Home › DRIVE LINE ยท DIFFERENTIAL › 2UZ-FE FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD)

2UZ-FE FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD) > INSTALLATION

for Preparation Click here



1. INSTALL FRONT DIFFERENTIAL CARRIER ASSEMBLY


    C097020
  1. Install the No. 1 mounting support with the 3 bolts.

    Torque:
    186 N*m{ 1,900 kgf*cm , 137 ft.*lbf }

  1. Install the No. 2 mounting support with the 2 bolts.

    Torque:
    160 N*m{ 1,630 kgf*cm , 118 ft.*lbf }

  1. Install the No. 3 front differential support with the 2 bolts.

    Torque:
    108 N*m{ 1,100 kgf*cm , 80 ft.*lbf }

  1. Support the front differential with a jack.

  1. Install the 2 front mounting bolts and nuts.

    Torque:
    137 N*m{ 1,400 kgf*cm , 101 ft.*lbf }

  1. Install the No. 1 front differential mount nut.

    Torque:
    87 N*m{ 887 kgf*cm , 64 ft.*lbf }

  1. Install the front differential breather tube bracket with the bolt.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Lower the jack.



2. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH


F042771
  1. Coat the spline of the inboard joint shaft assembly with ATF.

  1. Align the shaft splines and install the drive shaft with a brass bar and hammer.

    NOTICE:
    1. Set the snap ring with the opening side facing downward.
    2. Be careful not to damage the oil seal.

    HINT:
    Whether the inboard joint shaft is in contact with the pinion shaft or not can be confirmed from the sound or feeling when driving it.



3. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



4. INSTALL NO. 1 FRONT SUSPENSION ARM SUB-ASSEMBLY LOWER LH


    G020160
  1. Fully tighten the bolt and the nut.

    Torque:
    135 N*m{ 1,380 kgf*cm , 100 ft.*lbf }



5. INSTALL NO. 1 FRONT SUSPENSION ARM SUB-ASSEMBLY LOWER RH


6. INSTALL TIE ROD END SUB-ASSEMBLY LH
  1. Connect the tie rod end to the steering knuckle arm.

  1. Install the nut and cotter pin.

    Torque:
    91 N*m{ 928 kgf*cm , 67 ft.*lbf }



7. INSTALL TIE ROD END SUB-ASSEMBLY RH

HINT:
Install the RH side by the same procedures with the LH side.



8. INSTALL FRONT SPEED SENSOR LH


    F043112
  1. Using a hexagon wrench (5 mm), install the front speed sensor with the bolt to the steering knuckle.

    SST
    99999-60011  

    Torque:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

    NOTICE:
    Make sure the sensor tip is clean.



    F044160
  1. Connect the speed sensor connector.



9. INSTALL FRONT SPEED SENSOR RH

HINT:
Use the same procedure as for the LH side.



10. INSTALL FRONT STABILIZER LINK ASSEMBLY LH


    G020161
  1. Install the front stabilizer link assembly LH with the 2 nuts.

    HINT:
    If the ball joint turns together with the nut, use a hexagon (6 mm) wrench to hold the stud.



11. INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



12. INSTALL FRONT AXLE HUB LH NUT


    F042732
  1. Install the hub nut.

    Torque:
    235 N*m{ 2,396 kgf*cm , 173 ft.*lbf }

  1. Install the adjusting cap and cotter pin.



13. INSTALL FRONT AXLE HUB RH NUT

HINT:
Use the same procedure as for the LH side.



14. INSTALL FRONT PROPELLER SHAFT ASSEMBLY


    C098708E06
  1. Align the matchmarks on the yoke and differential flange.

  1. Install the propeller shaft assembly with the 4 bolts, 4 nuts and 4 washers.

    Torque:
    88 N*m{ 897 kgf*cm , 65 ft.*lbf }



    C098709E05
  1. Align the matchmarks on the yoke and transfer flange.

  1. Install the propeller shaft assembly with the 4 nuts and 4 washers.

    Torque:
    88 N*m{ 897 kgf*cm , 65 ft.*lbf }



15. FILL UP DIFFERENTIAL OIL


    D025304E03
  1. Stop the vehicle on a level place.

  1. Remove the differential filler plug and gasket.

  1. Check that the oil level is within 5mm (0 to 0.20 in.) of the bottom of the filler plug opening.

    NOTICE:
    1. Excessively large or small quantities of oil may cause problems.
    2. After replacing the oil, drive the vehicle and check the oil level again.

    HINT:
    If necessary, fill the rear differential carrier assembly with hypoid gear oil.

    Oil grade:
    Hypoid gear oil API GL-5
    Recommended viscosity:
    Above -18°C (0°F) SAE 90
    Below -18°C (0°F) SAE 80W or 80W-90

    Capacity:
    Front differential carrier assembly:
    1.35 to 1.45 litters
    (1.43 to 1.53 US qts, 1.19 to 1.27 lmp. qts)
    Rear differential carrier assembly
    3.00 to 3.10 litters
    (3.17 to 3.27 US qts, 2.64 to 2.72 lmp. qts)

  1. Check for oil leakage if the oil level is low.

  1. Install the differential filler plug and a new gasket.

    Torque:
    Front differential carrier assembly:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }
    Rear differential carrier assembly:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



16. INSPECT DIFFERENTIAL OIL


    D025304E03
  1. Stop the vehicle on a level place.

  1. Remove the differential filler plug and gasket.

  1. Check that the oil level is within 5mm (0 to 0.20 in.) of the bottom of the filler plug opening.

    NOTICE:
    1. Excessively large or small quantities of oil may cause problems.
    2. After replacing the oil, drive the vehicle and check the oil level again.

    HINT:
    If necessary, fill the rear differential carrier assembly with hypoid gear oil.

    Oil grade:
    Hypoid gear oil API GL-5
    Recommended viscosity:
    Above -18°C (0°F) SAE 90
    Below -18°C (0°F) SAE 80W or 80W-90

    Capacity:
    Front differential carrier assembly:
    1.35 to 1.45 litters
    (1.43 to 1.53 US qts, 1.19 to 1.27 lmp. qts)
    Rear differential carrier assembly
    3.00 to 3.10 litters
    (3.17 to 3.27 US qts, 2.64 to 2.72 lmp. qts)

  1. Check for oil leakage if the oil level is low.

  1. Install the differential filler plug and a new gasket.

    Torque:
    Front differential carrier assembly:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }
    Rear differential carrier assembly:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



17. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Install the No. 1 engine under cover sub-assembly with the 4 bolts.



18. INSTALL REAR ENGINE UNDER COVER ASSEMBLY
  1. Install the engine under cover assembly rear with the 6 bolts.



19. INSTALL FRONT WHEEL

Torque:
112 N*m{ 1,142 kgf*cm , 83 ft.*lbf }



20. INSPECT CHECK ABS SENSOR SIGNAL

HINT:
(Click here)