is met | Condition 1 or 2 |
| 1. Time after key off | 5 or 7 or 9.5 hours |
| 2. Engine condition | Running |
| Atmospheric pressure | 70 to 110 kPa (525 to 825 mmHg) |
| Battery voltage | 10.5 V or more |
| IAT | 4.4 to 35°C (40 to 95°F) |
| EVAP pressure sensor malfunction (P0450, P0452, P0453) | Not detected |
| Time after key off | 5 or 7 or 9.5 hours |
| Battery voltage | 8 V or more |
| Ignition switch | ON |
| Starter | OFF |
| Frequency that EVAP pressure change is 0.3 kPa or more | 10 times or more for 10 sec. |
| EVAP pressure change during reference pressure measurement | Less than 0.65 kPa (4.9 mmHg) |
| EVAP pressure | Less than 42.11 kPa (316 mmHg), or more than 123.761 kPa (928 mmHg) |
| EVAP pressure | Less than 42.11 kPa (316 mmHg) |
| EVAP pressure | More than 123.761 kPa (928 mmHg) |
| 1.CONFIRM DTC AND EVAP PRESSURE |
Connect the intelligent tester to the DLC3 with CAN VIM.
Turn the ignition switch ON and turn the intelligent tester ON.
Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
Read the values.
Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DATA LIST / EVAP / VAPOR PRESS.
Read the EVAP pressure displayed on the intelligent tester.
| Display (DTC Output) | Test Result | Suspected Trouble Areas | Proceed to |
| P0451 | - |
| A |
| P0452 | Less than 45 kPa (338 mmHg) |
| B |
| P0453 | More than 120 kPa (900 mmHg) |
| C |
|
| ||||
|
| ||||
| B | |
| 2.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM) |
![]() |
Disconnect the E8 ECM connector.
Turn the ignition switch OFF.
Measure the resistance of the wire harness side connectors.
| Test Results | Suspected Trouble Areas | Proceed to |
| 10 Ω or less |
| A |
| 10 kΩ or more |
| B |
Reconnect the ECM connector.
|
| ||||
| A | |
| 3.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM) |
![]() |
Disconnect the L4 canister connector.
Disconnect the E8 ECM connector.
Measure the resistance of the wire harness side connectors.
| Test Results | Suspected Trouble Areas | Proceed to |
| 10 kΩ or more |
| A |
| 10 Ω or less |
| B |
Reconnect the canister connector.
Reconnect the ECM connector.
|
| ||||
|
| ||||
| 4.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM) |
![]() |
Disconnect the L4 canister connector.
Turn the ignition switch ON.
Measure the voltage of the canister pump module connector.
| Tester Connections | Specified Conditions |
| L4-4 - Body ground | 4.5 to 5.0 V |
| L4-3 - Body ground | 4.5 to 5.0 V |
Measure the resistance of the canister pump module connector.
| Tester Connections | Specified Conditions |
| L4-2 - Body ground | 100 Ω or less |
| Test Results | Suspected Trouble Areas | Proceed to |
| Voltage and resistance within standard ranges |
| A |
| Voltage and resistance outside standard ranges |
| B |
Connect the canister connector.
|
| ||||
| A | |
| 5.REPLACE CANISTER ASSEMBLY |
Replace canister assembly .
|
| ||||
| 6.REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
| ||||
| 7.REPLACE ECM |
Replace ECM (Click here).
| NEXT | |
| 8.CHECK WHETHER DTC OUTPUT RECURS (AFTER REPAIR) |
Connect the intelligent tester to the DLC3 with CAN VIM.
Turn the ignition switch ON and turn the intelligent tester ON.
Wait for at least 60 seconds.
Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DTC INFO / PENDING CODES.
| NEXT | ||
| ||