VEHICLE STABILITY CONTROL SYSTEM > TEST MODE PROCEDURE |
| TEST MODE (SIGNAL CHECK) PROCEDURE (SST CHECK WIRE) |
Turn the ignition switch off.
Check that the steering wheel is in the straight-ahead position and move the shift lever to the P position.
![]() |
Using SST, connect terminals TS and CG of the DLC3.
Turn the ignition switch to the ON position.
![]() |
Check that the ABS and VSC TRAC warning lights blink in test mode.
| Trouble Area | See procedure |
| TS and CG terminal circuit |
Click here
|
| ABS warning light circuit |
Click here or Click here
|
| VSC TRAC warning light circuit |
Click here or Click here
|
Start the engine.
Using a check wire, perform the ABS sensor (acceleration sensor, master cylinder pressure sensor, center diff. lock detection switch, L4 detection switch and speed sensor) and VSC sensor (yaw rate sensor and DAC operation switch) signal checks in test mode (ABS sensor: See procedure "A" to "F", VSC sensor: See procedure "G" to "I").
| ACCELERATION SENSOR SIGNAL CHECK (SST CHECK WIRE) (Procedure "A") |
![]() |
Check that the ABS warning light is blinking in test mode.
Keep the vehicle in a stationary condition on a level surface for 1 second or more.
| MASTER CYLINDER PRESSURE SENSOR SIGNAL CHECK (SST CHECK WIRE) (Procedure "B") |
![]() |
Check that the ABS warning light is blinking in test mode.
Leave the vehicle in a stationary condition and release the brake pedal for 1 second or more, and quickly depress the brake pedal with a force of 98 N (10 kgf, 22 lbf) or more for 1 second or more.
| CENTER DIFF. LOCK DETECTION SWITCH SIGNAL CHECK (4WD) (SST CHECK WIRE) (Procedure "C") |
![]() |
Check that the ABS warning light is blinking in test mode.
Check the center diff. lock switch.
Push the center diff. lock switch on to lock the center differential.
Push the center diff. lock switch off to unlock the center differential.
| L4 DETECTION SWITCH SIGNAL CHECK (4WD) (SST CHECK WIRE) (Procedure "D") |
![]() |
Check that the ABS warning light is blinking in test mode.
Check the 4WD control (L4) switch.
Turn the H-L switch to the L position to put the vehicle in L4 mode.
Turn the H-L switch to the H position to put the vehicle in H4 mode.
| SPEED SENSOR SIGNAL CHECK (SST CHECK WIRE) (Procedure "E") |
![]() |
Check that the ABS warning light is blinking in test mode.
Check the backward signal.
Drive the vehicle in reverse for more than 1 second at 2 mph (3 km/h) or higher.
Check the forward signal.
Drive the vehicle straight forward.
Drive the vehicle at a speed of 28 mph (45 km/h) or higher for several seconds and check that the ABS warning light goes off.
Stop the vehicle.
| READ DTC OF ABS SENSOR (SST CHECK WIRE) (Procedure "F") |
![]() |
Using SST, connect terminals TC and CG of the DLC3.
Read the number of blinks of the ABS warning light.

After the check, disconnect the SST from terminals TC and CG of the DLC3.
| YAW RATE SENSOR SIGNAL CHECK (SST CHECK WIRE) (Procedure "G") |
![]() |
Check that the VSC TRAC warning light is blinking in test mode.
Check the zero point voltage of the yaw rate sensor.
Keep the vehicle in a stationary condition on a level surface for 1 second or more.
Check the output of the yaw rate sensor and the direction of the steering angle sensor.
![]() |
Shift the shift lever to the D position and drive the vehicle at a vehicle speed of approximately 3 mph (5 km/h), turn the steering wheel either to the left or right 90° or more, and turn the vehicle through 180 degrees.
Stop the vehicle and shift the shift lever to the P position. Check that the skid control buzzer sounds for 3 seconds.
| DAC OPERATION SWITCH SIGNAL CHECK (4WD) (SST CHECK WIRE) (Procedure "H") |
![]() |
Check that the VSC TRAC warning light is blinking in test mode.
Check the DAC switch.
Push the DAC switch on.
Push the DAC switch off.
| READ DTC OF VSC SENSOR (SST CHECK WIRE) (Procedure "I") |
![]() |
Using SST, connect terminals TC and CG of the DLC3.
Read the number of blinks of the VSC TRAC warning light.

After performing the check, disconnect the SST from terminals TS and CG, TC and CG of the DLC3 and turn the ignition switch off.
| DTC OF SIGNAL CHECK FUNCTION (SST CHECK WIRE) (Procedure "J") |
| Code No. | Diagnosis | Trouble Area |
| C1271/71 | Low output voltage of right front speed sensor |
|
| C1272/72 | Low output voltage of left front speed sensor |
|
| C1273/73 | Low output voltage of right rear speed sensor |
|
| C1274/74 | Low output voltage of left rear speed sensor |
|
| C1275/75 | Abnormal change in output voltage of right front speed sensor | Speed sensor rotor |
| C1276/76 | Abnormal change in output voltage of left front speed sensor | Speed sensor rotor |
| C1277/77 | Abnormal change in output voltage of right rear speed sensor | Speed sensor rotor |
| C1278/78 | Abnormal change in output voltage of left rear speed sensor | Speed sensor rotor |
| C1279/79 | Acceleration sensor is faulty | Yaw rate and acceleration sensor |
| C1281/81 | Master cylinder pressure sensor output signal is faulty | Master cylinder pressure sensor |
| C1282/82 (*1) | Center differential lock position switch malfunction | Center diff. lock switch |
| C1283/83 (*1) | L4 position switch malfunction | 4WD control (L4) switch |
| Code No. | Diagnosis | Trouble Area |
| C0371/71 | Yaw rate sensor output signal malfunction | Yaw rate and acceleration sensor |
| C1379/74 | Malfunction in DAC operation switch | DAC switch |
| TEST MODE (SIGNAL CHECK) PROCEDURE (INTELLIGENT TESTER) |
Turn the ignition switch off.
Check that the steering wheel is in the straight-ahead position and move the shift lever to the P position.
![]() |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Operate the intelligent tester in test mode ("SIGNAL CHECK").

