DTC P0136 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2) |
DTC P0137 Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2) |
DTC P0138 Oxygen Sensor Circuit High Voltage (Bank 1 Sensor 2) |
DTC P0156 Oxygen Sensor Circuit Malfunction (Bank 2 Sensor 2) |
DTC P0157 Oxygen Sensor Circuit Low Voltage (Bank 2 Sensor 2) |
DTC P0158 Oxygen Sensor Circuit High Voltage (Bank 2 Sensor 2) |

| DTC No. | DTC Detection Conditions | Trouble Areas |
| P0136 P0156 |
|
|
| P0137 P0157 |
|
|
| P0138 P0158 |
|
|


![]() |
| Related DTCs | P0136: Heated oxygen sensor output voltage (Output voltage) (bank 1) P0136: Heated oxygen sensor impedance (Low) (bank 1) P0137: Heated oxygen sensor output voltage (Low voltage) (bank 1) P0137: Heated oxygen sensor impedance (High) (bank 1) P0138: Heated oxygen sensor output voltage (High voltage) (bank 1) P0138: Heated oxygen sensor output voltage (Extremely high) (bank 1) P0156: Heated oxygen sensor output voltage (Output voltage) (bank 2) P0156: Heated oxygen sensor impedance (Low) (bank 2) P0157: Heated oxygen sensor output voltage (Low voltage) (bank 2) P0157: Heated oxygen sensor impedance (High) (bank 2) P0158: Heated oxygen sensor output voltage (High voltage) (bank 2) P0158: Heated oxygen sensor impedance (Extremely high) (bank 2) |
| Required Sensors / Components (Main) | Heated oxygen sensor |
| Required Sensors / Components (Related) | Crankshaft position sensor, Engine coolant temperature sensor, Mass air flow meter, Throttle position sensor, Vehicle speed sensor |
| Frequency of Operation | Once per driving cycle: Active air-fuel ratio control detection Continuous: Others |
| Duration | 20 seconds.: Heated oxygen sensor output (Output voltage, High voltage, Low voltage) 30 seconds.: Heated oxygen sensor impedance (Low) 90 seconds.: Heated oxygen sensor impedance (High) 10 seconds.: Heated oxygen sensor impedance (Extremely high) |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| The monitor will run whenever these DTCs are not present | P0031, P0032, P0051, P0052 (A/F Sensor Heater Sensor 1), P0100, P0101, P0102, P0103 (MAF Sensor), P0110, P0112, P0113 (IAT Sensor), P0115, P0116, P0117, P0118 (ECT Sensor), P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (TP Sensor), P0125 (Insufficient ECT for Closed Loop), P0137, P0138 (O2 Sensor 1), P0171,P0172 (Fuel System), P0300, P0301, P0302, P0303, P0304, P0305, P0306 (Misfire), P0335 (CKP Sensor), P0340, P0342, P0343, P0345 (VVT Sensor 1,2), P0500 (VSS), P2196, P2198 (A/F Sensor (Rationality)), P2A00, P2A03 (A/F Sensor (Slow Response)) |
| Active air-fuel ratio control | Performing |
| Active air-fuel ratio control begins when all of following conditions met: | - |
| Battery voltage | 11 V or more |
| Engine coolant temperature | 75°C (167°F) or more |
| Idle | OFF |
| Engine RPM | Less than 3,200 rpm |
| A/F sensor status | Activated |
| Fuel-cut | OFF |
| Engine load | 10 to 70% |
| Shift position | 4th or more |
| Battery voltage | 11 V or more |
| Estimated HO2S temperature | Less than 700°C (1,292°F) |
| ECM monitor | Completed |
| DTC P0606 | Not set |
| Battery voltage | 11 V or more |
| Estimated HO2S temperature | 450°C (842°F) or more |
| DTC P0606 | Not present |
| Battery voltage | 11 V or more |
| Time after engine start | 2 seconds or more |
| Either of the following conditions is met: | Condition 1 or 2 |
| 1. All of the following conditions (a), (b) and (c) are met | - |
| (a) Commanded air-fuel ratio | 14.3 or less |
| (b) Rear HO2 sensor voltage | 0.21 to 0.59 V |
| (c) OSC (Oxygen Storage Capacity of Catalyst) | 2.5 g or more |
| 2. All of the following conditions (d), (e) and (f) are met. | - |
| (d) Commanded air-fuel ratio | 14.9 or more |
| (e) Rear HO2 sensor voltage | 0.21 to 0.59 V |
| (f) OSC | 2.5 g or more |
| All of the following conditions (a), (b) and (c) are met. | - |
| (a) Commanded air-fuel ratio | 14.3 or less |
| (b) Rear HO2 sensor voltage | Less than 0.21 V |
| (c) OSC (Oxygen Storage Capacity of Catalyst) | 2.5 g or more |
| All of the following conditions (a), (b) and (c) are met. | - |
| (a) Commanded air-fuel ratio | 14.9 or more |
| (b) Rear HO2 sensor voltage | More than 0.59 V |
| (c) OSC (Oxygen Storage Capacity of Catalyst) | 2.5 g or more |
| Duration of following condition | 30 seconds or more |
| Rear heated oxygen sensor impedance | Less than 5 Ω |
| Duration of following condition | 90 seconds or more |
| Rear heated oxygen sensor impedance | 15 kΩ or more |
| Duration of following condition | 10 seconds or more |
| Rear heated oxygen sensor voltage | 1.2 V or more |
| Heated oxygen sensor voltage | Varies between 0.1 and 0.9 V |
| Test ID/Comp ID | Description of Test Data | Conversion Factor | Unit |
| $07 | The minimum sensor voltage while the malfunction is being monitored | N/A | V |
| $08 | The maximum sensor voltage while the malfunction is being monitored | N/A | V |
| Test ID/Comp ID | Description of Test Data | Conversion Factor | Unit |
| $81 | Percentage of monitoring time where heated oxygen sensor voltage is less than 0.05 V | Multiply 0.3906 | % |
| $84 | Percentage of monitoring time where heated oxygen sensor voltage is 0.70 V or more | Multiply 0.3906 | % |
| $85 | Maximum Rich (0.45 V or more) time | Multiply 0.2621 | second |


