Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1150/23    Occupant Classification System Malfunction

for Preparation Click here


DESCRIPTION

The occupant classification system circuit consists of the center airbag sensor assembly and the occupant classification ECU.
If the center airbag sensor assembly receives signals from the occupant classification ECU, it determines whether or not the front passenger airbag assembly and the front seat airbag assembly RH should be operated.
DTC B1150/23 is recorded when a malfunction is detected in the occupant classification system circuit.

DTC No.
DTC Detecting Condition
Trouble Area
B1150/23
  1. The center airbag sensor assembly receives a line short signal, open signal, short to ground signal or B+ short signal in the occupant classification system circuit for 2 seconds.
  2. Occupant classification ECU malfunction
  3. Center airbag sensor assembly malfunction
  1. Occupant classification ECU
  2. Center airbag sensor assembly
  3. Floor wire
  4. Seat wire No. 1

WIRING DIAGRAM


C116312E02


INSPECTION PROCEDURE

1.CHECK DTC (OCCUPANT CLASSIFICATION ECU)
  1. Turn the ignition switch to the ON position, and wait for at least 10 seconds.

  1. Using the intelligent tester, check the DTCs of the occupant classification ECU (Click here).

    OK:
    DTC is not output.



NG
GO TO OCCUPANT CLASSIFICATION SYSTEM
OK


2.CHECK DTC (CENTER AIRBAG SENSOR ASSEMBLY)


    C110461E01
  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1150/23 is not output.

    HINT:
    Codes other than code B1150/23 may be output at this time, but they are not related to this check.



NG
Go to step 3
OK

USE SIMULATION METHOD TO CHECK 

3.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the occupant classification ECU.

    OK:
    The connectors are connected.



NG
CONNECT CONNECTORS, THEN GO TO STEP 1
OK


4.CHECK OCCUPANT CLASSIFICATION ECU CIRCUIT (SHORT TO GROUND)


    C110462E30
  1. Disconnect the connectors from the center airbag sensor assembly and the occupant classification ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    Condition
    Specified condition
    O3-8 (FSR+) - Body ground
    Always
    1 MΩ or higher
    O3-4 (FSR-) - Body ground
    Always
    1 MΩ or higher



NG
Go to step 8
OK


5.CHECK OCCUPANT CLASSIFICATION ECU CIRCUIT (SHORT TO B+)


    C110462E30
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Voltage:
    Tester connection
    Condition
    Specified condition
    O3-8 (FSR+) - Body ground
    Ignition switch ON
    Below 1 V
    O3-4 (FSR-) - Body ground
    Ignition switch ON
    Below 1 V



NG
Go to step 9
OK


6.CHECK OCCUPANT CLASSIFICATION ECU CIRCUIT (SHORT)


    C110462E30
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    Condition
    Specified condition
    O3-8 (FSR+) - O3-4 (FSR-)
    Always
    1 MΩ or higher



NG
Go to step 10
OK


7.CHECK OCCUPANT CLASSIFICATION ECU CIRCUIT (OPEN)


    C111721E12
  1. with Side and curtain shield airbag:
    Using a service wire, connect A33-1 (FSR+) and A33-2 (FSR-) of connector "B".

  1. without Side and curtain shield airbag:
    Using a service wire, connect A34-3 (FSR+) and A34-10 (FSR-) of connector "B".

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    Condition
    Specified condition
    O3-8 (FSR+) - O3-4 (FSR-)
    Always
    Below 1 Ω



NG
Go to step 11
OK


8.CHECK FLOOR WIRE (SHORT TO GROUND)


    C110464E19
  1. Disconnect the floor wire connector from the seat wire No. 1.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    Condition
    Specified condition
    Bl1-1 (FSR+) - Body ground
    Always
    1 MΩ or higher
    Bl1-4 (FSR-) - Body ground
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK

REPAIR OR REPLACE SEAT WIRE NO. 1 

9.CHECK FLOOR WIRE (SHORT TO B+)


    C110464E19
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the floor wire connector from the seat wire No. 1.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Voltage:
    Tester connection
    Condition
    Specified condition
    Bl1-1 (FSR+) - Body ground
    Ignition switch ON
    Below 1 V
    Bl1-4 (FSR-) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE FLOOR WIRE
OK

REPAIR OR REPLACE SEAT WIRE NO. 1 

10.CHECK FLOOR WIRE (SHORT)


    C110464E19
  1. Disconnect the floor wire connector from the seat wire No. 1.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    Condition
    Specified condition
    Bl1-1 (FSR+) -Bl1-4 (FSR-)
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK

REPAIR OR REPLACE SEAT WIRE NO. 1 

11.CHECK FLOOR WIRE (OPEN)


    C111722E08
  1. Disconnect the floor wire connector from the seat wire No. 1.

    HINT:
    The service wire has already been inserted into connector "B".

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    Condition
    Specified condition
    Bl1-1 (FSR+) - Bl1-4 (FSR-)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE FLOOR WIRE
OK

REPAIR OR REPLACE SEAT WIRE NO. 1