Home › DRIVE LINE ยท VF4AM TRANSFER › TRANSFER ASSEMBLY

TRANSFER ASSEMBLY > REMOVAL

for Preparation Click here



1. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Remove the 4 bolts, then remove the No. 1 engine under cover sub-assembly.



2. REMOVE REAR ENGINE UNDER COVER ASSEMBLY


3. DISCONNECT OXYGEN SENSOR

HINT:
(Click here)



4. REMOVE EXHAUST PIPE ASSEMBLY

HINT:
(Click here)



5. REMOVE FRONT PROPELLER SHAFT ASSEMBLY


    C098708E05
  1. Place matchmarks on the propeller shaft flange and differential.

  1. Remove the 4 nuts, 4 bolts, 4 washers and front propeller shaft assembly.



    C098709E04
  1. Place matchmarks on the propeller shaft flange and transfer flange.

  1. Remove the 4 nuts, 4 washers and front propeller shaft assembly.



6. REMOVE PROPELLER SHAFT ASSEMBLY


    C098711E01
  1. Place matchmarks on the propeller shaft flange and differential flange.

  1. Remove the 4 nuts and 4 washers.



    C098710E02
  1. Remove the propeller shaft.

  1. Insert SST in the transmission to prevent oil leakage.

    SST
    09325-40010  



7. DRAIN AUTOMATIC TRANSMISSION FLUID


    G036650E01
  1. Remove the drain plug and gasket, and drain the ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



8. DRAIN TRANSFER OIL


9. REMOVE FRONT SUSPENSION MEMBER BRACKET


    F042934
  1. Remove the 4 bolts and front suspension member bracket.



10. REMOVE FRONT SUSPENSION MEMBER BRACKET LH
  1. Remove the 4 bolts and front suspension member bracket LH.



11. REMOVE TRANSMISSION OIL FILTER TUBE SUB-ASSEMBLY


12. DISCONNECT NO. 1 OIL COOLER OUTLET TUBE


  1. Remove the 2 bolts and 2 clamps.


    G038661

  1. Using SST, disconnect the No. 1 oil cooler outlet tube.

    SST
    09023-12701  



13. REMOVE NO. 1 OIL COOLER INLET TUBE


    Z035557E01
  1. Using SST, disconnect the No. 1 oil cooler inlet tube.

    SST
    09023-12701  



14. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    D028154E01
  1. Remove the nut and clip and disconnect the transmission control cable assembly from the No. 1 transmission control cable bracket.



15. REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET


    G036547E01
  1. Remove the 2 bolts and No.1 transmission control cable bracket from the transmission assembly.



16. REMOVE TRANSFER CASE LOWER PROTECTOR


    F043499
  1. Remove the 4 bolts and transfer case lower protector.



17. SUPPORT AUTOMATIC TRANSMISSION WITH TRANSFER


    D028162
  1. Support the transmission with a transmission jack.



18. REMOVE NO. 3 CROSSMEMBER SUB-ASSEMBLY


    F042938E02
  1. Remove the 4 nuts, 8 bolts and No. 3 frame crossmember sub-assembly.



19. DISCONNECT CONNECTOR


20. DISCONNECT WIRE HARNESS


21. REMOVE STARTER ASSEMBLY

HINT:
(Click here for Standard or Click here for Cold Area)



22. REMOVE MANIFOLD STAY
  1. Remove the 3 bolts and manifold stay.



23. REMOVE NO. 2 MANIFOLD STAY
  1. Remove the 3 bolts and No. 2 manifold stay.



24. SEPARATE FRONT DIFFERENTIAL ASSEMBLY


25. REMOVE AUTOMATIC TRANSMISSION WITH TRANSFER


    F044115
  1. Remove the torque converter housing side cover from the engine.

  1. Turn the crankshaft to gain access to each bolt.

  1. Hold the crankshaft pulley nut with a wrench and remove the 6 bolts.



    D028727E01
  1. Remove the 9 bolts.

  1. Separate and remove the automatic transmission assembly.



26. REMOVE TRANSFER ASSEMBLY


    F043500
  1. Remove the 8 bolts and 2 clamps.

  1. Remove the transfer from the automatic transmission.