DTC P2195 Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1) |
DTC P2196 Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1) |
DTC P2197 Oxygen (A/F) Sensor Signal Stuck Lean (Bank 2 Sensor 1) |
DTC P2198 Oxygen (A/F) Sensor Signal Stuck Rich (Bank 2 Sensor 1) |

| DTC No. | DTC Detection Conditions | Trouble Areas |
| P2195 P2197 | Conditions (a) and (b) continue for 2 seconds or more (2 trip detection logic): (a) Air-Fuel Ratio (A/F) sensor voltage is more than 3.8 V (b) Heated Oxygen (HO2) sensor voltage is 0.15 V or more |
|
| P2195 P2197 | While fuel-cut operation is performed (during vehicle deceleration), air-furl ratio (A/F) sensor current is 3.6 mA or more for 3 seconds |
|
| P2196 P2198 | Conditions (a) and (b) continue for 2 seconds or more (2 trip detection logic): (a) A/F sensor voltage is less than 2.8 V (b) HO2 sensor voltage is less than 0.6 V |
|
| P2196 P2198 | While fuel-cut operation is performed (during vehicle deceleration), air-furl ratio (A/F) sensor current less than 1.4 mA for 3 seconds (2 trip detection logic) |
|

| Related DTCs | P2195: A/F sensor (Bank 1) signal stuck lean P2196: A/F sensor (Bank 1) signal stuck rich P2197: A/F sensor (Bank 2) signal stuck lean P2198: A/F sensor (Bank 2) signal stuck rich |
| Required Sensors / Components (Main) | A/F sensor |
| Required Sensors / Components (Related) | - |
| Frequency of Operation | Continuous |
| Duration | 10 seconds: A/F sensor signal stuck lean/rich 3 seconds: A/F sensor current (high/low side) |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| The monitor will run whenever these DTCs are not present | P0031, P0032, P0051, P0052 (A/F Sensor heater Sensor 1), P0037, P0038, P0057, P0058 (O2 Sensor heater Sensor 2), P0100, P0101, P0102, P0103 (MAF Sensor), P0110, P0112, P0113 (IAT Sensor), P0115, P0116, P0117, P0118 (ECT Sensor), P0120, P0121, P0122, P0123, P0220, P0222, P0223 (TP Sensor), P0125 (Insufficient ECT for Closed Loop), P0136, P0156 (O2 Sensor 2), P0171, P0172 (Fuel System), P0300, P0301, P0302, P0303, P0304, P0305, P0306 (Misfire), P0335 (CKP Sensor), P0340 (CMP Sensor), P0450, P0451, P0452, P0453, P0455, P0456 (EVAP System), P0500 (VSS) |
| Duration while all of the following conditions met | 2 seconds or more |
| Rear HO2S voltage | 0.15 V or more |
| Time after engine start | 30 seconds or more |
| A/F sensor status | Activated |
| Fuel system status | Closed-loop |
| Engine | Running |
| Duration while all of the following conditions met | 2 seconds or more |
| Rear HO2S voltage | Less than 0.6 V |
| Time after engine start | 30 seconds or more |
| A/F sensor status | Activated |
| Fuel system status | Closed-loop |
| Engine | Running |
| Battery voltage | 11 V or more |
| ECT | 75°C (167°F) or more |
| Atmospheric pressure | 570 mmHg or higher |
| A/F sensor status | Activated |
| Continuous time of fuel-cut | 3 to 10 seconds. |
| Battery voltage | 11 V or more |
| ECT | 75°C (167°F) or more |
| Atmospheric pressure | 570 mmHg or higher |
| A/F sensor status | Activated |
| Continuous time of fuel-cut | 3 to 10 seconds. |
| A/F sensor voltage | More than 3.8 V |
| A/F sensor voltage | Less than 2.8 V |
| A/F sensor current | 3.6 mA or more |
| A/F sensor current | Less than 1.57 mA |
| TLT | CID | Unit Conversion | Description of Test Data | Description of Test Limit |
| 1 | $01 | Multiply by 0.0003 (V) | Cumulative A/F sensor locus length (Bank 1) | Lower malfunction criterion for A/F sensor |
| 0 | $01 | Multiply by 0.0003 (V) | Cumulative A/F sensor locus length (Bank 1) | Upper malfunction criterion for A/F sensor |
| 1 | $11 | Multiply by 0.0003 (V) | Cumulative A/F sensor locus length (Bank 2) | Lower malfunction criterion for A/F sensor |
| 0 | $11 | Multiply by 0.0003 (V) | Cumulative A/F sensor locus length (Bank 2) | Upper malfunction criterion for A/F sensor |
| 1 | $02 | Multiply by 0.000039 (A) | A/F sensor current (Bank 1) | Lower malfunction criterion for A/F sensor |
| 0 | $02 | Multiply by 0.000039 (A) | A/F sensor current (Bank 1) | Upper malfunction criterion for A/F sensor |
| 1 | $12 | Multiply by 0.000039 (A) | A/F sensor current (Bank 2) | Lower malfunction criterion for A/F sensor |
| 0 | $12 | Multiply by 0.000039 (A) | A/F sensor current (Bank 2) | Upper malfunction criterion for A/F sensor |