![]() |
| Tester Display (Sensor) | Injection Volumes | Status | Voltages |
| AFS B1S1 or AFS B2S1 (A/F) | +25% | Rich | Less than 3.0 |
| AFS B1S1 or AFS B2S1 (A/F) | -12.5% | Lean | More than 3.35 |
| O2S B1S2 or O2S B2S2 (HO2) | +25% | Rich | More than 0.55 |
| O2S B1S2 or O2S B2S2 (HO2) | -12.5% | Lean | Less than 0.4 |
| Case | A/F Sensor (Sensor 1) Output Voltage | HO2 Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area | ||
| 1 | Injection Volume +25% -12.5% | ![]() | Injection Volume +25% -12.5% | ![]() | - |
| Output Voltage More than 3.35 V Less than 3.0 V | ![]() | Output Voltage More than 0.55 V Less than 0.4 V | ![]() | ||
| 2 | Injection Volume +25% -12.5% | ![]() | Injection Volume +25% -12.5% | ![]() |
|
| Output Voltage Almost no reaction | ![]() | Output Voltage More than 0.55 V Less than 0.4 V | ![]() | ||
| 3 | Injection Volume +25% -12.5% | ![]() | Injection Volume +25% -12.5% | ![]() |
|
| Output Voltage More than 3.35 V Less than 3.0 V | ![]() | Output Voltage Almost no reaction | ![]() | ||
| 4 | Injection volume +25 % -12.5% | ![]() | Injection Volume +25% -12.5% | ![]() |
|
| Output Voltage Almost no reaction | ![]() | Output Voltage Almost no reaction | ![]() | ||
| 1.READ DTC OUTPUT |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on and turn the tester on.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
Read DTCs.
| Display (DTC Output) | Proceed to |
| P0138 or P0158 | A |
| P0137 or P0157 | B |
| P0136 or P0156 | C |
|
| ||||
|
| ||||
| A | |
| 2.READ VALUE OF INTELLIGENT TESTER (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on and turn the tester on.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / PRIMARY / O2S B1S2 or O2S B2S2.
Allow the engine to idle.
Read the Heated Oxygen (HO2) sensor output voltage while idling.
| HO2 Sensor Output Voltages | Proceed to |
| More than 1.2 V | A |
| Less than 1.0 V | B |
|
| ||||
| A | |
| 3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT) |
![]() |
Turn the ignition switch off and wait for 5 minutes.
Disconnect the E4 or E5 ECM connector.
Measure the resistance.
| Tester Connections | Specified Conditions |
| HT1B (E4-1) - OX1B (E4-18) | 10 kΩ or higher |
| HT2B (E5-5) - OX2B (E5-33) | 10 kΩ or higher |
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||
| 4.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT) |
![]() |
Disconnect the H6 or H8 Heated Oxygen (HO2) sensor connector.
Measure the resistance between the terminals of the HO2 sensor connector.
| Tester Connections | Specified Conditions |
| +B (2) - E1 (4) | 10 kΩ or higher |
| +B (2) - OX (3) | 10 kΩ or higher |
| Tester Connections | Specified Conditions |
| +B (2) - E1 (4) | 10 kΩ or higher |
| +B (2) - OX (3) | 10 kΩ or higher |
Reconnect the HO2 sensor connector.
|
| ||||
| OK | ||
| ||
| 5.PERFORM CONFIRMATION DRIVING PATTERN |
Perform confirmation driving pattern (Click here).
| NEXT | |
| 6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0138 OR P0158) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on and turn the tester on.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
Read DTCs.
| Display (DTC Output) | Proceed to |
| P0138 or P0158 | A |
| No output | B |
|
| ||||
| A | ||
| ||
| 7.READ VALUE OF INTELLIGENT TESTER (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on and turn the tester on.
Start the engine.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DATA LIST / ALL / O2S B1S2 or O2S B1S2.
After warming up the engine, run the engine at an engine speed of 2,500 rpm for 3 minutes.
Read the output voltage of the HO2 sensor when the engine rpm is suddenly increased.
|
| ||||
| OK | |
| 8.PERFORM CONFIRMATION DRIVING PATTERN |
Perform confirmation driving pattern (Click here).
| NEXT | |
| 9.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136 OR P0156) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on and turn the tester on.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
Read DTCs.
| Display (DTC Output) | Proceed to |
| P0136 or P0156 | A |
| No output | B |
|
| ||||
| A | |
| 10.REPLACE HEATED OXYGEN SENSOR |
Replace the heated oxygen sensor .
| NEXT | |
| 11.PERFORM CONFIRMATION DRIVING PATTERN |
Perform confirmation driving pattern (Click here).
| NEXT | |
| 12.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136 OR P0156) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on and turn the tester on.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
Read DTCs.
| Display (DTC Output) | Proceed to |
| P0136 or P0156 | A |
| No output | B |
|
| ||||
| A | |
| 13.PERFORM ACTIVE TEST BY INTELLIGENT TESTER (INJECTION VOLUME) |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Warm up the engine.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST / INJ VOL.
Change the fuel injection volume using the tester, monitoring the voltage output of Air-Fuel Ratio (A/F) and HO2 sensors displayed on the tester.
| Tester Display (Sensor) | Voltage Variations | Proceed to |
| AFS B1S1 (A/F) AFS B2S1 (A/F) | Alternates between more and less than 3.3 V | OK |
| AFS B1S1 (A/F) AFS B2S1 (A/F) | Remains at more than 3.3 V | NG |
| AFS B1S1 (A/F) AFS B2S1 (A/F) | Remains at less than 3.3 V | NG |

