DTC P0420 Catalyst System Efficiency Below Threshold (Bank 1) |
DTC P0430 Catalyst System Efficiency Below Threshold (Bank 2) |
| DTC No. | DTC Detection Conditions | Trouble Areas |
| P0420 | OSC value smaller than standard value under active air-fuel ratio control (2 trip detection logic) |
|
| P0430 | OSC value smaller than standard value under active air-fuel ratio control (2 trip detection logic) |
|
| Related DTCs | P0420: Catalyst (Bank 1) Deterioration P0430: Catalyst (Bank 2) Deterioration |
| Required Sensors / Components (Main) | Catalyst |
| Required Sensors / Components (Related) | A/F sensor, Rear HO2S, IAT sensor, MAF meter, Crankshaft position sensor, ECT sensor |
| Frequency of Operation | Once per driving cycle |
| Duration | 30 seconds |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| The monitor will run whenever these DTCs are not present | P0011, P0012 (VVT System1-Advance, Retard), P0021, P0022 (VVT System2-Adavance, Retard), P0031, P0032, P0051, P0052 (A/F Sensor Heater Sensor 1), P0037, P0038, P0057, P0058 (O2 Sensor heater Sensor 2), P0100, P0101, P0102, P0103 (MAF Sensor), P0115, P0116, P0117, P0118 (ECT Sensor), P0120, P0121, P0122, P0123, P0220, P0222, P0223 , P2135 (TP Sensor), P0125 (Insufficient ECT for Closed Loop), P0136, P0156 (O2 Sensor 2), P0171,P0172 (Fuel System), P0300, P0301, P0302, P0303, P0304, P0305, P0306 (Misfire), P0335 (CKP Sensor), P0340, P0342, P0343 (CMP Sensor), P0351, P0352, P0353, P0354, P0355, P0356 (Ignitor), P0500 (VSS), P2196, P2198 (A/F Sensor (Rationality)), P2A00, P2A03 (A/F Sensor (Slow Response)) |
| Battery voltage | 11 V or more |
| IAT | -10°C (14°F) or more |
| ECT | 75°C (167°F) or more |
| Atmospheric pressure coefficient | 0.75 or more |
| Idle | OFF |
| Engine RPM | Less than 3,200 rpm |
| A/F sensor | Activated |
| Fuel system status | Closed loop |
| Engine load | 10 to 70% |
| All of the following conditions are met | Condition 1, 2 and 3 |
| 1. MAF | 15 to 70 g/sec. |
| 2. Front catalyst temperature (estimated) | 620 to 840°C (1,148 to 1,544°F) |
| 3. Rear catalyst temperature (estimated) | 100 to 900°C (212 to 1,652°F) |
| Rear HO2S | Completed |
| Shift position | 4th or more |
| Oxygen Storage Capacity (OSC) of catalyst | Less than 0.04 g |
| TLT | CID | Unit Conversion | Description of Test Data | Description of Test Limit |
| 1 | $01 | Multiply by 0.0078 (no dimension) | Oxygen storage capacity (bank 1): Calculated by HO2S sensor 2 output | Malfunction criteria for catalyst deterioration |
| 1 | $02 | Multiply by 0.0078 (no dimension) | Oxygen storage capacity (bank 2): Calculated by HO2S sensor 2 output | Malfunction criteria for catalyst deterioration |


| A/F CONTROL |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Warm up the engine at an engine speed of 2,500 rpm for approximately 90 seconds.
On the tester, select the following menu items: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST / A/F CONTROL.
Perform the A/F CONTROL operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).
Monitor the voltage outputs of the A/F and HO2 sensors (AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2) displayed on the tester.
| Tester Display (Sensor) | Injection Volumes | Status | Voltages |
| AFS B1S1 or AFS B2S1 (A/F) | +25% | Rich | Less than 3.0 |
| AFS B1S1 or AFS B2S1 (A/F) | -12.5% | Lean | More than 3.35 |
| O2S B1S2 or O2S B2S2 (HO2) | +25% | Rich | More than 0.55 |
| O2S B1S2 or O2S B2S2 (HO2) | -12.5% | Lean | Less than 0.4 |
| Case | A/F Sensor (Sensor 1) Output Voltage | HO2 Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area | ||
| 1 | Injection Volume +25% -12.5% | ![]() | Injection Volume +25% -12.5% | ![]() | - |
| Output Voltage More than 3.35 V Less than 3.0 V | ![]() | Output Voltage More than 0.55 V Less than 0.4 V | ![]() | ||
| 2 | Injection Volume +25% -12.5% | ![]() | Injection Volume +25% -12.5% | ![]() |
|
| Output Voltage Almost no reaction | ![]() | Output Voltage More than 0.55 V Less than 0.4 V | ![]() | ||
| 3 | Injection Volume +25% -12.5% | ![]() | Injection Volume +25% -12.5% | ![]() |
|
| Output Voltage More than 3.35 V Less than 3.0 V | ![]() | Output Voltage Almost no reaction | ![]() | ||
| 4 | Injection volume +25% -12.5% | ![]() | Injection Volume +25% -12.5% | ![]() |
|
| Output Voltage Almost no reaction | ![]() | Output Voltage Almost no reaction | ![]() | ||
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420 AND/OR P0430) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on and turn the tester on.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
Read DTCs.
| Display (DTC Output) | Proceed to |
| P0420 and/or P0430 | A |
| P0420 and/or P0430 and other DTCs | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST BY INTELLIGENT TESTER (A/F CONTROL) |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Warm up the engine at an engine speed of 2,500 rpm for approximately 90 seconds.
Select the following menu items on the tester: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST / A/F CONTROL.
Perform the A/F CONTROL operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).
Monitor the voltage outputs of the A/F and HO2 sensors (AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2) displayed on the tester.
| Tester Display (Sensor) | Injection Volumes | Status | Voltages |
| AFS B1S1 or AFS B2S1 (A/F) | +25% | Rich | Less than 3.0 |
| AFS B1S1 or AFS B2S1 (A/F) | -12.5% | Lean | More than 3.35 |
| O2S B1S2 or O2S B2S2 (HO2) | +25% | Rich | More than 0.55 |
| O2S B1S2 or O2S B2S2 (HO2) | -12.5% | Lean | Less than 0.4 |
| Status AFS B1S1 or AFS B2S1 | Status O2S B1S2 or O2S B2S2 | A/F Condition and A/F and HO2 Sensor Conditions | Misfires | Suspected Trouble Areas | Proceed to |
| Lean/Rich | Lean/Rich | Normal | - |
| A |
| Lean | Lean/Rich | A/F sensor malfunction | - | A/F sensor | B |
| Rich | Lean/Rich | A/F sensor malfunction | - | A/F sensor | B |
| Lean/Rich | Lean | HO2 sensor malfunction | - |
| C |
| Lean/Rich | Rich | HO2 sensor malfunction | - |
| C |
| Lean | Lean | Actual air-fuel ratio lean | May occur |
| A |
| Rich | Rich | Actual air-fuel ratio rich | - |
| A |
|
| ||||
|
| ||||
| A | |
| 3.CHECK FOR EXHAUST GAS LEAKAGE |
|
| ||||
| OK | ||
| ||