DTC P1441 Stuck Open in Secondary Air Injection Vacuum Switching Valve Bank 1 |
DTC P1444 Stuck Open in Secondary Air Injection Vacuum Switching Valve Bank 2 |
DTC P2440 Secondary Air Injection System Switching Valve Stuck Open Bank1 |
| DTC No. | DTC Detection Condition | Trouble Area |
| P1441 | No. 2 air switching valve (bank 1) stuck open: The pressure sensor detects exhaust pulsation, when both of No. 2 air switching valve OFF (and air switching valve ON). (2 trip detection logic) |
|
| P1444 | No. 2 air switching valve (bank 2) stuck open: The pressure sensor detects exhaust pulsation, when both of No. 2 air switching valve OFF (and air switching valve ON). (2 trip detection logic) |
|
| P2440 | No. 2 air switching valve stuck open: The pressure sensor detects exhaust pulsation when the system is not operating (both of No. 2 air switching valve OFF, and air switching valve OFF and air pump OFF). This DTC means air switching valve and "No. 2 air switching valve bank 1 or bank 2" are stuck open. (1 trip detection logic) |
|

| Air Pump | ON |
| Air Switching Valve and No. 2 Air Switching Valve | Open |
| Pressure | 1 kPa or more |
| Pulsation detection | Exhaust gas pulsation detected |
| Air Pump | OFF |
| Air Switching Valve and No. 2 Air Switching Valve | Open |
| Pressure | Less than 5 kPa |
| Pulsation detection | Exhaust gas pulsation detected |
| Air Pump | ON |
| Air Switching Valve and No. 2 Air Switching Valve | Closed |
| Pressure | 1 kPa or more |
| Pulsation detection | Slight pulsation detected |
| Air Pump | OFF |
| Air Switching Valve and No. 2 Air Switching Valve | Closed |
| Pressure | Less than 5 kPa |
| Pulsation detection | Not detected |
| Monitor | Judgment | |||||
| C | F | A | B | D | E | DTCs that may be set |
| Pattern 1 | Pattern 1 | Pressure changed | Pressure changed | - | No pulsation detected | P2444, P1441 and P1444 |
| Pattern 1 | Pattern 1 | No pressure changed | Pressure changed | - | No pulsation detected | P2444 and "P1441 or P1444" |
| Pattern 1 | Pattern 1 | Pressure changed | No pressure changed | Pulsation detected | No pulsation detected | P2444, P1441 and P1444 |
| Pattern 1 | Pattern 1 | No pressure changed | No pressure changed | Pulsation detected | No pulsation detected | P2444, P1441 and P1444 |
| Pattern 1 | Pattern 2 | Pressure changed | Pressure changed | - | No pulsation detected | P1441 and P1444 |
| Pattern 1 | Pattern 2 | No pressure changed | Pressure changed | - | No pulsation detected | P1441 or P1444 |
| Pattern 1 | Pattern 2 | Pressure changed | No pressure changed | Pulsation detected | No pulsation detected | P1441 and P1444 |
| Pattern 1 | Pattern 2 | No pressure changed | No pressure changed | Pulsation detected | No pulsation detected | P1441 and P1444 |
| Pattern 1 | Pattern 3 | Pressure changed | Pressure changed | - | No pulsation detected | P2444 |
| Pattern 1 | Pattern 3 | No pressure changed | Pressure changed | - | No pulsation detected | P2444 and "P1442 or P1445" |
| Pattern 1 | Pattern 3 | Pressure changed | No pressure changed | No pulsation detected | No pulsation detected | P2444 and "P1442 or P1445" |
| Pattern 1 | Pattern 3 | No pressure changed | No pressure changed | No pulsation detected | No pulsation detected | P2444, P1442 and P1444 |
| Pattern 1 | Pattern 4 | Pressure changed | Pressure changed | - | No pulsation detected | Normal |
| Pattern 1 | Pattern 4 | Pressure changed | No pressure changed | Pulsation detected | No pulsation detected | Normal |
