2009-2016 4Runner Service Manual
1GR-FE
Trouble codes (546)
- P0010Open or short in the camshaft timing oil control valve for the intake camshaft (bank 1) circuit (1 trip...
- P0011Valve timing cannot be adjusted when in the advance range (1 trip detection logic).
- P0012Valve timing cannot be adjusted when in the retard range (2 trip detection logic).
- P0013Open or short in the camshaft timing oil control valve for the exhaust camshaft (bank 1) circuit (1 trip...
- P0014Exhaust valve timing is not adjusted in the advance range (2 trip detection logic).
- P0015Exhaust valve timing is not adjusted in the retard range (1 trip detection logic).
- P0016Deviations in the crankshaft position sensor and VVT sensor 1 (for intake camshaft) signals (2 trip detection...
- P0017Deviations in the crankshaft position sensor and VVT sensor 1 (for exhaust camshaft) signals (2 trip...
- P0018Deviations in the crankshaft position sensor and VVT sensor 2 (for intake camshaft) signals (2 trip detection...
- P0019Deviations in the crankshaft position sensor and VVT sensor 2 (for exhaust camshaft) signals (2 trip...
- P0020Open or short in the camshaft timing oil control valve for the intake camshaft (bank 2) circuit (1 trip...
- P0021Valve timing cannot be adjusted when in the advance range (1 trip detection logic).
- P0022Valve timing cannot be adjusted when in the retard range (2 trip detection logic).
- P0023Open or short in the camshaft timing oil control valve for the exhaust camshaft (bank 2) circuit (1 trip...
- P0024Exhaust valve timing is not adjusted in the advance range (2 trip detection logic).
- P0025Exhaust valve timing is not adjusted in the retard range (1 trip detection logic).
- P0031Air fuel ratio sensor heater current is below 0.8 A (1 trip detection logic).
- P0032Air fuel ratio sensor heater current failure (1 trip detection logic).
- P0037The heater current is below the specified value while the heater is operating (1 trip detection logic).
- P0038The heater current is higher than the specified value while the heater is operating (1 trip detection logic).
- P0051Air fuel ratio sensor heater current is below 0.8 A (1 trip detection logic).
- P0052Air fuel ratio sensor heater current failure (1 trip detection logic).
- P0057The heater current is below the specified value while the heater is operating (1 trip detection logic).
- P0058The heater current is higher than the specified value while the heater is operating (1 trip detection logic).
- P0102Mass air flow meter voltage is below 0.2 V for 3 seconds (1 trip detection logic: Engine speed is less than...
- P0103Mass air flow meter voltage is higher than 4.9 V for 3 seconds (1 trip detection logic: Engine speed is less...
- P0112Short in the intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic).
- P0113Open in the intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic).
- P0115Open or short in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic).
- P0116Engine coolant temperature is between 35°C and 60°C (95°F and 140°F) when the engine is started and...
- P0117Short in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic).
- P0118Open in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic).
- P0120Output voltage of VTA1 quickly fluctuates beyond the lower and upper malfunction thresholds for 2 seconds...
- P0121Difference between VTA1 and VTA2 voltages is less than 0.8 V, or more than 1.6 V for 2 seconds (1 trip...
- P0122Output voltage of VTA1 is 0.2 V or less for 2 seconds when the accelerator pedal is depressed (1 trip...
- P0123Output voltage of VTA1 is 4.54 V or higher for 2 seconds when the accelerator pedal is depressed (1 trip...
- P0137· Low voltage (open): During active air-fuel ratio control, conditions (a) and (b) are met for a certain...
- P0157· Low voltage (open): During active air-fuel ratio control, conditions (a) and (b) are met for a certain...
- P0220Output voltage of VTA2 quickly fluctuates beyond the lower and upper malfunction thresholds for 2 seconds...
- P0222Output voltage of VTA2 is 1.75 V or less for 2 seconds when the accelerator pedal is depressed (1 trip...
- P0223Output voltage of VTA2 is 4.8 V or higher, and VTA1 is between 0.2 V and 2.02 V for 2 seconds when the...
