Home › Vehicle Exterior › BODY WELD POINT › FRONT BODY PILLAR
BM1440E _01 Vehicle Exterior _056782 BODY WELD POINT _0276940 FRONT BODY PILLAR F

BODY WELD POINT  FRONT BODY PILLAR  CUT AND JOIN REPLACEMENT SECTIONS  


K122669

Weld work for 980 MPa ultra high strength steel


1.

Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

*a: When welding 2 panels together including 980 MPa ultra high strength steel.

Spot weld Pressure 2940 N (300 kgf, 661 lbf)
Weld current 10000 A
Weld time 18 Cyc. (0.30 Sec.)
Plug weld Plug diameter 10 mm (0.39 in.)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

*b: When welding more than 3 panels together including 980 MPa ultra high strength steel. (When plug welding a panel to the welded panels with the weld condition above.)

Plug weld Plug diameter Same as the standard method (See the introduction)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

HINT:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding. Sufficient weld strength cannot be assured when using 100% CO2 shield gas.



With the cowl top side upper panel removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108819

Remove Weld Points
K108820

Remove Weld Points
K108827

Cut and Join Location
K108828

Cut Location for Supply Parts

REMOVAL POINT
1.

Do not butt weld or heat repair because the heat decreases the strength of areas where ultra high strength steel is used. (See the introduction)

2.

*c indicates welds to remove for easier removal.

3.

*d indicates the location of the foamed sealing material. Be careful when cutting as the foamed sealing material is located near the cutting position.

4.

Remove the remaining foamed sealing material from the vehicles side.


K122705C01
2.146,0.938 2.146,0.49 false 6.521,3.271 6.479,3.042 false 6.458,8.375 6.771,8.573 0.313,0.198 10 false *e 0.698,3.844 1.01,4.042 0.313,0.198 10 false *c 1,4.865 1.313,5.063 0.313,0.198 10 false *c 1.948,4.844 2.26,5.042 0.313,0.198 10 false *c 2.844,4.24 3.156,4.438 0.313,0.198 10 false *c 4.26,1.771 4.573,1.969 0.313,0.198 10 false *c 2.063,0.271 2.375,0.469 0.313,0.198 10 false *d 6.469,3.302 6.698,3.5 0.229,0.198 10 false *d 5.26,1.469 5.938,1.708 0.677,0.24 10 false 125 (4.92)
*e mm (in.) - -


K122706C03
4.323,5.385 4.958,5.698 0.635,0.313 10 false 250 (9.84) 6.594,8.469 6.906,8.667 0.313,0.198 10 false *e
*e mm (in.) - -



INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108824

Plug Weld
K108825

Plug Weld
K108831

Butt Weld
K108834

Body Sealer

INSTALLATION POINT
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

Follow the welding conditions when welding point *a to assure sufficient weld strength. (See the introduction)

4.

Follow the welding conditions when welding point *b to assure sufficient weld strength. (See the introduction)

5.

After welding the side inner panel to the vehicle side, install the front body pillar lower reinforce.

6.

After welding the front body pillar lower reinforce to the vehicle side, install the front body upper outer pillar.

7.

After welding the side inner panel and front body pillar lower reinforce to the vehicle side, install the front body upper outer pillar.

8.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


9.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting / coating)

10.

After welding, apply body sealer to the corresponding parts. (See the painting / coating)

11.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K122707C01
5.573,4.25 4.708,3.854 false 1.125,0.625 1.438,0.823 0.313,0.198 10 false *a 2.031,1.104 2.344,1.302 0.313,0.198 10 false *a 2.531,1.125 2.844,1.323 0.313,0.198 10 false *a 3.052,1.365 3.365,1.563 0.313,0.198 10 false *a 3.146,2.042 3.458,2.24 0.313,0.198 10 false *a 3.042,2.615 3.354,2.813 0.313,0.198 10 false *a 2.823,3 3.135,3.198 0.313,0.198 10 false *a 2.427,3.563 2.74,3.76 0.313,0.198 10 false *a 1.885,3.594 2.198,3.792 0.313,0.198 10 false *a 1.396,3.615 1.708,3.813 0.313,0.198 10 false *a 0.948,3.51 1.26,3.708 0.313,0.198 10 false *a 0.729,3.177 1.042,3.375 0.313,0.198 10 false *a 0.469,2.896 0.781,3.094 0.313,0.198 10 false *a 0.323,2.417 0.635,2.615 0.313,0.198 10 false *a 4.521,3.677 4.771,3.875 0.25,0.198 10 false *1
*1 Side Inner Panel - -


K122708C01
5.302,4.823 4.688,4.313 false 4.531,4.115 4.854,4.313 0.323,0.198 10 false *1 3.531,8.156 3.854,8.354 0.323,0.198 10 false *a 5.885,6.26 6.208,6.458 0.323,0.198 10 false *a
*1 Front Body Pillar Lower Reinforce - -


K122709C01
5.458,3.667 4.875,2.844 false 4.771,2.635 5.073,2.813 0.302,0.177 10 false *1 2.24,6.75 2.542,6.927 0.302,0.177 10 false *b 1.969,8.26 2.271,8.438 0.302,0.177 10 false *b 5.615,5.177 5.917,5.354 0.302,0.177 10 false *b
*1 Front Body Upper Outer Pillar - -