Home › SUSPENSION & AXLE › AXLE › REAR AXLE SHAFT

REAR AXLE SHAFT > INSTALLATION

for Preparation Click here



1. INSTALL REAR AXLE SHAFT


    F042778E01
  1. Using SST and a press, install the rear axle shaft to the rear axle bearing assembly.

    SST
    09521-25011  



2. INSTALL REAR AXLE SHAFT SNAP RING


    F042773
  1. Using a snap ring expander, install a new rear axle shaft snap ring.



3. INSTALL REAR AXLE SHAFT OIL SEAL


    F042743E01
  1. Using SST and a hammer, install a new axle shaft oil seal.

    SST
    09950-60020   (09951-00770)
    09950-70010   (09951-07150)



4. INSTALL REAR AXLE SHAFT WITH BACKING PLATE


    F042741
  1. Install a new O-ring.

  1. Install the rear axle shaft with backing plate with the 4 nuts.

    Torque:
    123 N*m{ 1,254 kgf*cm , 91 ft.*lbf }



5. INSTALL PARKING BRAKE SHOE
  1. Install the shoe lever and the shim to the rear shoe with a new C-washer.



    R000343
  1. Using a feeler gauge, measure the clearance.

    Standard clearance:
    Less than 0.25 mm (0.0098 in.)

    If the clearance is not within the specification, replace the shim with one of the correct size.
    Shim Thickness
    Shim Thickness
    0.3 mm (0.012 in.)
    0.6 mm (0.024 in. )
    0.4 mm (0.016 in.)
    0.9 mm (0.035 in.)
    0.5 mm (0.020 in.)
    -



    F041705
  1. Apply the high temperature grease to the adjusting bolt and piece.

  1. Install the shoe adjusting screw set and the tension spring to the front and rear shoe.

  1. Install the 2 pins, 4 cups and 2 shoe hold-down springs.

  1. Connect the parking brake cable to the shoe lever.

  1. Install the front and rear parking brake shoe.



6. INSTALL PARKING BRAKE SHOE STRUT


7. INSTALL PARKING BRAKE SHOE STRUT COMPRESSION SPRING


8. INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING
  1. Using a needle nose pliers, install the 2 return tension springs.

    HINT:
    Install front side spring first, rear side spring next.



9. INSTALL REAR DISC


10. CONNECT REAR DISC BRAKE CALIPER ASSEMBLY


    F043124
  1. Apply the lithium soap base glycol grease to the sliding part of 2 cylinder slide pins.

  1. Install the disc brake cylinder assembly rear with 2 cylinder slide pins.

    Torque:
    88 N*m{ 897 kgf*cm , 65 ft.*lbf }



11. INSTALL REAR SPEED SENSOR


    F043113
  1. Install the rear speed sensor with the nut to the steering knuckle.

    Torque:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

    NOTICE:
    Make sure the sensor tip is clean.



    F043111
  1. Connect the speed sensor connector.



12. ADD RESERVOIR WITH BRAKE FLUID


13. BLEED MASTER CYLINDER


14. BLEED BRAKE LINE


15. INSPECT BRAKE FLUID LEVEL IN RESERVOIR


16. INSPECT BRAKE FLUID LEAKAGE


17. INSTALL REAR WHEEL

Torque:
112 N*m{ 1,142 kgf*cm , 83 ft.*lbf }



18. INSPECT AND ADJUST PARKING BRAKE LEVER TRAVEL

HINT:
(Click here)



19. INSPECT ABS SPEED SENSOR SIGNAL

HINT:
(Click here)