- P0230Either condition is met (1 trip detection logic): · When the fuel pump is operating: · Amount of remaining...
- P0327Output voltage of the knock sensor is below 0.5 V (1 trip detection logic).
- P0328Output voltage of the knock sensor is higher than 4.5 V (1 trip detection logic).
- P0332Output voltage of the knock sensor is below 0.5 V (1 trip detection logic).
- P0333Output voltage of the knock sensor is higher than 4.5 V (1 trip detection logic).
- P0335Either condition is met: · No crankshaft position sensor signal is sent to the ECM while cranking (1 trip...
- P0339Under conditions (a), (b) and (c), no crankshaft position sensor signal is sent to the ECM for 0.05 seconds...
- P0340Either condition is met: · No VVT sensor signal is sent to the ECM while cranking (2 trip detection logic). ·...
- P0342Output voltage of the VVT sensor is below 0.3 V for 4 seconds (1 trip detection logic).
- P0343Output voltage of the VVT sensor is higher than 4.7 V for 4 seconds (1 trip detection logic).
- P0345There is no VVT sensor signal despite the crankshaft position sensor input being normal at an engine speed of...
- P0347Output voltage of the VVT sensor is below 0.3 V for 4 seconds (1 trip detection logic).
- P0348Output voltage of the VVT sensor is higher than 4.7 V for 4 seconds (1 trip detection logic).
- P0351No IGF signal is sent to the ECM while the engine is running (1 trip detection logic).
- P0352No IGF signal is sent to the ECM while the engine is running (1 trip detection logic).
- P0353No IGF signal is sent to the ECM while the engine is running (1 trip detection logic).
- P0354No IGF signal is sent to the ECM while the engine is running (1 trip detection logic).
- P0355No IGF signal is sent to the ECM while the engine is running (1 trip detection logic).
- P0356No IGF signal is sent to the ECM while the engine is running (1 trip detection logic).
- P0365There is no VVT sensor signal despite the crankshaft position sensor input being normal at an engine speed of...
- P0367Output voltage of the VVT sensor is below 0.3 V for 4 seconds (1 trip detection logic).
- P0368Output voltage of the VVT sensor is higher than 4.7 V for 4 seconds (1 trip detection logic).
- P0390There is no VVT sensor signal despite the crankshaft position sensor input being normal at an engine speed of...
- P0392Output voltage of the VVT sensor is below 0.3 V for 4 seconds (1 trip detection logic).
- P0393Output voltage of the VVT sensor is higher than 4.7 V for 4 seconds (1 trip detection logic).
- P0412All conditions are met for 3 seconds or more while idling immediately after the engine is started (1 trip...
- P0416Open or short in the air injection VSV relay (AI-VSV) circuit for 3 seconds (1 trip detection logic).
- P0417Open or short in the air injection VSV relay (AI-VSV) circuit for 3 seconds (1 trip detection logic).
- P0443Terminal voltage of ECM output circuit does not correspond with drive signals from ECM to purge VSV (1 trip...
- P0452EVAP pressure is below 42.1 kPa for 0.5 seconds.
- P0453EVAP pressure is higher than 123.8 kPa for 0.5 seconds.
- P0500While the vehicle is being driven, no vehicle speed sensor signal is transmitted to the ECM (2 trip detection...
- P0504Conditions (a), (b) and (c) are met for 0.5 seconds or more (1 trip detection logic): (a) Ignition switch is...
- P0504Conditions (a), (b) and (c) are met for 0.5 seconds or more (1 trip detection logic): (a) Ignition switch is...
- P0505Idling speed continues to vary greatly from the target idling speed (2 trip detection logic).
- P0550Power steering oil pressure switch voltage is below 0.28 V, or higher than 4.9 V for 0.5 seconds while the...
- P0552Power steering oil pressure switch voltage is below 0.28 V for 0.5 seconds while the engine is running (1...
- P0553Power steering oil pressure switch voltage is higher than 4.9 V for 0.5 seconds while the engine is running...
- P0560Open in the ECM backup power source circuit (1 trip detection logic).
