Home › DRIVE LINE ยท DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY

REAR DIFFERENTIAL CARRIER ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL REAR DIFFERENTIAL CARRIER ASSEMBLY


    C030284
  1. Clean the contact surfaces of the rear differential carrier assembly and the rear axle housing assembly.

  1. Install the new rear differential carrier gasket and the differential carrier assembly with the 10 nuts and 10 washers.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



2. INSTALL REAR AXLE SHAFT WITH BACKING PLATE


    F042741
  1. Install a new O-ring.

  1. Install the rear axle shaft with backing plate with the 4 nuts.

    Torque:
    123 N*m{ 1,254 kgf*cm , 91 ft.*lbf }



3. INSTALL PARKING BRAKE SHOE
  1. Install the shoe lever and the shim to the rear shoe with a new C-washer.



    R000343
  1. Using a feeler gauge, measure the clearance.

    Standard clearance:
    Less than 0.25 mm (0.0098 in.)

    If the clearance is not within the specification, replace the shim with one of the correct size.
    Shim Thickness
    Shim Thickness
    0.3 mm (0.012 in.)
    0.6 mm (0.024 in. )
    0.4 mm (0.016 in.)
    0.9 mm (0.035 in.)
    0.5 mm (0.020 in.)
    -



    F041705
  1. Apply the high temperature grease to the adjusting bolt and piece.

  1. Install the shoe adjusting screw set and the tension spring to the front and rear shoe.

  1. Install the 2 pins, 4 cups and 2 shoe hold-down springs.

  1. Connect the parking brake cable to the shoe lever.

  1. Install the front and rear parking brake shoe.



4. INSTALL PARKING BRAKE SHOE STRUT LH


5. INSTALL PARKING BRAKE SHOE STRUT COMPRESSION SPRING


6. INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING
  1. Using a needle nose pliers, install the 2 return tension springs.

    HINT:
    Install front side spring first, rear side spring next.



7. INSTALL REAR DISC
  1. Align the matchmarks and install the rear disc.



8. CONNECT REAR DISC BRAKE CALIPER ASSEMBLY LH
  1. Install the rear disc brake caliper assembly LH with the 2 bolts.

    Torque:
    88 N*m{ 897 kgf*cm , 65 ft.*lbf }



9. CONNECT REAR DISC BRAKE CALIPER ASSEMBLY RH
  1. Install the rear disc brake caliper assembly RH with the 2 bolts.

    Torque:
    88 N*m{ 897 kgf*cm , 65 ft.*lbf }



10. CONNECT REAR SPEED SENSOR LH


    F043113
  1. Install the rear speed sensor with the nut to the steering knuckle.

    Torque:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

    NOTICE:
    Make sure the sensor tip is clean.



    F043111
  1. Connect the speed sensor connector.



11. CONNECT REAR SPEED SENSOR RH

HINT:
Install the RH side by following the same procedures as the LH side.



12. INSTALL PROPELLER SHAFT ASSEMBLY
See procedure 
Vehicle Type
Proceed to
2WD
Click here
4WD
Click here


13. FILL UP RESERVOIR WITH BRAKE FLUID


14. BLEED MASTER CYLINDER


15. BLEED BRAKE LINE


16. BLEED BRAKE FLUID LEVEL IN RESERVOIR


17. CHECK FOR BRAKE FLUID LEAKAGE


18. FILL UP DIFFERENTIAL OIL


    D025304E03
  1. Stop the vehicle on a level place.

  1. Remove the differential filler plug and gasket.

  1. Check that the oil level is within 5mm (0 to 0.20 in.) of the bottom of the filler plug opening.

    NOTICE:
    1. Excessively large or small quantities of oil may cause problems.
    2. After replacing the oil, drive the vehicle and check the oil level again.

    HINT:
    If necessary, fill the rear differential carrier assembly with hypoid gear oil.

    Oil grade:
    Hypoid gear oil API GL-5
    Recommended viscosity:
    Above -18°C (0°F) SAE 90
    Below -18°C (0°F) SAE 80W or 80W-90

    Capacity:
    Front differential carrier assembly:
    1.35 to 1.45 litters
    (1.43 to 1.53 US qts, 1.19 to 1.27 lmp. qts)
    Rear differential carrier assembly
    3.00 to 3.10 litters
    (3.17 to 3.27 US qts, 2.64 to 2.72 lmp. qts)

  1. Check for oil leakage if the oil level is low.

  1. Install the differential filler plug and a new gasket.

    Torque:
    Front differential carrier assembly:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }
    Rear differential carrier assembly:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



19. INSPECT DIFFERENTIAL OIL


    D025304E03
  1. Stop the vehicle on a level place.

  1. Remove the differential filler plug and gasket.

  1. Check that the oil level is within 5mm (0 to 0.20 in.) of the bottom of the filler plug opening.

    NOTICE:
    1. Excessively large or small quantities of oil may cause problems.
    2. After replacing the oil, drive the vehicle and check the oil level again.

    HINT:
    If necessary, fill the rear differential carrier assembly with hypoid gear oil.

    Oil grade:
    Hypoid gear oil API GL-5
    Recommended viscosity:
    Above -18°C (0°F) SAE 90
    Below -18°C (0°F) SAE 80W or 80W-90

    Capacity:
    Front differential carrier assembly:
    1.35 to 1.45 litters
    (1.43 to 1.53 US qts, 1.19 to 1.27 lmp. qts)
    Rear differential carrier assembly
    3.00 to 3.10 litters
    (3.17 to 3.27 US qts, 2.64 to 2.72 lmp. qts)

  1. Check for oil leakage if the oil level is low.

  1. Install the differential filler plug and a new gasket.

    Torque:
    Front differential carrier assembly:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }
    Rear differential carrier assembly:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



20. INSTALL REAR WHEEL

Torque:
112 N*m{ 1,142 kgf*cm , 83 in.*lbf }



21. INSPECT AND ADJUST PARKING BRAKE LEVER TRAVEL

HINT:



22. INSPECT CHECK ABS SENSOR SIGNAL

HINT:
(Click here)