| Pattern 1 | Pattern 4 | Pressure changed | No pressure changed | No pulsation detected | No pulsation detected | P1442 or P1445 |
| Pattern 1 | Pattern 4 | No pressure changed | Pressure changed | - | No pulsation detected | P1442 or P1445 |
| Pattern 1 | Pattern 4 | No pressure changed | No pressure changed | Pulsation detected | No pulsation detected | P1442 or P1445 |
| Pattern 1 | Pattern 4 | No pressure changed | No pressure changed | No pulsation detected | No pulsation detected | P1442 and P1445 |
| Pattern 2 | - | No pressure changed | No pressure changed | - | - | P2445 |
| Pattern 3 | Pattern 3 | No pressure changed | No pressure changed | No pulsation detected | No pulsation detected | P2441, P2444, P1442 and P1445 |
| Pattern 3 | Pattern 4 | No pressure changed | No pressure changed | No pulsation detected | No pulsation detected | P2441, P1442 and P1445 |
| Pattern 4 | - | No pressure changed | No pressure changed | - | - | P2445 |
| - | - | - | - | - | Pulsation detected | P2440 and "P1441 or P1444" |
| Related DTCs | (Case 1) P1444 AIR VSV stuck open bank 1 (Case 2) P1444 AIR VSV stuck open bank 2 (Case 3) P1441, P1444 AIR VSVs stuck open (Case 4) P2440 AIR valve stuck open (Case 5) P2440 AIR valve and AIR VSVs stuck open |
| Required sensors/Components (main) | AIR valve, AIR VSV bank 1, AIR VSV bank 2 |
| Required sensors/Components (sub) | AIR pressure sensor |
| Frequency of operation | Once per driving cycle |
| Duration | Within 60 seconds |
| MIL operation | P1441, P1444: 2 driving cycles P2440: Immediate |
| Sequence operation | None |
| This monitor will run whenever these DTC are not present | P0010 - P0022 (VVT system) P0031 - P0052 (A/F sensor heater) P0100 - P0103 (MAF sensor) P0110 - P0113 (IAT sensor) P0115 - P0118 (ECT sensor) P0120 - P0223, P2135 (TP sensor) P0125 (Closed loop) P0171, P0172 (Fuel trim) P0300 - P0308 (Misfire) P0327 - P0333 (Knock sensor) P0335 (CKP sensor) P0340 - P0346 (VVT sensor) P0351 - P0358 (Ignitor) P0455, P0456 (EVAP system) P0450, P0453 (EVAP press sensor) P0500 (VSS) P2196, P2198 (A/F sensor - rationality) P2430 - P2433 (AIR pressure sensor) P2A00, P2A03 (A/F sensor - slow response) |
| Atmospheric pressure | 45 kPa (338 mmHg) or more |
| Battery voltage | 11.5 V or higher |
| Monitor Sequence 1 | |
| AIR pump | ON |
| AIR valve | ON |
| Either of following conditions is met | Condition 1 or 2 |
| 1. Both of the following conditions are met | Condition (a) and (b) |
| (a) AIR valve bank 1 (vacuum type) | ON |
| (b) AIR valve bank 2 (vacuum type) | OFF |
| 2. Both of the following conditions are met | Condition (c) and (d) |
| (c) AIR valve bank 1 (vacuum type) | OFF |
| (d) AIR valve bank 2 (vacuum type) | ON |
| Monitor Sequence 2 | |
| Idle | ON |
| AIR valve (electric type) | ON |
| AIR valve bank 1(vacuum type) | ON |
| AIR valve bank 2 (vacuum type) | ON |
| Monitor Sequence 3 | |
| Engine RPM | Less than 3,750 rpm |
| AIR pump | ON |
| AIR valve (electric type) | ON |
| AIR valve bank 1 (vacuum type) | ON |
| AIR valve bank 2 (vacuum type) | ON |
| Monitor Sequence 4 Runs when AIR pressure did not change at monitor | |
| Engine RPM | Less than 3,750 rpm |
| AIR | OFF |
| AIR pump | ON |
| AIR valve (electric type) | ON |
| Either of following conditions is met | Condition 1 or 2 |
| 1. Both of the following conditions are met | Condition (a) and (b) |
| (a) AIR valve bank 1 (vacuum type) | ON |
| (b) AIR valve bank 2 (vacuum type) | OFF |
| 2. Both of the following conditions are met | Condition (c) and (d) |