- P0604There is an ECM internal error (1 trip detection logic).
- P0606There is an ECM internal error (1 trip detection logic).
- P060AThere is an ECM internal error (1 trip detection logic).
- P060BThere is an ECM internal error (1 trip detection logic).
- P060DThere is an ECM internal error (1 trip detection logic).
- P060EThere is an ECM internal error (1 trip detection logic).
- P0617Conditions (a), (b) and (c) are met, and a positive (+B) battery voltage of 10.5 V or higher is applied to...
- P0617Conditions (a), (b) and (c) are met, and a positive (+B) battery voltage of 10.5 V or higher is applied to...
- P0657There is an ECM internal error (1 trip detection logic).
- P0724Stop light switch remains on even when the vehicle is driven in a GO (30 km/h (18.65 mph) or more) and STOP...
- P0724Stop light switch remains on even when the vehicle is driven in a GO (30 km/h (18.65 mph) or more) and STOP...
- P101DThe heater current is higher than the specified value while the heater is not operating (1 trip detection...
- P102DThe heater current is higher than the specified value while the heater is not operating (1 trip detection...
- P103DThe heater current is higher than the specified value while the heater is not operating (1 trip detection...
- P105DThe heater current is higher than the specified value while the heater is not operating (1 trip detection...
- P144COpen or short in the air pump heater relay (AIR PUMP HTR) circuit for 5 seconds (1 trip detection logic).
- P144DOpen or short in the air pump heater relay (AIR PUMP HTR) circuit for 5 seconds (1 trip detection logic).
- P1603After monitoring for startability problems (P1604) finishes and 2 seconds or more have elapsed after starting...
- P1603After monitoring for startability problems (P1604) finishes and 5 seconds or more elapse after starting the...
- P1604Either condition is met: · The engine speed is less than 500 rpm with the STA signal on for a certain amount...
- P1604Either conditions is met (1 trip detection logic): · The engine speed is below 500 rpm with the STA signal on...
- P1605After 5 seconds or more elapse after starting the engine, with the engine running, the engine speed drops to...
- P1605When idling with the accelerator pedal released and the vehicle stopped, this item detects when the...
- P1607There is an ECM internal error (1 trip detection logic).
- P1613Either condition (1) or (2) is met: (1) All conditions are met for 3 seconds or more (1 trip detection...
- P2102Conditions (a) and (b) are met for 2.0 seconds (1 trip detection logic): (a) Throttle actuator duty ratio is...
- P2103Either condition is met (1 trip detection logic): · There is a hybrid IC diagnosis signal failure. · There is...
- P2109Either condition is met: · With the mass air flow meter normal and atmospheric pressure 85 kPa (638 mmHg) or...
- P2111Throttle actuator does not close when signaled by the ECM (1 trip detection logic).
- P2112Throttle actuator does not open when signaled by the ECM (1 trip detection logic).
- P2118Open in the ETCS power source (+BM) circuit (1 trip detection logic).
- P2119Throttle valve opening angle continues to vary greatly from the target opening angle (1 trip detection logic).
- P2120VPA fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more (1 trip...
- P2121Difference between VPA and VPA2 is less than 0.4 V, or more than 1.2 V for 0.5 seconds (1 trip detection...
- P2122VPA is 0.4 V or less for 0.5 seconds or more when the accelerator pedal is fully released (1 trip detection...
- P2123VPA is 4.8 V or higher for 2.0 seconds or more (1 trip detection logic).
- P2125VPA2 fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more (1 trip...
- P2127VPA2 is 1.2 V or less for 0.5 seconds or more when the accelerator pedal is fully released (1 trip detection...
- P2128Conditions (a) and (b) are met for 2.0 seconds or more (1 trip detection logic): (a) VPA2 is 4.8 V or higher....
- P2135Either condition is met (1 trip detection logic): (a) Difference between the output voltages of VTA1 and VTA2...
- P2138Condition (a) or (b) is met for 2.0 seconds or more (1 trip detection logic): (a) Difference between VPA and...