|
| ||||
| OK | ||
| ||
| 14.CHECK FOR EXHAUST GAS LEAKAGE |
|
| ||||
| OK | |
| 15.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the H6 or H8 Heated Oxygen (HO2) sensor connector.
Measure the resistance between the terminals of the HO2 sensor connector.
| Tester Connections | Specified Conditions |
| HT (1) - +B (2) | 11 to 16 Ω at 20°C (68°F) |
| HT (1) - E1 (4) | 10 kΩ or higher |
| Tester Connections | Specified Conditions |
| HT (1) - +B (2) | 11 to 16 Ω at 20°C (68°F) |
| HT (1) - E1 (4) | 10 kΩ or higher |
Reconnect the HO2 sensor connector.
|
| ||||
| OK | |
| 16.INSPECT EFI RELAY |
![]() |
Remove the EFI relay from the engine room R/B.
Measure the EFI relay resistance.
| Tester Connections | Specified Conditions |
| 3 - 5 | 10 kΩ or higher |
| 3 - 5 | Below 1 Ω (when battery voltage applied to terminals 1 and 2) |
Reinstall the EFI relay.
|
| ||||
| OK | |
| 17.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM) |
![]() |
Disconnect the H6 or H8 HO2 sensor connector.
Turn the ignition switch on.
Measure the voltage between the +B terminal of the HO2 sensor connector and body ground.
| Tester Connections | Specified Conditions |
| +B (H6-2) - Body ground | 9 V to 14 V |
| +B (H8-2) - Body ground | 9 V to 14 V |
Turn the ignition switch off.
Disconnect the E4 and E5 ECM connectors.
Measure the resistance.
| Tester Connections | Specified Conditions |
| HT (H6-1) - HT1B (E4-1) | Below 1 Ω |
| OX (H6-3) - OX1B (E4-18) | Below 1 Ω |
| E1 (H6-4) - E2 (E4-28) | Below 1 Ω |
| HT (H8-1) - HT2B (E5-5) | Below 1 Ω |
| OX (H8-3) - OX2B (E5-33) | Below 1 Ω |
| E1 (H8-4) - E2 (E4-28) | Below 1 Ω |
| Tester Connections | Specified Conditions |
| HT (H6-1) or HT1B (E4-1) - Body ground | 10 kΩ or higher |
| OX (H6-3) or OX1B (E4-18) - Body ground | 10 kΩ or higher |
| E1 (H6-4) or E2 (E4-28) - Body ground | 10 kΩ or higher |
| HT (H8-1) or HT2B (E5-5) - Body ground | 10 kΩ or higher |
| OX (H8-3) or OX2B (E5-33) - Body ground | 10 kΩ or higher |
| E1 (H8-4) or E2 (E4-28) - Body ground | 10 kΩ or higher |
Reconnect the HO2 sensor connector.
Reconnect the ECM connectors.

|
| ||||
| OK | ||
| ||