Home › SUSPENSION & AXLE › SUSPENSION CONTROL › AIR SUSPENSION SYSTEM

DTC    C1742/42    Height Control Compressor Circuit

for Preparation Click here


DESCRIPTION

When the "UP" side of the height control switch is pressed, a signal is sent from terminal RC of the suspension control ECU to switch the AIR SUS relay ON. As a result, the relay contacts close and the compressor motor turns on, producing compressed air.
The suspension control ECU detects the amount of current flow to the compressor motor by means of the differences in potential at terminals RM+ and RM- of the suspension control ECU. In this way, the suspension control ECU monitors the compressor circuit for abnormalities.

DTC No.
DTC Detecting Condition
Trouble Area
C1742/42
With the AIR SUS relay activated, a lock, open or short signal of the height control compressor motor is detected for 4 sec. or more.
  1. Height control compressor assembly
  2. Height control compressor circuit
  3. Suspension control ECU

HINT:
Once the ECU stores DTC C1742/42 in the memory, the vehicle height control is not carried out until the normal signal is input to the ECU from the compressor motor. However, the control automatically resumes approx. 70 min. after the ignition switch is turned ON.


WIRING DIAGRAM


F050632E01


INSPECTION PROCEDURE

1.CHECK DTC
  1. Check if the other DTC is recorded (Click here).

    Result:
    Result
    Proceed to
    Other DTC is not output.
    A
    Other DTC is output.
    B



B
REPAIR CIRCUIT INDICATED BY OUTPUT DTC
A


2.INSPECT HEIGHT CONTROL COMPRESSOR ASSEMBLY


    F043249E01
  1. Disconnect the height control compressor assembly connector.

  1. Apply battery voltage between terminal 1 and 2 of the height control compressor assembly.

    Standard:
    Compressor motor operates.

    NOTICE:
    1. Do not operate the height control compressor assembly 90 sec. or more.
    2. Since short and lock inside the height control compressor assembly causes enormous current to flow, stop the operation immediately when it dose not rotate.



NG
REPLACE HEIGHT CONTROL COMPRESSOR ASSEMBLY
OK


3.CHECK HARNESS AND CONNECTOR (HEIGHT CONTROL COMPRESSOR ASSEMBLY - SUSPENSION CONTROL ECU)
  1. Check for open and short circuit in the harness and the connector between the height control compressor assembly and the suspension control ECU (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (HEIGHT CONTROL COMPRESSOR ASSEMBLY - AIR SUS RELAY)
  1. Check for open and short circuit in the harness and the connector between the height control compressor assembly and the AIR SUS relay (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT HEIGHT CONTROL SOLENOID VALVE OR EXHAUST SOLENOID VALVE
  1. When using intelligent tester:

    1. Connect the intelligent tester to DLC3.

    2. Turn the ignition switch ON, and push the intelligent tester main switch ON.

    3. Select the item "LEVEL SOL REAR", "GATE SOL REAR", "LOW PRS TNK SOL", "EXHAUST SOL", in the ACTIVE TEST, and operate it with the intelligent tester.

    4. Check whether the solenoid makes sound.

    5. Check whether the height control solenoid valve has a continuity (will vibrate).

      OK:
      The solenoid makes sound, the height control solenoid valve has a continuity (will vibrate).



    F044510E01
  1. When not using intelligent tester:

    1. Disconnect the valve connector.

    2. Check the operating sound of the valves when battery positive voltage is applied to the terminals as shown below.
      Solenoid valve
      Battery positive
      Battery negative
      Gate solenoid valve
      1
      2
      Leveling solenoid valve
      3
      2
      Exhaust solenoid valve
      1
      2
      Tank solenoid valve
      2
      1

      OK:
      It should make an operating sound (click).

      HINT:
      1. When a malfunction is found in the gate solenoid valve, the leveling valve or the tank solenoid valve, replace the height control reservoir assembly.
      2. When a malfunction is found in the exhaust solenoid valve, replace the height control compressor assembly.



NG
REPLACE HEIGHT CONTROL RESERVOIR ASSEMBLY

NG
REPLACE HEIGHT CONTROL COMPRESSOR ASSEMBLY
OK


6.CHECK AIR TUBE CLOGGED
  1. Check visually for clog, damage or breakage on the air tube (Click here).



NG
REPAIR OR REPLACE AIR TUBE
OK

REPLACE SUSPENSION CONTROL ECU