DTC P1613 Secondary Air Injection Driver Malfunction |
| DTC No. | DTC Detection Condition | Trouble Area |
| P1613 | Either of following condition (a) or (b) is met:
|
|
| P1613 | Both of following conditions are met (1 trip detection logic):
|
|
| P1613 | Air injection control driver outputs abnormal duty signal (100 % duty signal) (1 trip detection logic) |
|
| Related DTCs | P1613: Secondary air injection system control module range check |
| Required sensors/components | Air injection control driver |
| Frequency of operation | Continuous |
| Duration | 3 seconds |
| MIL operation | Immediate |
| Sequence operation | None |
| The monitor will run whenever these DTCs are not present | None |
| Battery voltage | 8 V or more |
| Ignition switch | ON |
| Starter | OFF |
| Either of following conditions is met | Condition 1 or 2 |
| 1. Air pump | Not operating |
| 2. Air switching valve | Not operating |
| Battery voltage | 8 V or more |
| Ignition switch | ON |
| Starter | OFF |
| Air pump | Operating |
| Air switching valve | Operating |
| Battery voltage | 8 V or more |
| Ignition switch | ON |
| Starter | OFF |
| Battery voltage | 8 V or more |
| Ignition switch | ON |
| Starter | OFF |
| One of the following conditions is met | Condition 1, 2, 3 or 4 |
| 1. Diagnostic signal duty ratio from air injection control driver | 1 to 10 % |
| 2. Diagnostic signal duty ratio from air injection control driver | 30 % |
| 3. Diagnostic signal duty ratio from air injection control driver | 49 % |
| 4. Diagnostic signal duty ratio from air injection control driver | 91 to 99 % |
| Diagnostic signal duty ratio from air injection control driver | 70 to 90 % |
| Diagnostic signal duty ratio from air injection control driver | 0 % |
| Diagnostic signal duty ratio from air injection control driver | 100 % |
| Diagnostic signal duty ratio from air injection control driver | 70 to 90 % when secondary air injection system is operating and 0 % when secondary air injection system is not operating |
![]() |
![]() |
![]() |
| Item | Content |
| Terminal | CH1: AIDI - E1 |
| Equipment Setting | 5 V/DIV., 20 to 40 msec./DIV. |
| Condition | Idling |
| AID Diagnostic Signal Waveform | ECM Command | DTC (ECM Output) | Suspected Trouble Area |
| 100 % Duty Ratio See waveform 1 | Any Air Injection (AIR) System operation | P1613 |
|
| 0 % Duty Ratio See waveform 2 | AIR System: ON (Air pump ON, ASV ON) | P1613 |
|
| AIR System: OFF (Air pump OFF, ASV OFF) | - |
| |
| 20 % Duty Ratio See waveform 3 | Air Pump: ON | P0418 |
|
| Air Pump: OFF | P0418 |
| |
| 40 % Duty Ratio See waveform 4 | ASV: ON | P0412 |
|
| ASV: OFF | P0412 |
| |
| 80 % Duty Ratio See waveform 5 | AIR System: OFF (Air pump OFF, ASV OFF) | P1613 |
|
| AIR System: ON (Air pump ON, ASV ON) | - |
| |
| Excluding Above (excluding 0, 20, 40, 80, 100 % duty) | - | P1613 |
|
| Waveform 1 |
![]() |
| Waveform 2 |
![]() |
| Waveform 3 |
![]() |
| Waveform 4 |
![]() |
| Waveform 5 |
![]() |
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1613) |
Connect the intelligent tester to the DLC3 with CAN VIM.
Turn the ignition switch ON and turn the tester ON.
Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
Read DTCs.
| Display (DTC Output) | Proceed to |
| P1613 | A |
| P1613 and other DTCs | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST BY INTELLIGENT TESTER (AIDI VOLTAGE) |
![]() |
Start the engine and warm it up.
Turn the ignition switch OFF.
Connect the intelligent tester to the DLC3 with CAN VIM.
Turn the ignition switch ON and turn the tester ON.
Start the engine.
Enter the following menus: DIAGNOSIS / ENHANCED OBD II / SYSTEM CHECK / AIR INJ CHECK / AUTOMATIC.