- P2237Open in the circuit between terminals AF+ and AF- of the air fuel ratio sensor while the engine is running (2...
- P2237Open in the circuit between terminals AF+ and AF- of the air fuel ratio sensor while the engine is running (2...
- P2238· Case 1: Condition (a) or (b) is met for 5.0 seconds or more (2 trip detection logic): (a) AF+ voltage is...
- P2238· Case 1: Condition (a) or (b) is met for 5.0 seconds or more (2 trip detection logic): (a) AF+ voltage is...
- P2239AF+ voltage is higher than 4.5 V for 5.0 seconds or more (2 trip detection logic).
- P2239AF+ voltage is higher than 4.5 V for 5.0 seconds or more (2 trip detection logic).
- P2240Open in the circuit between terminals AF+ and AF- of the air fuel ratio sensor while the engine is running (2...
- P2240Open in the circuit between terminals AF+ and AF- of the air fuel ratio sensor while the engine is running (2...
- P2241· Case 1: Condition (a) or (b) is met for 5.0 seconds or more (2 trip detection logic): (a) AF+ voltage is...
- P2241· Case 1: Condition (a) or (b) is met for 5.0 seconds or more (2 trip detection logic): (a) AF+ voltage is...
- P2242AF+ voltage is higher than 4.5 V for 5.0 seconds or more (2 trip detection logic).
- P2242AF+ voltage is higher than 4.5 V for 5.0 seconds or more (2 trip detection logic).
- P2252AF- voltage is 0.5 V or less for 5.0 seconds or more (2 trip detection logic).
- P2252AF- voltage is 0.5 V or less for 5.0 seconds or more (2 trip detection logic).
- P2253AF- voltage is higher than 4.5 V for 5.0 seconds or more (2 trip detection logic).
- P2253AF- voltage is higher than 4.5 V for 5.0 seconds or more (2 trip detection logic).
- P2255AF- voltage is 0.5 V or less for 5.0 seconds or more (2 trip detection logic).
- P2255AF- voltage is 0.5 V or less for 5.0 seconds or more (2 trip detection logic).
- P2256AF- voltage is higher than 4.5 V for 5.0 seconds or more (2 trip detection logic).
- P2256AF- voltage is higher than 4.5 V for 5.0 seconds or more (2 trip detection logic).
- P2431Pressure sensor indicates a value below 45.6 kPa (342 mmHg), or higher than 135 kPa (1013 mmHg) (2 trip...
- P2432While the engine is running, the voltage output of the pressure sensor is below 0.5 V (1 trip detection...
- P2433While the engine is running, the voltage output of the pressure sensor is higher than 4.5 V (1 trip detection...
- P2436Pressure sensor indicates a value below 45.6 kPa (342 mmHg), or higher than 135 kPa (1013 mmHg) (2 trip...
- P2437While the engine is running, the voltage output of the pressure sensor is below 0.5 V (1 trip detection...
- P2438While the engine is running, the voltage output of the pressure sensor is higher than 4.5 V (1 trip detection...
- P2440Cumulative pressure pulsation is 60 kPa (450 mmHg) or more for 2 seconds (1 trip detection logic).
- P2441The emission control valve set (for bank 1) is stuck closed for 7 seconds while the engine is running (2 trip...
- P2442Cumulative pressure pulsation is 60 kPa (450 mmHg) or more for 2 seconds (1 trip detection logic).
- P2443The NO. 2 emission control valve set (for bank 2) is stuck closed for 7 seconds while the engine is running...
- P2445Both of the following conditions are met for 7 seconds (2 trip detection logic): (a) Engine is running (b)...
- P2610There is an ECM internal malfunction.
- P0500The vehicle speed signal from the skid control ECU is cut for 0.14 seconds or more while cruise control is in...
- P0503A malfunction in the vehicle speed signal is detected while cruise control is in operation.
- P0571The voltages of terminals ST1- and STP of the ECM are both below 1 V for 0.5 seconds or more.
- P0571The voltages of terminals ST1- and STP of the ECM are both below 1 V for 0.5 seconds or more.