| (c) AIR valve bank 1 (vacuum type) | OFF |
| (d) AIR valve bank 2 (vacuum type) | ON |
| Monitor Sequence 4 | |
| Engine RPM | Less than 3,750 rpm |
| AIR | Not operating |
| AIR pump | OFF |
| AIR valve (electric type) | OFF |
| AIR valve bank 1 (vacuum type) | OFF |
| AIR valve bank 2 (vacuum type) | OFF |
| Monitor Sequence 5 | |
| Engine RPM | Less than 3,750 rpm |
| AIR | Not operating |
| AIR pump | OFF |
| AIR valve (electric type) | OFF |
| AIR valve bank 1 (vacuum type) | OFF |
| AIR valve bank 2 (vacuum type) | OFF |
| Monitor sequence 6 | |
| AIR status | Not operating |
| AIR pump | OFF |
| AIR valve (electric type) | ON |
| AIR valve (vacuum type) bank 1 | OFF |
| AIR valve (vacuum type) bank 2 | OFF |
| Engine RPM | Less than 3,750 rpm |
| Atmospheric pressure | 45 kPa (338 mmHg) or more |
| Battery voltage | 11.5 V or more |
| AIR pump | OFF |
| Time after engine start | 10 seconds or more |
| AIR VSV bank 1 | OFF |
| AIR VSV bank 2 | OFF |
| AIR status | OFF |
| Engine load | 0 % or more |
| Intake air amount | 40 g/sec. or more |
| IAT at engine start | -15°C (5°F) or more |
| ECT at engine start | Less than 5°C (41°F) |
| AIR valve (electric type) | ON |
| Engine RPM | Less than 3,750 rpm |
| Cumulative intake air amount | 172 g/sec. or more |
| AIR pump | OFF |
| AIR valve | OFF |
| AIR VSV bank 1 | OFF |
| AIR VSV bank 2 | OFF |
| Engine RPM | Less than 3,750 rpm |
| AIR pressure sensor malfunction (open circuit, out of range) | Not detected |
| AIR status | OFF |
| Both of the following conditions are met: | Condition 1 and 2 |
| 1. One of the following conditions is met: | Condition (a), (b) or (c) |
| (a) Both of the following conditions are met: | - |
| AIR pressure during monitor sequence 3 | 1 kPa (7.5 mmHg) or more and pulse is operated |
| AIR pressure during monitor sequence 6 | Less than 5 kPa (37.5 mmHg) and pulse is operated |
| (b) Both of the following conditions are met: | - |
| AIR pressure during monitor sequence 3 | 1 kPa (7.5 mmHg) or more and pulse is operated |
| AIR pressure during monitor sequence 6 | 5 kPa (37.5 mmHg) or more and pulse is operated |
| (c) Both of the following conditions are met: | - |
| AIR pressure during monitor sequence 3 | Less than 1 kPa (7.5 mmHg) and pulse is operated |
| AIR pressure during monitor sequence 6 | Less than 5 kPa (37.5 mmHg) and pulse is operated |
| 2. One of the following conditions is met: | Condition (d), (e) or (f) |
| (d) Both of the following conditions are met: | - |
| AIR pressure during monitor sequence 1 | Change |
| AIR pressure during monitor sequence 2 | Change |
| (e) AIR pressure during monitor sequence 1 (When AIR VSV bank 1 is open) | No change |
| (f) AIR pressure during monitor sequence 2 (When AIR VSV bank 1 is open) | No change |
| Both of the following conditions are met: | Condition 1 and 2 |
| 1. One of the following conditions is met: | Condition (a), (b) or (c) |
| (a) Both of the following conditions are met: | - |
| AIR pressure during monitor sequence 3 | 1 kPa (7.5 mmHg) or more and pulse is operated |
| AIR pressure during monitor sequence 6 | Less than 5 kPa (37.5 mmHg) and pulse is operated |
| (b) Both of the following conditions are met: | - |
| AIR pressure during monitor sequence 3 | 1 kPa (7.5 mmHg) or more and pulse is operated |
| AIR pressure during monitor sequence 6 | 5 kPa (37.5 mmHg) or more and pulse is operated |
| (c) Both of the following conditions are met: | - |
| AIR pressure during monitor sequence 3 | Less than 1 kPa (7.5 mmHg) and pulse is operated |
