NAVIGATION SYSTEM > Steering Pad Switch Circuit |

| 1.INSPECT RADIO AND NAVIGATION ASSEMBLY |
![]() |
Disconnect the radio and navigation assembly connector R10.
Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| SW1 - SWG | No switch is pushed | Approx. 100 kΩ |
| SW1 - SWG | SEEK+ switch: push | Approx. 0 Ω |
| SW1 - SWG | SEEK- switch: push | Approx. 0.3 kΩ |
| SW1 - SWG | VOL+ switch: push | Approx. 1 kΩ |
| SW1 - SWG | VOL- switch: push | Approx. 3.1 kΩ |
| SW2 - SWG | No switch is pushed | Approx. 100 kΩ |
| SW2 - SWG | MODE switch: push | Approx. 0 Ω |
| SW2 - SWG | VOICE switch: push | Approx. 3.1 kΩ |
| SW2 - SWG | ON HOOK switch: push | Approx. 0.3 kΩ |
| SW2 - SWG | OFF HOOK switch: push | Approx. 1 kΩ |
|
| ||||
| OK | ||
| ||
| 2.INSPECT STEERING PAD SWITCH ASSEMBLY |
Disconnect the steering pad switch assembly connector A.

Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| AU1 - EAU | No switch is pushed | Approx. 100 kΩ |
| AU1 - EAU | SEEK+ switch: push | Approx. 0 Ω |
| AU1 - EAU | SEEK- switch: push | Approx. 0.3 kΩ |
| AU1 - EAU | VOL+ switch: push | Approx. 1 kΩ |
| AU1 - EAU | VOL- switch: push | Approx. 3.1 kΩ |
| AU2 - EAU | No switch is pushed | Approx. 100 kΩ |
| AU2 - EAU | MODE switch: push | Approx. 0 Ω |
| AU2 - EAU | VOICE switch: push | Approx. 3.1 kΩ |
| AU2 - EAU | ON HOOK switch: push | Approx. 0.3 kΩ |
| AU2 - EAU | OFF HOOK switch: push | Approx. 1 kΩ |
|
| ||||
| OK | |
| 3.INSPECT SPIRAL CABLE |
![]() |
Disconnect the steering pad switch assembly and spiral cable connectors.
Measure the resistance according to the value(s) in the table below.
| Tester connection | Spiral Cable Position | Specified condition |
| EAU - EAU | Center | Below 1 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| AU1 - AU1 | Center | Below 1 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| AU2 - AU2 | Center | Below 1 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right |
|
| ||||
| OK | ||
| ||
| 4.INSPECT STEERING PAD SWITCH CABLE |
Disconnect the steering pad switch LH and the steering pad switch RH.

Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| B-1 - C-1 | Always | Below 1 Ω |
| B-2 - C-2 | Always | Below 1 Ω |
| B-3 - C-3 | Always | Below 1 Ω |
| B-4 - C-4 | Always | Below 1 Ω |
| B-5 - C-5 | Always | Below 1 Ω |
| B-6 - C-6 | Always | Below 1 Ω |
| B-7 - C-7 | Always | Below 1 Ω |
| B-8 - C-8 | Always | Below 1 Ω |
| B-1 - Body ground | Always | 10 kΩ or higher |
| B-2 - Body ground | Always | 10 kΩ or higher |
| B-3 - Body ground | Always | 10 kΩ or higher |
| B-4 - Body ground | Always | 10 kΩ or higher |
| B-5 - Body ground | Always | 10 kΩ or higher |
| B-6 - Body ground | Always | 10 kΩ or higher |
| B-7 - Body ground | Always | 10 kΩ or higher |
| B-8 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.INSPECT STEERING PAD SWITCH RH |
Reconnect the steering pad switch RH.

Measure the resistance according to the value(s) in the table below.
| Tester connection | Condition | Specified condition |
| AU2 (B-4) - EAU (B-2) | No switch is pushed | 10 kΩ or higher |
| AU2 (B-5) - EAU (B-3) | ||
| AU2 (B-5) - EAU (B-2) | ||
| AU2 (B-4) - EAU (B-3) | ||
| AU2 (B-4) - EAU (B-2) | VOICE switch: push | Approx. 3.2 kΩ |
| AU2 (B-5) - EAU (B-3) | ||
| AU2 (B-5) - EAU (B-2) | ||
| AU2 (B-4) - EAU (B-3) | ||
| AU2 (B-4) - EAU (B-2) | ON HOOK switch: push | Approx. 0.3 kΩ |
| AU2 (B-5) - EAU (B-3) | ||
| AU2 (B-5) - EAU (B-2) | ||
| AU2 (B-4) - EAU (B-3) | ||
| AU2 (B-4) - EAU (B-2) | OFF HOOK switch: push | Approx. 1 kΩ |
| AU2 (B-5) - EAU (B-3) | ||
| AU2 (B-5) - EAU (B-2) | ||
| AU2 (B-4) - EAU (B-3) |
|
| ||||
| OK | ||
| ||