Home › BODY ELECTRICAL › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM

WIRELESS DOOR LOCK CONTROL SYSTEM > Only Wireless Control Function is Inoperative

for Preparation Click here


DESCRIPTION

The door control receiver receives a signal from the transmitter and sends this signal to the body ECU. Then, the body ECU controls operation of the door locks except the back door lock in response to this signal, while the body ECU sends a signal to the back door ECU at the same time. Receiving this signal, the back door ECU controls operation of the back door lock. Also, the back door ECU causes the back window to open, receiving a signal from the transmitter via the body ECU.

WIRING DIAGRAM


B062223E01


INSPECTION PROCEDURE

1.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS
  1. Check the wireless door lock control system (Click here).



OK
END
NG


2.CHECK TRANSMITTER BATTERY
  1. After replacing the transmitter battery with a new or normal one and then operating the transmitter LOCK/UNLOCK in the standard operation, check that the doors can lock and unlock even after operating it more than 3 times.

    NOTICE:
    Standard operation, herein, means operation by pressing the transmission switch for 1 second, directing the transmitter to the vehicle in a location that is 100 cm (39.37 in.) away from the driver side door outside handle in the right direction.



NG
Go to step 7
OK

REPLACE TRANSMITTER BATTERY 

3.CHECK WIRELESS DOOR LOCK BUZZER
  1. Check if the wireless door lock buzzer sounds.

    Result:

    Condition
    Proceed To
    Buzzer sounds
    A
    Buzzer does not sound
    Go to "No Answer-Back (Hazard Warning Light and Wireless Door Lock Buzzer)" (Click here)


A


4.SWITCH TO SELF DIAGNOSTIC MODE
  1. Switch to self-diagnostic mode using the intelligent tester.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch ON and turn the intelligent tester main switch on.

      HINT:
      Refer to the intelligent tester operator's manual for further details.

  1. Switch to self-diagnostic mode by performing the following (Manual operation):

    1. Put the vehicle under the initial condition (Click here). (Procedure "A")

    2. Insert the key into the ignition key cylinder and remove it. (Procedure "B")

    3. Within 5 seconds after the key is removed, insert the key into the ignition key cylinder again. (Procedure "C")

    4. Turn the ignition switch ON and turn it back OFF. (Procedure "D")

    5. Within 30 seconds of turning the ignition switch OFF again, perform the following 9 times: Turn the ignition switch ON and turn it back to OFF. (Procedure "E")

      HINT:
      1. Turning the ignition switch to the ON position after Procedure "E" has been completed will end the self-diagnostic mode.
      2. Do not lock or unlock doors during the self-diagnostic mode.

      NOTICE:
      If the self-diagnostic mode cannot be achieved, the system will return to normal mode.



    B110075E01
  1. Check that the system has switched to self-diagnostic mode by checking the sound of the wireless door lock buzzer.

    OK:
    The sound pattern of the wireless door lock buzzer should be the same as the patterns shown in the timing chart on the illustration.



NG
Go to step 9
OK


5.CHECK BY SELF DIAGNOSTIC MODE


  1. Check the diagnostic outputs when the door control transmitter switch is held down. The diagnostic outputs can be checked by the sound of the wireless door lock buzzer.


    B110076E16


    Result:

    Condition
    Proceed To
    Unmatched recognition code is output
    A
    Normal waves patterns from the wireless door lock buzzer are output for LOCK, UNLOCK, PANIC and BACK WINDOW
    B
    No diagnostic outputs are recorded
    C



B
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

C
Go to step 7
A


6.REGISTER RECOGNITION CODE
  1. Check that the system can switch to the rewrite mode or add mode and whether a recognition code can be registered.

    OK:
    The system can switch to the rewrite mode or add mode, and a recognition code can be registered.



NG
Go to step 8
OK

END 

7.CHECK RESPONSE OF DOOR CONTROL RECEIVER
  1. When a new or normal door control transmitter switch for the same type vehicle is held down, check that a diagnosis of unmatching recognition code is output.

    OK:
    Unmatched recognition code is output.



NG
Go to step 12
OK

REPLACE DOOR CONTROL TRANSMITTER 

8.REPLACE DOOR CONTROL RECEIVER
  1. Replace door control receiver with normal one.



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
OK

REPLACE DOOR CONTROL RECEIVER 

9.CONFIRM SELF DIAGNOSTIC MODE
  1. Confirm input method for self-diagnostic mode.

    Result:

    Condition
    Proceed To
    Method for changing system self-diagnostic mode works
    A
    Method for changing system self-diagnostic mode does not work
    B



B
Go to step 4
A


10.INSPECT UNLOCK WARNING SWITCH


    B110108E08
  1. Disconnect the unlock warning switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Switch pressed (Key set)
    Below 1 Ω
    1 - 2
    Switch free (Key removed)
    10 kΩ or higher



NG
REPLACE UNLOCK WARNING SWITCH
OK


11.CHECK HARNESS AND CONNECTOR (BODY ECU - UN-LOCK WARNING SWITCH)


    B062226E03
  1. Disconnect the body ECU (B6) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B6-14 (KSW) - K3-2
    Always
    Below 1 Ω
    B6-14 (KSW) - Body ground
    Always
    10 kΩor higher
    K3-2 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12.INSPECT DOOR CONTROL RECEIVER (POWER SOURCE)


    B059092E10
  1. Disconnect the D7 door control receiver connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Specified Condition
    D7-5 (+B) - Body ground
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


13.INSPECT DOOR CONTROL RECEIVER (E TERMINAL)


    B059092E10
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D7-1 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14.INSPECT DOOR CONTROL RECEIVER


    B051174E03
  1. Reconnect D7 receiver connector, and check the voltage according to the value(s) in the table below.

    Standard voltage:
    Symbols (Terminal No.)
    Condition
    Specified Condition
    RDA (D7-2) - Body ground
    Ignition switch OFF, no key in ignition key cylinder, all doors closed and each transmitter switch OFF → ON
    Below 1 V → Approx. 6 to 7 V → Below 1 V

    NOTICE:
    Check the output voltage with the bar graph display.



OK
Go to step 16
NG


15.CHECK HARNESS AND CONNECTOR (BODY ECU - DOOR CONTROL RECEIVER)


    B062225E03
  1. Disconnect the receiver (D7) connector and body ECU (B5) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D7-2 (RDA) - B5 -4 (RDA)
    Always
    Below 1 Ω
    D7-2 (RDA) - Body ground
    Always
    10 kΩor higher
    B5- 4 (RDA) - Body ground
    Always
    10 kΩor higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


16.REPLACE DOOR CONTROL RECEIVER
  1. Replace the door control receiver with normal one.

    OK:
    The system returns to normal operation.



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
OK

REPLACE DOOR CONTROL RECEIVER