- P0575Either condition is met: · The cruise control input signal is abnormal. · The stop light switch input signal...
- P0705One of the following conditions is met: (A) Any 2 or more of the following signals are ON simultaneously...
- P0712ATF temperature sensor resistance is below 79 Ω for 0.5 sec. or more (1-trip detection logic).
- P0713ATF temperature sensor resistance is higher than 156 kΩ for 0.5 sec. or more and either condition is met...
- P0717All conditions are met for 5 sec. or more (1-trip detection logic): (a) Gear change: not performed. (b) Gear...
- P0722All conditions are met 500 times or more continuously (2-trip detection logic): (a) No signal from speed...
- P0748The ECM checks for an open or short in the shift solenoid valve SL1 circuit while driving and shifting...
- P0751Gear required by the ECM does not match the actual gear when driving (1-trip detection logic).
- P0756Gear required by ECM does not match actual gear when driving (1-trip detection logic).
- P0771The gear required by the ECM does not match the actual gear when driving (1-trip detection logic).
- P0776Gear required by the ECM does not match the actual gear when driving (1-trip detection logic).
- P0778The ECM checks for an open or short in the shift solenoid valve SL2 circuit while driving and shifting gears...
- P0781Gear required by the ECM does not match the actual gear when driving (1-trip detection logic).
- P0973The ECM detects a short in the solenoid valve S1 circuit 2 times when solenoid valve S1 is operated (1-trip...
- P0974The ECM detects an open in the solenoid valve S1 circuit 2 times when solenoid valve S1 is not operated...
- P0976The ECM detects a short in the solenoid valve S2 circuit 2 times when solenoid valve S2 is operated (1-trip...
- P0977The ECM detects an open in the solenoid valve S2 circuit 2 times when solenoid valve S2 is not operated...
- P0985The ECM detects a short in the solenoid valve SR circuit 2 times when solenoid valve SR is operated (1-trip...
- P0986The ECM detects an open in the solenoid valve SR circuit 2 times when solenoid valve SR is not operated...
- P2714The ECM detects a malfunction of SLT (ON side) according to the difference in speed between the turbine and...
- P2716Open or short is detected in the shift solenoid valve SLT circuit for 1 sec. or more while driving (1-trip...
- P2742No. 2 ATF temperature sensor resistance is below 25 Ω (0.046 V) for 0.5 sec. or more (1-trip detection logic).
- P2743ATF temperature sensor resistance is higher than 156 kΩ (4.915 V) for 0.5 sec. or more and either condition...
- P2759Open or short is detected in the shift solenoid valve SLU circuit for 1 sec. or more while driving (1-trip...
- P0705One of the following conditions is met: (A) Any 2 or more of the following signals are ON simultaneously...
- P0712ATF temperature sensor resistance is below 79 Ω for 0.5 sec. or more (1-trip detection logic).
- P0713ATF temperature sensor resistance is higher than 156 kΩ for 0.5 sec. or more and either condition is met...
- P0717All conditions are met for 5 sec. or more (1-trip detection logic): (a) Gear change: not performed. (b) Gear...
- P0722All conditions are met 500 times or more continuously (2-trip detection logic): (a) No signal from speed...
- P0748The ECM checks for an open or short in the shift solenoid valve SL1 circuit while driving and shifting...
- P0751Gear required by the ECM does not match the actual gear when driving (1-trip detection logic).
- P0756Gear required by ECM does not match actual gear when driving (1-trip detection logic).
- P0771The gear required by the ECM does not match the actual gear when driving (1-trip detection logic).
- P0776Gear required by the ECM does not match the actual gear when driving (1-trip detection logic).
- P0778The ECM checks for an open or short in the shift solenoid valve SL2 circuit while driving and shifting gears...
- P0781Gear required by the ECM does not match the actual gear when driving (1-trip detection logic).
- P0973The ECM detects a short in the solenoid valve S1 circuit 2 times when solenoid valve S1 is operated (1-trip...
- P0974The ECM detects an open in the solenoid valve S1 circuit 2 times when solenoid valve S1 is not operated...
