Home › TRANSMISSION ยท A750E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION ASSEMBLY (for 2UZ-FE)

AUTOMATIC TRANSMISSION ASSEMBLY (for 2UZ-FE) > INSTALLATION

for Preparation Click here



1. INSTALL TORQUE CONVERTER CLUTCH ASSEMBLY
  1. Install the torque converter clutch to the automatic transmission.



    D025544E03
  1. Using calipers and a straight edge, measure dimension A between the engine and the end surface of the drive plate.



    D025545E03
  1. Using calipers and a straight edge, measure the dimension B shown in the illustration and check that B is greater than A measured in (b).

    Standard:
    A + 1 mm (0.03937 in.) or more



2. INSTALL NO.1 ENGINE MOUNTING INSULATOR REAR


    F042941
  1. Install the engine mounting insulator rear and 4 bolts to the automatic transmission.

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }



3. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY


    Q003099E01
  1. Install the automatic transmission and 10 bolts to the engine.

    Torque:
    17 mm head:
    71 N*m{ 720 kgf*cm , 53 ft.*lbf }
    14 mm head:
    37 N*m{ 380 kgf*cm , 35 ft.*lbf }



    F042940
  1. Install the 6 torque converter clutch mounting bolts.

    Torque:
    48 N*m{ 490 kgf*cm , 35 ft.*lbf }

    HINT:
    First install black colored bolt and then the 5 bolts.



4. INSTALL FLYWHEEL HOUSING UNDER COVER


    F042939
  1. Install the flywheel housing under cover and 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



5. INSTALL WIRE HARNESS


6. INSTALL NO.3 FRAME CROSSMEMBER SUB-ASSEMBLY


    F042938
  1. Install the No. 3 frame crossmember sub-assembly with 4 bolts and 4 nuts.

    Torque:
    72 N*m{ 734 kgf*cm , 53 ft.*lbf }

  1. Install the No. 3 frame crossmember sub-assembly with 4 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



7. INSTALL NO.1 TRANSMISSION CONTROL CABLE BRACKET


    F042937
  1. Install the No. 1 transmission control cable bracket with 2 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



8. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
  1. Connect the transmission control cable with nut.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



9. INSTALL NO.1 OIL COOLER OUTLET TUBE
  1. Temporarily install the No. 1 oil cooler outlet tube.

  1. Temporarily install the No. 1 oil cooler inlet tube.



    Z035556
  1. Install the 2 clamps and 2 bolts.

    Torque:
    5 N*m{ 50 kgf*cm , 43 in.*lbf }



    Z035557E01
  1. Using SST, tighten the No. 1 oil cooler outlet tube.

    Torque:
    34 N*m{ 346 kgf*cm , 25 ft.*lbf }

    SST
    09023-12701  



10. INSTALL NO.1 OIL COOLER INLET TUBE
  1. Using SST, tighten the No. 1 oil cooler inlet tube.

    Torque:
    34 N*m{ 346 kgf*cm , 25 ft.*lbf }

    SST
    09023-12701  



11. INSTALL FRONT SUSPENSION MEMBER BRACKET LH


    F042934
  1. Install the front suspension member bracket LH with 4 bolts.

    Torque:
    33 N*m{ 336 kgf*cm , 24 ft.*lbf }



12. INSTALL FRONT SUSPENSION MEMBER BRACKET
  1. Install the front suspension member bracket with 4 bolts.

    Torque:
    33 N*m{ 336 kgf*cm , 24 ft.*lbf }



13. INSTALL PROPELLER SHAFT ASSEMBLY


    C098710E03
  1. Remove the SST from the extension housing.

    SST
    09325-40010  

  1. Install the propeller shaft assembly in the extension housing.



    C098711E02
  1. Align the matchmarks on the propeller shaft flange and differential flange.

  1. Install the propeller shaft assembly with the 4 nuts and 4 washers.

    Torque:
    88 N*m{ 897 kgf*cm , 65 ft.*lbf }



14. ADJUST SHIFT LEVER POSITION

HINT:
(Click here)



15. INSTALL EXHAUST PIPE

HINT:
(Click here)



16. INSTALL OXYGEN SENSOR

HINT:
(Click here)



17. INSTALL NO.1 ENGINE UNDER COVER SUB-ASSEMBLY


18. INSTALL ENGINE UNDER COVER ASSEMBLY REAR


19. ADD AUTOMATIC TRANSMISSION FLUID

HINT:
(Click here)



20. ADJUST AUTOMATIC TRANSMISSION FLUID

HINT:
(Click here)



21. INSPECT SHIFT LEVER POSITION

HINT:
(Click here)



22. CHECK FOR EXHAUST GAS LEAKS

HINT:
(Click here)



23. RESET MEMORY

NOTICE:
Perform the RESET MEMORY (AT initialization) when replacing the automatic transmission assembly, engine assembly or ECM (Click here ).

HINT:
RESET MEMORY cannot be completed by only disconnecting the battery terminal.