![]() |
Check that the ABS and VSC TRAC warning lights blink in test mode.
| Trouble Area | See procedure |
| TS and CG terminal circuit |
Click here
|
| ABS warning light |
Click here or Click here
|
| VSC TRAC warning light |
Click here or Click here
|
Start the engine.
Using the intelligent tester, perform the ABS sensor (acceleration sensor, master cylinder pressure sensor, center diff. lock detection switch, L4 detection switch and speed sensor) and VSC sensor (yaw rate sensor and DAC operation switch) signal checks in test mode (ABS sensor: See procedure "K" to "P", VSC sensor: See procedure "Q" to "S").
| ACCELERATION SENSOR SIGNAL CHECK (INTELLIGENT TESTER) (Procedure "K") |
![]() |
Check that the ABS warning light is blinking in test mode.
Keep the vehicle in the stationary condition on a level surface for 1 second or more.
| MASTER CYLINDER PRESSURE SENSOR SIGNAL CHECK (INTELLIGENT TESTER) (Procedure "L") |
![]() |
Check that the ABS warning light is blinking in test mode.
Leave the vehicle in a stationary condition and release the brake pedal for 1 second or more, and quickly depress the brake pedal with a force of 98 N (10 kgf, 22 lbf) or more for 1 second or more.
| CENTER DIFF. LOCK DETECTION SWITCH SIGNAL CHECK (4WD) (INTELLIGENT TESTER) (Procedure "M") |
![]() |
Check that the ABS warning light is blinking in test mode.
Check the center diff. lock switch.
Push the center diff. lock switch on to lock the center differential.
Push the center diff. lock switch off to unlock the center differential.
| L4 DETECTION SWITCH SIGNAL CHECK (4WD) (INTELLIGENT TESTER) (Procedure "N") |
![]() |
Check that the ABS warning light is blinking in test mode.
Check the 4WD control (L4) switch.
Turn the H-L switch to the L position to put the vehicle in L4 mode.
Turn the H-L switch to the H position to put the vehicle in H4 mode.
| SPEED SENSOR SIGNAL CHECK (INTELLIGENT TESTER) (Procedure "O") |
![]() |
Check that the ABS warning light is blinking in test mode.
Check the backward signal.
Drive the vehicle in reverse for more than 1 second at 2 mph (3 km/h) or higher.
Check the forward signal.
Drive the vehicle straight forward. Drive the vehicle at a speed of 28 mph (45 km/h) or higher for several seconds and check that the ABS warning light goes off.
Stop the vehicle.
| READ DTC OF ABS SENSOR (INTELLIGENT TESTER) (Procedure "P") |
Read the DTC(s) by following the tester screen.
| YAW RATE SENSOR SIGNAL CHECK (INTELLIGENT TESTER) (Procedure "Q") |
![]() |
Check that the VSC TRAC warning light is blinking in test mode.
Check the zero point voltage of the yaw rate sensor.
Keep the vehicle in a stationary condition on a level surface for 1 second or more.
Check the output of the yaw rate sensor and the direction of the steering angle sensor.
![]() |
Shift the shift lever to the D position and drive the vehicle at a vehicle speed of approximately 3 mph (5 km/h), turn the steering wheel either to the left or right 90° or more, and turn the vehicle through 180 degrees.
Stop the vehicle and shift the shift lever to the P position. Check that the skid control buzzer sounds for 3 seconds.
| DAC OPERATION SWITCH SIGNAL CHECK (4WD) (INTELLIGENT TESTER) (Procedure "R") |
![]() |
Check that the VSC TRAC warning light is blinking in test mode.
Check the DAC switch.
Push the DAC switch on.
Push the DAC switch off.
| READ DTC OF VSC SENSOR (INTELLIGENT TESTER) (Procedure "S") |
Read the DTC(s) by following the tester screen.
| DTC OF SIGNAL CHECK FUNCTION (INTELLIGENT TESTER) (Procedure "T") |
| Code No. | Diagnosis | Trouble Area |
| C1271/71 | Low output voltage of right front speed sensor |
|
| C1272/72 | Low output voltage of left front speed sensor |
|
| C1273/73 | Low output voltage of right rear speed sensor |
|
| C1274/74 | Low output voltage of left rear speed sensor |
|
| C1275/75 | Abnormal change in output voltage of right front speed sensor | Speed sensor rotor |
| C1276/76 | Abnormal change in output voltage of left front speed sensor | Speed sensor rotor |
| C1277/77 | Abnormal change in output voltage of right rear speed sensor | Speed sensor rotor |
| C1278/78 | Abnormal change in output voltage of left rear speed sensor | Speed sensor rotor |
| C1279/79 | Acceleration sensor is faulty | Yaw rate and acceleration sensor |
| C1281/81 | Master cylinder pressure sensor output signal is faulty | Master cylinder pressure sensor |
| C1282/82 (*1) | Center differential lock position switch malfunction | Center diff. lock switch |
| C1283/83 (*1) | L4 position switch malfunction | 4WD control (L4) switch |
| Code No. | Diagnosis | Trouble Area |
| C0371/71 | Yaw rate sensor output signal malfunction | Yaw rate and acceleration sensor |
| C1379/74 | Malfunction in DAC operation switch | DAC switch |