Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1153/25    Seat Position Airbag Sensor Circuit Malfunction

for Preparation Click here


DESCRIPTION

The seat position airbag sensor circuit consists of the center airbag sensor assembly and the seat position airbag sensor.
DTC B1153/25 is recorded when a malfunction is detected in the seat position airbag sensor circuit.

DTC No.
DTC Detecting Condition
Trouble Area
B1153/25
  1. Open circuit in LSP+ wire harness or LSP- wire harness of seat position airbag sensor
  2. Short circuit in seat position airbag sensor wire harness (to ground)
  3. Short circuit in seat position airbag sensor wire harness (to B+)
  4. Seat position airbag sensor malfunction
  5. Center airbag sensor assembly malfunction
  1. Seat position airbag sensor
  2. Center airbag sensor assembly
  3. Floor wire No. 2

WIRING DIAGRAM


H044103E02


INSPECTION PROCEDURE

1.CHECK DTC


    C110471E03
  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1153/25 is not output.

    HINT:
    Codes other than code B1153/25 may be output at this time, but they are not related to this check.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK 

2.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly and the seat position airbag sensor.

    OK:
    The connectors are connected.



NG
CONNECT CONNECTORS, THEN GO TO STEP 1
OK


3.CHECK FLOOR WIRE NO. 2 (OPEN)


    C111723E05
  1. Disconnect the connectors from the center airbag sensor assembly and the seat position airbag sensor.

  1. with Side airbag:
    Using a service wire, connect A30-4 (LSP+) and A30-3 (LSP-) of connector "B".

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting.

  1. without Side airbag:
    Using a service wire, connect A31-3 (LSP+) and A31-8 (LSP-) of connector "B".

    NOTICE:
    Do not forcibly insert a service wire into the terminals of the connector when connecting.

  1. Measure the voltage according to the value(s) in the table below.

    Voltage:
    Tester connection
    Condition
    Specified condition
    B12-2 (LSP+) - B12-4 (LSP-)
    Always
    Below 1 V



NG
REPAIR OR REPLACE FLOOR WIRE NO. 2
OK


4.CHECK FLOOR WIRE NO. 2 (SHORT TO B+)


    C111660E30
  1. Disconnect the service wire from connector "B".

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position.

  1. Measure the voltage according to the value(s) in the table below.

    Voltage:
    Tester connection
    Condition
    Specified condition
    B12-2 (LSP+) - Body ground
    Ignition switch ON
    Below 1 V
    B12-4 (LSP-) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE FLOOR WIRE NO. 2
OK


5.CHECK FLOOR WIRE NO. 2 (SHORT TO GROUND)


    C111660E30
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    Condition
    Specified condition
    B12-2 (LSP+) - Body ground
    Always
    1 MΩ or higher
    B12-4 (LSP-) - Body ground
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE NO. 2
OK


6.CHECK FLOOR WIRE NO. 2 (SHORT)


    C111660E30
  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    Condition
    Specified condition
    B12-2 (SLP+) - B12-4 (LSP-)
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE NO. 2
OK


7.CHECK SEAT POSITION AIRBAG SENSOR


    C110471E04
  1. Connect the connectors to the seat position airbag sensor and the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1153/25 is not output.

    HINT:
    Codes other than code B1153/25 may be output at this time, but they are not related to this check.



NG
Go to step 8
OK

USE SIMULATION METHOD TO CHECK 

8.REPLACE SEAT POSITION AIRBAG SENSOR
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the seat position airbag sensor (Click here).

    HINT:
    Perform the inspection using parts from a normal vehicle if possible.


NEXT


9.CHECK CENTER AIRBAG SENSOR ASSEMBLY


    C110471E05
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1153/25 is not output.

    HINT:
    Codes other than code B1153/25 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK

END