Home › TRANSMISSION ยท A750F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION ASSEMBLY (for 2UZ-FE)

AUTOMATIC TRANSMISSION ASSEMBLY (for 2UZ-FE) > REMOVAL

for Preparation Click here



1. REMOVE NO.1 ENGINE UNDER COVER SUB-ASSEMBLY


2. REMOVE REAR ENGINE UNDER COVER ASSEMBLY


3. DISCONNECT OXYGEN SENSOR

HINT:
(Click here)



4. REMOVE EXHAUST PIPE

HINT:
(Click here)



5. REMOVE FRONT PROPELLER SHAFT ASSEMBLY


    C098708E05
  1. Place matchmarks on the propeller shaft flange and differential.

  1. Remove the 4 nuts, 4 bolts, 4 washers and front propeller shaft assembly.



    C098709E04
  1. Place matchmarks on the propeller shaft flange and transfer flange.

  1. Remove the 4 nuts, 4 washers and front propeller shaft assembly.



6. REMOVE PROPELLER SHAFT ASSEMBLY


    C098711E01
  1. Place matchmarks on the propeller shaft flange and differential flange.

  1. Remove the 4 nuts and 4 washers.



    C098710E02
  1. Remove the propeller shaft.

  1. Insert SST in the transmission to prevent oil leakage.

    SST
    09325-40010  



7. DRAIN AUTOMATIC TRANSMISSION FLUID
  1. Remove the drain plug, gasket and drain ATF.

  1. Install a new gasket and drain plug.

    Torque:
    28 N*m{ 285 kgf*cm , 21 ft.*lbf }



8. REMOVE FRONT SUSPENSION MEMBER BRACKET


    F042934
  1. Remove the 4 bolts and front suspension member bracket.



9. REMOVE FRONT SUSPENSION MEMBER BRACKET LH
  1. Remove the 4 bolts and front suspension member bracket LH.



10. REMOVE TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY
  1. Remove the ATF level gauge.

  1. Remove the bolt and oil filler tube.

  1. Remove the O-ring from the oil filler tube.



11. DISCONNECT NO.1 OIL COOLER OUTLET TUBE


    Z035556
  1. Remove the 2 bolts and 2 clamps.



    Z035557E01
  1. Using SST, disconnect the No. 1 oil cooler outlet tube.

    SST
    09023-12701  



12. REMOVE NO.1 OIL COOLER INLET TUBE
  1. Using SST, disconnect the No. 1 oil cooler inlet tube.

    SST
    09023-12701  



13. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    F042937
  1. Remove the nut and disconnect the transmission control cable.

  1. Remove the 2 bolts and disconnect the transmission control cable.



14. REMOVE NO.1 TRANSMISSION CONTROL CABLE BRACKET
  1. Remove the 2 bolts and transmission control cable bracket



15. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY


    D028162
  1. Support the automatic transmission assembly with a transmission jack.



16. REMOVE NO.3 FRAME CROSSMEMBER SUB-ASSEMBLY


    F042938
  1. Remove the 4 bolts on the No. 3 frame crossmember sub-assembly.

  1. Remove the 4 nuts, 4 bolts and No. 3 frame crossmember sub-assembly.



17. DISCONNECT CONNECTOR


    D028162
  1. Tilt down the transmission.

    NOTICE:
    Take care so that the cooling fan does not come in contact with the fan shroud.

  1. Disconnect the park/neutral position switch connector.

  1. Disconnect the transmission wire connector.

  1. Disconnect the 2 speed sensor connectors.



18. DISCONNECT WIRE HARNESS


19. REMOVE FLYWHEEL HOUSING UNDER COVER


    F042939
  1. Remove the 2 bolts and flywheel housing under cover.



20. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY


    F042940
  1. Turn the crankshaft to gain access to each bolt.

  1. Hold the crankshaft pulley nut with a wrench and remove the 6 bolts.



    Q003099
  1. Remove the 10 bolts.

  1. Separate and remove the automatic transmission.



21. REMOVE TRANSFER ASSEMBLY


    F043500
  1. Remove the 8 bolts and 2 clamps.

  1. Remove the transfer from the automatic transmission.



22. REMOVE NO.1 REAR ENGINE MOUNTING INSULATOR


    F042941
  1. Remove the 4 bolts and No.1 rear engine mounting insulator from the automatic transmission.



23. REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY


24. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY

HINT:
(Click here)

SST
09350-32014