DTC P0776 Pressure Control Solenoid "B" Performance (Shift Solenoid Valve SL2) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0776 | The gear required by the ECM does not match the actual gear when driving (2-trip detection logic) |
|
| Related DTCs | P0776: Shift solenoid valve SL2/ON malfunction |
| Required sensors/Components (Main) | Shift solenoid valve SL2 |
| Required sensors/Components (Related) | Speed sensor (NT), Speed sensor (NO), Crankshaft position sensor (NE) |
| Frequency of operation | Continuous |
| Duration | ON malfunction (A), (B) and (C): 0.4 sec. ON malfunction (D): 3 sec. ON malfunction (E): 0.5 sec. |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever this DTC is not present. | P0115 - P0118 (ECT sensor) P0125 (Insufficient ECT for Closed Loop) P0500 (VSS) P0748 - P0798 (Trans solenoid (range)) |
| Turbine speed sensor circuit | Not circuit malfunction |
| Output speed sensor circuit | Not circuit malfunction |
| Shift solenoid valve S1 circuit | Not circuit malfunction |
| Shift solenoid valve S2 circuit | Not circuit malfunction |
| Shift solenoid valve SR circuit | Not circuit malfunction |
| Shift solenoid valve SL1 circuit | Not circuit malfunction |
| Shift solenoid valve SL2 circuit | Not circuit malfunction |
| ECT (Engine coolant temperature) sensor circuit | Not circuit malfunction |
| KCS sensor circuit | Not circuit malfunction |
| ETCS (Electric throttle control system) | Not system down |
| Transmission range | "D" |
| ECT | 40°C (104°F) or more |
| Spark advance from Max. retard timing by KCS control | 0° CA or more |
| Engine | Starting |
| ECM selected gear | 1st |
| Vehicle speed | 2 to 40 km/h (1.2 to 24.9 mph) |
| Throttle valve opening angle | 7.0% or more at 2,000 rpm (Vary with engine speed) |
| ECM selected gear | 3rd |
| Vehicle speed | 2 km/h (1.2 mph) or more |
| Throttle valve opening angle | 7.0% or more at 2,000 rpm (Vary with engine speed) |
| ECM selected gear | 4th |
| Vehicle speed | 2 km/h (1.2 mph) or more |
| Throttle valve opening angle | 7.0% or more at 2,000 rpm (Vary with engine speed) |
| Current ECM selected gear | 5th |
| Last ECM selected gear | 4th |
| Vehicle speed (During transition from 4th to 5th gear) | Less than 100 km/h (62.2 mph) |
| ECM selected gear | 5th |
| Engine speed - Turbine speed (NE - NT) (After transition from 4th to 5th gear) | 150 rpm or less |
| Vehicle speed (After transition from 4th to 5th gear) | Less than 100 km/h (62.2 mph) |
| Turbine speed/Output speed | 3.30 to 7.50 |
| Turbine speed/Output speed | 1.28 to 1.53 |
| Turbine speed/Output speed | 0.93 to 1.07 |
| Turbine speed - Output speed x 4th gear ratio (NT - NO x 4th gear ratio) | 1,000 rpm or more |
| Turbine speed - Output speed x 5th gear ratio (NT - NO x 5th gear ratio) | 1,000 rpm or more |
| ACTIVE TEST |
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester together with the CAN VIM (controller area network vehicle interface module) to the DLC3.
Turn the ignition switch to the ON position.
Turn on the tester.
Select the item "DIAGNOSIS / OBD/MOBD / ECT / ACTIVE TEST / SHIFT".
According to the display on the tester, perform the "ACTIVE TEST".
| Item | Test Details | Diagnostic Note |
| SHIFT | [Test Details] Operate the shift solenoid valve and set the each shift position by yourself. [Vehicle Condition]
| Possible to check the operation of the shift solenoid valves. |
| ECM gear shift command | 1st | 2nd | 3rd | 4th | 5th |
| Shift solenoid valve SL2 | ON | ON | ON | ON | OFF |
| 1.CHECK CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P0776) |
Connect the OBD II scan tool or the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and push the OBD II scan tool or the intelligent tester main switch ON.
When you use intelligent tester:
Select the item "DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES".
Read the DTCs using the intelligent tester.
| Display (DTC output) | Proceed to |
| Only "P0776" is output | A |
| "P0776" and other DTCs | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST BY INTELLIGENT TESTER (SHIFT SOLENOID VALVE SLT) |
Turn the ignition switch off.
Lift the vehicle up.
![]() |
Remove the test plug on the transmission case center right side and connect SST.
Lower the vehicle.
Fully apply the parking brake and chock the 4 wheels.
Connect the intelligent tester together with the CAN VIM (controller area network vehicle interface module) to the DLC3.
Start the engine.
Warm up the ATF (Automatic Transmission Fluid).
Measure the line pressure when the engine is idling.
Turn on the tester.
Select the item "DIAGNOSIS / OBD/MOBD / ECT / ACTIVE TEST / SOLENOID (SLT)".
Follow the instructions on the tester and perform the ACTIVE TEST.
Measure the line pressure with SST.
| Item | Test Details |
| LINE PRESS UP* | [Test Details] Operate the shift solenoid SLT and raise the line pressure. [Vehicle Condition]
|
|
| ||||
| OK | |
| 3.INSPECT SHIFT SOLENOID VALVE SL2 |
![]() |
Remove the shift solenoid valve SL2.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition 20°C (68°F) |
| 1 - 2 | 5.0 to 5.6 Ω |
Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.
|
| ||||
| OK | |
| 4.INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
|
| ||||
| OK | ||
| ||