Home › SUSPENSION & AXLE › SUSPENSION › FRONT SHOCK ABSORBER

FRONT SHOCK ABSORBER > INSTALLATION

for Preparation Click here



1. INSTALL FRONT SHOCK ABSORBER BUSH


    C099164E01
  1. Using SST and a press, install a new absorber bush.

    SST
    09710-22021   (09710-01071, 09710-01081)



2. INSTALL FRONT COIL SPRING LH


    C099165E01
  1. Using SST, compress the front coil spring LH.

    SST
    09727-30021   (09727-00010, 09727-00031)
    09727-00060  

    NOTICE:
    Do not use an impact wrench. It will damage the SST.

  1. Install the front coil spring LH to the shock absorber assembly front LH.

    HINT:
    Fit the lower end of the front coil spring LH into the gap of the spring lower seat.



3. INSTALL FRONT SHOCK ABSORBER CUSHION RETAINER


4. INSTALL FRONT SUSPENSION SUPPORT SUB-ASSEMBLY LH


5. INSTALL FRONT SHOCK ABSORBER CUSHION NO. 1


6. INSTALL FRONT SHOCK ABSORBER CUSHION RETAINER


7. INSTALL FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT


    C099166E01
  1. Align the suspension support sub-assembly and the absorber bush as shown in the illustration.

  1. Tighten the new lock nut.

    Torque:
    25 N*m{ 260 kgf*cm , 18 ft.*lbf }

    NOTICE:
    Do not use an impact wrench. It will damage the shock absorber rod.

  1. Release the coil spring while checking the position of the suspension support.



8. TEMPORARILY TIGHTEN FRONT SHOCK ABSORBER WITH COIL SPRING (w/o REAS)


    G021681E01
  1. Install the coil spring on the body as the lower end of the coil spring faces rear side of the vehicle.



    C099160
  1. Install the 3 nuts on the upper side of the front shock absorber with coil spring.

    Torque:
    64 N*m{ 650 kgf*cm , 47 ft.*lbf }



    C099159
  1. Temporarily tighten the bolt, the nut and the washer as shown in the illustration.



9. TEMPORARILY TIGHTEN FRONT SHOCK ABSORBER WITH COIL SPRING (w/ REAS)


    G021681E01
  1. Install the coil spring on the body as the lower end of the coil spring faces rear side of the vehicle.



    C099160
  1. Install the 3 nuts on the upper side of the front shock absorber with coil spring.

    Torque:
    64 N*m{ 650 kgf*cm , 47 ft.*lbf }



    C099159
  1. Temporarily tighten the bolt, the nut and the washer as shown in the illustration.



    G020405
  1. Install the bolt.

    Torque:
    29 N*m{ 300 kgf*cm , 21 ft.*lbf }

    NOTICE:
    Be sure to fit the detents attached to the bracket into a hole on the frame side.



    G020406E01
  1. As shown in the illustration, tighten the nut of clearance to standard value.

    Clearance:
    1 mm (0.04 in.)

    Torque:
    Reference torque:
    25 N*m{ 260 kgf*cm , 18 ft.*lbf }



10. INSTALL STABILIZER BAR FRONT


11. INSTALL FRONT STABILIZER BRACKET NO. 2 LH


    G020162
  1. Install the front stabilizer bracket No.2 LH with the 2 bolts.

    Torque:
    40 N*m{ 410 kgf*cm , 30 ft.*lbf }



12. INSTALL FRONT STABILIZER BRACKET NO. 1 RH

HINT:
Install the RH side by following the same procedures with the LH side.



13. INSTALL FRONT STABILIZER LINK ASSEMBLY LH


    C099158
  1. Connect the stabilizer link with the nut to the steering knuckle.

    Torque:
    70 N*m{ 710 kgf*cm , 52 ft.*lbf }

    HINT:
    If the ball joint turns together with the nut, use a hexagon (6 mm) wrench to hold the stud.



14. INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Install the RH side by the same procedures with the LH side.



15. INSTALL FRONT DISC WHEEL

Torque:
112 N*m{ 1,140 kgf*cm , 83 ft.*lbf }



16. STABILIZE SUSPENSION
  1. Jack down the vehicle.

  1. Bounce the vehicle up and down several times to stabilize the suspension.



17. FULLY TIGHTEN FRONT SHOCK ABSORBER WITH COIL SPRING


    C099159
  1. Fully tighten the nut.

    Torque:
    135 N*m{ 1,380 kgf*cm , 100 ft.*lbf }



18. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

HINT:
(Click here)