| AIR pressure during monitor sequence 6 | Less than 5 kPa (37.5 mmHg) and pulse is operated |
| 2. One of the following conditions is met: | Condition (d), (e) or (f) |
| (d) Both of the following conditions are met: | - |
| AIR pressure during monitor sequence 1 | Change |
| AIR pressure during monitor sequence 2 | Change |
| (e) AIR pressure during monitor sequence 1 (When AIR VSV bank 2 is open) | No change |
| (f) AIR pressure during monitor sequence 2 (When AIR VSV bank 2 is open) | No change |
| AIR pressure | Pulse is generated |
| Both of the following conditions are met: | - |
| AIR pressure during monitor sequence 3 | Less than 1 kPa (7.5 mmHg) and pulse is operated |
| AIR pressure during monitor sequence 5 | No pulse is generated |
| AIR pressure | Pulse is operated |
| MID | TID | Scaling | Description of Test Value | Minimum Test Limit | Maximum Test Limit |
| $71 | $E1 | Multiply by 0.01 (g/s) | Test value of AIR amount insufficient | Minimum test limit | Maximum test limit |
| $71 | $E2 | Multiply by 0.01 (kPa) | Test value of AIR pump stuck ON | Minimum test limit | Maximum test limit |
| $71 | $E3 | Multiply by 0.01 (kPa) | Test value of AIR pump stuck OFF | Minimum test limit | Maximum test limit |
| $71 | $E9 | Multiply by 0.01 (kPa) | Test value of AIR control valve ON | Minimum test limit | Maximum test limit |
| $71 | $E5 | Multiply by 0.01 (kPa) | Test value of AIR control valve OFF | Minimum test limit | Maximum test limit |
| $71 | $E6 | Multiply by 0.01 (kPa) | Test value of AIR pressure change for AIR valve | Minimum test limit | Maximum test limit |
| $71 | $E7 | Multiply by 0.01 (kPa) | Test value of AIR pressure change for AIR VSV bank 1 | Minimum test limit | Maximum test limit |
| $71 | $E5 | Multiply by 0.01 (kPa) | Test value of AIR pressure change for AIR VSV bank 2 | Minimum test limit | Maximum test limit |
| $71 | $E9 | Multiply by 0.01 (kPa) | Test value of AIR pressure pulsation for AIR VSV when AIR pressure is low | Minimum test limit | Maximum test limit |
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO SECONDARY AIR INJECTION SYSTEM DTCS) |
Connect the intelligent tester to the DLC3 with CAN VIM.
Turn the ignition switch ON and turn the tester ON.
Enter the following menus: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
Read DTCs.
| Display (DTC Output) | Proceed To |
| "P1441 and/or P1444" and P2440 | A |
| P1441 and/or P1444 | B |
| "P1441 and/or P1444 and/or P2440" and other DTCs | C |
|
| ||||
|
| ||||
| A | |
| 2.CHECK AIR SWITCHING VALVE (OPERATION) |
![]() |
Remove the intake manifold .
Remove the Air Switching Valve (ASV).
Blow air into port A and check that air is not discharged from port B.
![]() |
Apply battery positive voltage across the terminals.
Blow air into port A and check that air is discharged from port B.
|
| ||||
| OK | |
| 3.CHECK AIR SWITCHING VALVE (VOLTAGE) |
![]() |
Remove the intake manifold .
Disconnect the A47 ASV connector.
Turn the ignition switch ON.
Measure the voltage between terminal 1 of the air switching valve connector and body ground.
| Tester Connection | Specified Condition |
| A47-1 - Body ground | Below 1.0 V |
Reconnect the ASV connector.
|
| ||||
| OK | ||
| ||
| 4.CHECK HARNESS AND CONNECTOR (AIR INJECTION CONTROL DRIVER - AIR SWITCHING VALVE) |
![]() |
Remove the intake manifold .
Disconnect the A44 air injection driver connector.
Disconnect the A47 air switching valve connector.
Disconnect the battery positive terminal cable.
