AIR CONDITIONING UNIT > REMOVAL |
| 1. DISCHARGE REFRIGERANT FROM REFRIGERATION SYSTEM |
Start up the engine.
Turn the A/C switch on.
Operate the cooler compressor at an engine speed of approximately 1,000 rpm for 5 to 6 minutes to circulate the refrigerant and collect the compressor oil remaining in each component into the cooler compressor.
Stop the engine.
Using SST, discharge the refrigerant gas.
| 2. DISCONNECT COOLER REFRIGERANT SUCTION PIPE C |
Install SST on the piping clamp.
![]() |
Push down SST and release the clamp lock.
Pull SST slightly and push the release lever, and then remove the piping clamp with SST.
![]() |
Disconnect the air conditioning tube assembly.
| 3. DISCONNECT COOLER REFRIGERANT LIQUID PIPE C |
| 4. DISCONNECT HEATER WATER OUTLET HOSE A(FROM HEATER UNIT) |
![]() |
Using pliers, grip the claws of the clip and slide the clip and disconnect the heater water outlet hose A (from the heater unit).
| 5. DISCONNECT HEATER WATER OUTLET HOSE A(FROM HEATER UNIT) |
| 6. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY |
| 7. REMOVE ECM |
| 8. REMOVE AIR CONDITIONING AMPLIFIER ASSEMBLY |
![]() |
Disconnect the connectors.
Remove the 3 screws and air conditioning amplifier assembly.
| 9. REMOVE SIDE DEFROSTER NOZZLE DUCT NO. 1 |
![]() |
Remove the 2 clips.
Release the 2 claw fittings and remove the side defroster nozzle duct No. 1.
| 10. REMOVE SIDE DEFROSTER NOZZLE DUCT NO. 2 |
![]() |
Remove the 2 clips.
Release the 2 claw fittings and remove the side defroster nozzle duct No. 2.
| 11. REMOVE HEATER TO REGISTER DUCT NO. 1 |
![]() |
Remove the screw.
Release the 2 pin fittings and remove the heater to register duct No. 1.
| 12. REMOVE HEATER TO REGISTER DUCT NO. 3 |
![]() |
Remove the screw.
Release the 2 pin fittings and remove the heater to register duct No. 3.
| 13. REMOVE AIR DUCT REAR NO. 1 |
![]() |
Release the 6 claw fittings and 3 clamps and remove the air duct rear No. 2.
| 14. REMOVE AIR DUCT REAR NO. 2 |
![]() |
Release the 6 claw fittings and 3 clamps and remove the air duct rear No. 1.
| 15. DISCONNECT CONSOLE BOX DUCT NO. 1 |
![]() |
Remove the clip and disconnect the console box duct No. 1.
| 16. REMOVE AIR DUCT NO. 1 |
![]() |
Release the 3 claw fittings and remove the air duct No. 1.
| 17. REMOVE AIR DUCT NO. 2 |
![]() |
Release the 3 claw fittings and remove the air duct No. 2.
| 18. REMOVE INSTRUMENT PANEL BRACE MOUNTING BRACKET NO. 1 |
![]() |
Remove the bolt, nut and instrument panel brace mounting bracket No. 1.
![]() |
Remove the bolt, nut and instrument panel brace mounting bracket No. 1.
| 19. DISCONNECT STEERING COLUMN ASSEMBLY |
![]() |
Release the 3 clamps and disconnect the connector.
![]() |
Remove the 4 nuts and disconnect the steering column assembly.
| 20. REMOVE INSTRUMENT PANEL REINFORCEMENT |
Remove the 6 bolts and 8 nuts.

Release the 27 clamps.
Disconnect the connectors.

Remove the 5 bolts.

Remove the 7 bolts and instrument panel reinforcement.

| 21. REMOVE HEATER TO REGISTER DUCT CENTER |
![]() |
Release the 4 claw fittings and remove the heater to register duct center.
| 22. REMOVE DEFROSTER NOZZLE ASSEMBLY LOWER |
![]() |
Release the 4 claw fittings and remove the defroster nozzle assembly lower.
| 23. REMOVE AIR CONDITIONING UNIT ASSEMBLY |
![]() |
Disconnect the connectors.
Remove the 2 nut and air conditioner unit assembly.
| 24. REMOVE AIR CONDITIONING RADIATOR ASSEMBLY |
![]() |
Remove the 2 screws and air conditioning radiator assembly.