Home › TRANSMISSION ยท A750F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION ASSEMBLY (for 1GR-FE)

AUTOMATIC TRANSMISSION ASSEMBLY (for 1GR-FE) > REMOVAL

for Preparation Click here



1. REMOVE NO.1 ENGINE UNDER COVER SUB-ASSEMBLY


2. REMOVE REAR ENGINE UNDER COVER ASSEMBLY


3. DISCONNECT OXYGEN SENSOR

HINT:
(Click here)



4. REMOVE EXHAUST PIPE

HINT:
(Click here)



5. REMOVE FRONT PROPELLER SHAFT ASSEMBLY


    C098708E05
  1. Place matchmarks on the propeller shaft flange and differential.

  1. Remove the 4 nuts, 4 bolts, 4 washers and front propeller shaft assembly.



    C098709E04
  1. Place matchmarks on the propeller shaft flange and transfer flange.

  1. Remove the 4 nuts, 4 washers and front propeller shaft assembly.



6. REMOVE PROPELLER SHAFT ASSEMBLY


    C098711E01
  1. Place matchmarks on the propeller shaft flange and differential flange.

  1. Remove the 4 nuts and 4 washers.



    C098710E02
  1. Remove the propeller shaft.

  1. Insert SST in the transmission to prevent oil leakage.

    SST
    09325-40010  



7. DRAIN AUTOMATIC TRANSMISSION FLUID


    G036650E01
  1. Remove the drain plug and gasket, and drain the ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



8. REMOVE PROPELLER SHAFT HEAT INSULATOR
  1. Remove the 2 bolts and propeller shaft heat insulator.



9. REMOVE FRONT SUSPENSION MEMBER BRACKET


    F042934
  1. Remove the 4 bolts and front suspension member bracket.



10. REMOVE FRONT SUSPENSION MEMBER BRACKET LH
  1. Remove the 4 bolts and front suspension member bracket LH.



11. DISCONNECT NO.1 OIL COOLER OUTLET TUBE


  1. Remove the 2 bolts and 2 clamps.


    G038661

  1. Using SST, disconnect the No. 1 oil cooler outlet tube.

    SST
    09023-12701  



12. REMOVE NO.1 OIL COOLER INLET TUBE


    Z035557E01
  1. Using SST, disconnect the No. 1 oil cooler inlet tube.

    SST
    09023-12701  



13. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    D028154E01
  1. Remove the nut and clip and disconnect the transmission control cable assembly from the No. 1 transmission control cable bracket.



14. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY


    D028162
  1. Support the transmission with a transmission jack.



15. REMOVE NO.3 FRAME CROSSMEMBER SUB-ASSEMBLY


    F042938E02
  1. Remove the 4 nuts, 8 bolts and No. 3 frame crossmember sub-assembly.



16. DISCONNECT CONNECTOR


    D028162
  1. Tilt down the transmission.

    NOTICE:
    Take care so that the cooling fan does not come in contract with the fan shroud.



    G039387E04
  1. Transmission side:

    1. Disconnect the park/neutral position switch connector(a).

    2. Disconnect the transmission wire connector(b).

    3. Disconnect the speed sensor NT connector(c).

    4. Remove the bolt and wire harness from the transmission and transfer.



    5. G038651E04
    6. Disconnect the speed sensor SP2 connector.



  1. Transfer side:



      G039388
    1. Disconnect the transfer shift actuator connector.



17. REMOVE STARTER ASSEMBLY

HINT:
(Click here for Standard or Click here for Cold Area)



18. REMOVE MANIFOLD STAY


19. REMOVE NO.2 MANIFOLD STAY


20. SEPARATE FRONT DIFFERENTIAL ASSEMBLY


    C097020E05
  1. Remove the bolt and separate the front differential breather tube bracket.

  1. Support the front differential with a jack.

  1. Remove the front differential mount nut No. 1.

  1. Remove the 2 front mounting bolts and 2 nuts.

  1. Disconnect the actuator hose and connector.

  1. Lower the jack and remove the front differential assembly.

  1. Remove the 2 bolts and No. 3 front differential support.

  1. Remove the 5 bolts and 2 front differential supports.



21. REMOVE NO.1 REAR ENGINE MOUNTING INSULATOR


    G036651E02
  1. Remove the 4 bolts and No. 1 Rear engine mounting insulator.



22. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY


    F044115
  1. Remove the torque converter housing side cover from the engine.

  1. Turn the crankshaft to gain access to each bolt.

  1. Hold the crankshaft pulley nut with a wrench and remove the 6 bolts.



    D028727E01
  1. Remove the 9 bolts.

  1. Separate and remove the automatic transmission assembly.



23. SEPARATE TRANSFER BREATHER HOSE SUB-ASSEMBLY


    G038385E01
  1. Separate the transfer breather hose sub-assembly from the transmission assembly.



24. REMOVE NO.1 TRANSMISSION CONTROL CABLE BRACKET


    G036547E01
  1. Remove the 2 bolts and No.1 transmission control cable bracket from the transmission assembly.



25. REMOVE TRANSFER ASSEMBLY


    F043500
  1. Remove the 8 bolts and 2 clamps.

  1. Remove the transfer from the automatic transmission.



26. REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY


    G036652
  1. Put matchmarks on the transmission case and torque converter clutch assembly.

  1. Remove the torque converter assembly from the automatic transmission assembly.



27. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY

HINT:
(Click here)

SST
09350-32014   (09351-32010, 09351-32020)