| Tester Display (Sensor) | Injection Volumes | Status | Voltages |
| AFS B1S1 or AFS B2S1 (A/F) | +25% | Rich | Less than 3.0 |
| AFS B1S1 or AFS B2S1 (A/F) | -12.5% | Lean | More than 3.35 |
| O2S B1S2 or O2S B2S2 (HO2) | +25% | Rich | More than 0.55 |
| O2S B1S2 or O2S B2S2 (HO2) | -12.5% | Lean | Less than 0.4 |
| Case | A/F Sensor (Sensor 1) Output Voltage | HO2 Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area | ||
| 1 | Injection Volume +25% -12.5% | ![]() | Injection Volume +25% -12.5% | ![]() | - |
| Output Voltage More than 3.35 V Less than 3.0 V | ![]() | Output Voltage More than 0.55 V Less than 0.4 V | ![]() | ||
| 2 | Injection Volume +25% -12.5% | ![]() | Injection Volume +25% -12.5% | ![]() |
|
| Output Voltage Almost no reaction | ![]() | Output Voltage More than 0.55 V Less than 0.4 V | ![]() | ||
| 3 | Injection Volume +25% -12.5% | ![]() | Injection Volume +25% -12.5% | ![]() |
|
| Output Voltage More than 3.35 V Less than 3.0 V | ![]() | Output Voltage Almost no reaction | ![]() | ||
| 4 | Injection volume +25% -12.5% | ![]() | Injection Volume +25% -12.5% | ![]() |
|
| Output Voltage Almost no reaction | ![]() | Output Voltage Almost no reaction | ![]() | ||
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P2195, P2196, P2197 OR P2198) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on.
Turn the tester on.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
Read DTCs.
| Display (DTC Output) | Proceed to |
| P2195, P2196, P2197 or P2198 | A |
| P2195, P2196, P2197 or P2198 and other DTCs | B |
|
| ||||
| A | |
| 2.READ VALUE OF INTELLIGENT TESTER (OUTPUT VOLTAGE OF A/F SENSOR) |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Warm up the Air-Fuel Ratio (A/F) sensor at an engine speed of 2,500 rpm for 90 seconds.
Select the following menu items on the tester: DIAGNOSIS / ENHANCED OBD II / SNAPSHOT / MANUAL SNAPSHOT / USER DATA / AFS B1S1 or AFS B2S1 and ENGINE SPD.
Check the A/F sensor voltage 3 times, when the engine is in each of the following conditions:
While idling (check for at least 30 seconds) (Step (1))
At an engine speed of approximately 2,500 rpm (without any sudden changes in engine speed) (Step (2))
Raise the engine speed to 4,000 rpm and then quickly release the accelerator pedal so that the throttle valve is fully closed (Step (3)).
| Conditions | A/F Sensor Voltage Variations | Reference |
| Steps (1) and (2) | Changes at approximately 3.3 V | 3.1 to 3.5 V |
| Step (3) | Increases to 3.8 V or more | This occurs during engine deceleration (when fuel-cut performed) |