Measure the voltage between AIDI terminal of the ECM connector and body ground when the air injection system is ON and OFF.
| Results | Suspected Trouble Areas | Proceed to |
| Fixed at Low (1.6 V or less) even when AIR system ON (Air pump ON, ASV ON) |
| A |
| Fixed at High (12 V or more) even when AIR system OFF (Air pump OFF, ASV OFF) |
| B |
Other than above:
|
| C |
|
| ||||
|
| ||||
| A | |
| 3.INSPECT ECM (AIRP AND AIRV VOLTAGE) |
![]() |
Turn the ignition switch ON.
Measure the voltage between terminal E8-25 (AIRP), E8-4 (AIRV) of the ECM connector and body ground.
| Tester Connection | Specified Condition |
| AIRP (E8-25) - Body ground | 10 V or more |
| AIRV (E8-4) - Body ground | 10 V or more |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER, AIR INJECTION CONTROL DRIVER - BODY GROUND) |
![]() |
Disconnect the A44 air injection driver connector.
Disconnect the E8 ECM connector.
Measure the resistance between the wire harness side connectors.
| Tester Connection | Specified Condition |
| SIP (A44-4) or AIRP (E8-25) - Body ground | 10 kΩ or higher |
| SIV (A44-3) or AIRV (E8-4) - Body ground | 10 kΩ or higher |
| E (A44-1) - Body ground | Below 1 Ω |
Measure the voltage between terminals DI (A44-2) and E(A44-1) of the air injection driver wire harness side connectors.
| Tester Connection | Specified Condition |
| DI (A44-2) - E (A44-1) | 9 V or more |
Reconnect air injection driver connector.
Reconnect ECM connector.
|
| ||||
| OK | ||
| ||
| 5.CHECK POWER SOURCE OF AIR INJECTION CONTROL DRIVER |
![]() |
Disconnect the A44 Air Injection Control Driver (AID) connector.
Turn the ignition switch ON.
Measure the voltage between the terminal +B (A44-5) and E (A44-1) of the AID connector.
| Tester Connection | Specified Condition |
| +B (A44-5) - E (A44-1) | 10 V or more |
|
| ||||
| OK | |
| 6.INSPECT AIR INJECTION CONTROL DRIVER (DI TERMINAL VOLTAGE) |
![]() |
Disconnect the A44 AID connector.
Turn the ignition switch ON.
Measure the voltage between the terminal A44-2 (DI) of the AID connector and body ground.
| Tester Connection | Specified Condition |
| DI (A44-2) - Body ground | 10 V or more |
Reconnect the AID connector.
|
| ||||
| NG | |
| 7.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER) |
![]() |
Disconnect the A44 air injection driver connector.
Disconnect the E8 ECM connector.
Check the resistance between the wire harness side connectors.
| Tester Connection | Specified Condition |
| DI (A44-2) - AIDI (E8-13) | Below 1 Ω |
| DI (A44-2) or AIDI (E8-13) - +B (A44-5) | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 8.CHECK HARNESS AND CONNECTOR (AIR INJECTION DRIVER - BODY GROUND) |
![]() |
Disconnect the A44 AID connector.
Measure the resistance between the terminal E (A44-1) of the AID connector and body ground.
| Tester Connection | Specified Condition |
| E (A44-1) - Body ground | Below 1 Ω |
Reconnect the AID connector.
|
| ||||
| OK | |
| 9.REPLACE AIR INJECTION CONTROL DRIVER |
Replace AID.
| NEXT | |
| 10.CHECK WHETHER DTC OUTPUT RECURS (DTC P1613) |
Connect the intelligent tester to the DLC3 with CAN VIM.
Turn the ignition switch ON and turn the tester ON.
Clear the DTCs (Click here).
Start the engine.
Perform ACTIVE TEST to operate the air injection system.
Enter the following menus: DIAGNOSIS / ENHANCED OBD II / SYSTEM CHECK / AIR INJ CHECK / AUTOMATIC.
After operating the secondary air injection system, confirm the pending codes of the secondary air injection system by entering the following menus: DIAGNOSIS / ENHANCED OBD II / DTC INFO / PENDING CODES.
|
| ||||
| OK | ||
| ||