Measure the resistance between the wire harness side connectors.
| Tester Connection | Specified Condition |
| VV (A44-6) - A47-1 | Below 1 Ω |
| VV (A44-6) or A47-1 - Battery positive terminal cable | 10 kΩ or higher |
Reconnect the air injection driver connector.
Reconnect the ASV connector.
|
| ||||
| OK | |
| 5.CHECK AIR INJECTION CONTROL DRIVER (VOLTAGE) |
![]() |
Disconnect the A44 Air Injection Control Driver (AID) connector.
Turn the ignition switch ON.
Measure the voltage between terminal 3 (SIV) of the AID connector and body ground.
| Tester Connection | Specified Condition |
| SIV (A41-3) - Body ground | 10 V or more |
Reconnect the AID connector.
|
| ||||
| OK | ||
| ||
| 6.CHECK HARNESS AND CONNECTOR (AIR INJECTION CONTROL DRIVER - ECM) |
![]() |
Disconnect the air injection driver connector.
Disconnect the E9 ECM connector.
Measure the resistance between the wire harness side connectors.
| Tester Connection | Specified Condition |
| SIV (A44-3) - AIRV (E9-4) | Below 1 Ω |
| SIV (A44-3) or AIRV (E9-4) - Body ground | 10 kΩ or higher |
Reconnect the air injection driver connector.
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||
| 7.CHECK NO. 2 AIR SWITCHING VALVE (OPERATION) |
![]() |
Start the engine and warm it up.
Turn the ignition switch OFF.
Connect the intelligent tester to the DLC3 with CAN VIM.
Start the engine and push the the intelligent tester main switch ON.
Enter the following menus: DIAGNOSIS / ENHANCED OBD II / SYSTEM CHECK / AIR INJ CHECK / MANUAL / OPERATION 5 and 6.
Read values of the A/F BANK1 and BANK2 on the the intelligent tester.
| Air switching valve No. 2 operation | Air fuel ratio |
| Open | 18 or more |
| Closed | Approximately 14.5 |
| NEXT | |
| 8.CHECK VSV (FOR AIR INJECTION SYSTEM) |
![]() |
Turn the ignition switch OFF.
Disconnect the vacuum hose from the VSV for air injection system.
Connect the intelligent tester to the DLC3 with CAN VIM.
Start the engine and turn the tester ON.
Enter the following menus: DIAGNOSIS / ENHANCED OBD II / SYSTEM CHECK / AIR INJ CHECK / MANUAL / OPERATION 1.
At this time, check that no negative pressure generates at port A of the VSV.
Reconnect the vacuum hose.
|
| ||||
| OK | |
| 9.CHECK NO. 2 AIR SWITCHING VALVE (OPERATION) |
![]() |
Remove the No. 2 air switching valve.
Blow air into port B and check that air is not discharged from port C.
![]() |
Apply vacuum 30 kPa (225 mmHg) to port A, blow air into port B and check that air is discharged from port C.
|
| ||||
| OK | ||
| ||
| 10.CHECK VSV (FOR AIR INJECTION SYSTEM) |
![]() |
Disconnect the 2 vacuum hoses.
Disconnect the VSV for air injection system connector.
Blow air into port B and check that air does not flow from port A.
Apply battery positive voltage across the terminals. Then blow air into port B and check that air flows from port A.
|
| ||||
| OK | |
| 11.CHECK HARNESS AND CONNECTOR (ECM - VSV FOR AIR INJECTION SYSTEM) |
![]() |
Remove the intake manifold .
Disconnect the E5 ECM connector.
Disconnect the V10 and V11 VSV for air injection system control connector.
Measure the resistance between the VSV connector and ECM.
| Tester connection | Specified condition |
| AIV1 (E5-27) - V10-2 | Below 1 Ω |
| AIV1 (E5-26) - V11-2 | Below 1 Ω |
Measure the resistance between the VSV connector and body ground.
| Tester connection | Specified condition |
| AIV1 (E5-27) or V10-2 - Body ground | 10 kΩ or higher |
| AIV1 (E5-26) or V11-2 - Body ground | 10 kΩ or higher |
Reconnect the ECM connector.
Reconnect the VSV connector.
|
| ||||
| OK | ||
| ||