|
| ||||
| OK | |
| 3.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 4.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198) |
Read DTCs using the intelligent tester.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
| Display (DTC Output) | Proceed to |
| P2195, P2196, P2197 or P2198 | A |
| No output | B |
|
| ||||
| A | |
| 5.REPLACE AIR FUEL RATIO SENSOR |
| NEXT | |
| 6.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 7.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198) |
Read DTCs using the intelligent tester.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
| Display (DTC Output) | Proceed to |
| No output | A |
| P2195, P2196, P2197 or P2198 | B |
|
| ||||
| A | |
| 8.CONFIRM WHETHER VEHICLE HAS RUN OUT OF FUEL IN PAST |
|
| ||||
| YES | ||
| ||
| 9.INSPECT AIR FUEL RATIO SENSOR |
![]() |
Disconnect the A12 or A13 A/F sensor connector.
Measure the resistance between the terminals of the A/F sensor connector.
| Tester Connections | Specified Conditions |
| HT (1) - +B (2) | 1.8 to 3.4 Ω at 20°C (68°F) |
| HT (1) - AF- (4) | 10 kΩ or higher |
| Tester Connections | Specified Conditions |
| HT (1) - +B (2) | 1.8 to 3.4 Ω at 20°C (68°F) |
| HT (1) - AF- (4) | 10 kΩ or higher |
Reconnect the A/F sensor connector.
|
| ||||
| OK | |
| 10.INSPECT AIR FUEL RATIO SENSOR HEATER RELAY |
![]() |
Remove the A/F sensor heater relay from the engine room R/B.
Check the A/F sensor heater relay resistance.
| Tester Connections | Specified Conditions |
| 3 - 5 | 10 kΩ or higher |
| 3 - 5 | Below 1 Ω (when battery voltage applied to terminals 1 and 2) |
Reinstall the A/F sensor heater relay.
|
| ||||
| OK | |
| 11.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM) |
![]() |
Disconnect the A12 or A13 A/F sensor connector.
Turn the ignition switch on.
Measure the voltage between the +B terminal of the A/F sensor connector and body ground.
| Tester Connections | Specified Conditions |
| +B (A12-2) - Body ground | 9 to 14 V |
| +B (A13-2) - Body ground | 9 to 14 V |
Turn the ignition switch off.
Disconnect the E5 ECM connector.
Measure the resistance between the terminals of A/F sensor connector and ECM connector.
| Tester Connections | Specified Conditions |
| HT (A12-1) - HA1A (E5-2) | Below 1 Ω |
| AF+ (A12-3) - A1A+ (E5-22) | Below 1 Ω |
| AF- (A12-4) - A1A- (E5-30) | Below 1 Ω |
| HT (A13-1) - HA2A (E5-1) | Below 1 Ω |
| AF+ (A13-3) - A2A+ (E5-23) | Below 1 Ω |
| AF- (A13-4) - A2A- (E5-31) | Below 1 Ω |
| Tester Connections | Specified Conditions |
| HA1A (A12-1) or HA1A (E5-2) - Body ground | 10 kΩ or higher |
| A1A+ (A12-3) or A1A+ (E5-22) - Body ground | 10 kΩ or higher |
| A1A- (A12-4) or A1A- (E5-30) - Body ground | 10 kΩ or higher |
| HA2A (A13-1) or HA2A (E5-1) - Body ground | 10 kΩ or higher |
| A2A+ (A13-3) or A2A+ (E5-23) - Body ground | 10 kΩ or higher |
| A2A- (A13-4) or A2A- (E5-31) - Body ground | 10 kΩ or higher |
Reconnect the ECM connector.
Reconnect the A/F sensor connector.

|
| ||||
| OK | |
| 12.CHECK AIR INDUCTION SYSTEM |
Check the air induction system for vacuum leakage.
|
| ||||
| OK | |
| 13.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 14.INSPECT FUEL INJECTOR ASSEMBLY |
Check the injector injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).
|
| ||||
| OK | |
| 15.REPLACE AIR FUEL RATIO SENSOR |
| NEXT | |
| 16.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 17.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198) |
Read DTCs using the intelligent tester.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRET CODES.
| Display (DTC Output) | Proceed to |
| No output | A |
| P2195, P2196, P2197 or P2198 | B |
|
| ||||
| A | |
| 18.CONFIRM WHETHER VEHICLE HAS RUN OUT OF FUEL IN PAST |
|
| ||||
| YES | ||
| ||