- P0976The ECM detects a short in the solenoid valve S2 circuit 2 times when solenoid valve S2 is operated (1-trip...
- P0977The ECM detects an open in the solenoid valve S2 circuit 2 times when solenoid valve S2 is not operated...
- P0985The ECM detects a short in the solenoid valve SR circuit 2 times when solenoid valve SR is operated (1-trip...
- P0986The ECM detects an open in the solenoid valve SR circuit 2 times when solenoid valve SR is not operated...
- P2714The ECM detects a malfunction of SLT (ON side) according to the difference in speed between the turbine and...
- P2716Open or short is detected in the shift solenoid valve SLT circuit for 1 sec. or more while driving (1-trip...
- P2742No. 2 ATF temperature sensor resistance is below 25 Ω (0.046 V) for 0.5 sec. or more (1-trip detection logic).
- P2743ATF temperature sensor resistance is higher than 156 kΩ (4.915 V) for 0.5 sec. or more and either condition...
- P2759Open or short is detected in the shift solenoid valve SLU circuit for 1 sec. or more while driving (1-trip...
- C0226An open or short circuit in the SFRH or SFRR circuit continues for 0.05 seconds or more.
- C0226An open or short circuit in the SFRH or SFRR circuit continues for 0.05 seconds or more.
- C0236An open or short circuit in the SFLH or SFLR circuit continues for 0.05 seconds or more.
- C0236An open or short circuit in the SFLH or SFLR circuit continues for 0.05 seconds or more.
- C0246An open or short circuit in the SRRH or SRRR circuit continues for 0.05 seconds or more.
- C0246An open or short circuit in the SRRH or SRRR circuit continues for 0.05 seconds or more.
- C0256An open or short circuit in the SRLH or SRLR circuit continues for 0.05 seconds or more.
- C0256An open or short circuit in the SRLH or SRLR circuit continues for 0.05 seconds or more.
- C0278Either condition is met: 1. Both of the following conditions continue for at least 0.2 seconds. 1. IG voltage...
- C0278Either condition is met: 1. Both of the following conditions continue for at least 0.2 seconds. 1. IG voltage...
- C0279The following condition continues for at least 0.2 seconds. · The relay contact is closed immediately after...
- C0279The following condition continues for at least 0.2 seconds. · The relay contact is closed immediately after...
- C0371Stored during test mode.
- C1201A malfunction signal is received from the ECM.
- C1203The engine/drivetrain specification and/or destination information from the ECM does not match the skid...
- C120AThe master cylinder solenoid is not informed that the vehicle is equipped with downhill assist control and...
- C120AThe master cylinder solenoid is not informed that the vehicle is equipped with downhill assist control and...
- C1210Zero point calibration of the yaw rate sensor is incomplete.
- C1210Zero point calibration of the yaw rate sensor is incomplete.
- C1225An open or short circuit in the SMCF circuit continues for 0.05 seconds or more.
- C1225An open or short circuit in the SMCF circuit continues for 0.05 seconds or more.
- C1226An open or short circuit in the SREA circuit continues for 0.05 seconds or more.
- C1226An open or short circuit in the SREA circuit continues for 0.05 seconds or more.
- C1227An open or short circuit in the SREC circuit continues for 0.05 seconds or more.
- C1227An open or short circuit in the SREC circuit continues for 0.05 seconds or more.
- C1228An open or short circuit in the STR circuit continues for 0.05 seconds or more.
- C1228An open or short circuit in the STR circuit continues for 0.05 seconds or more.
- C1232At a vehicle speed of 10 km/h (6 mph) or more, the fluctuation range of the signal from one of either GL1 or...
- C1232At a vehicle speed of 10 km/h (6 mph) or more, the fluctuation range of the signal from one of either GL1 or...
- C1240The yaw rate and acceleration sensor identification information memorized by the skid control ECU does not...
- C1240The yaw rate and acceleration sensor identification information memorized by the skid control ECU does not...
- C1241Either condition is met: 1. Both of the following conditions continue for at least 10 seconds. · The vehicle...
- C1241Either condition is met: 1. Both of the following conditions continue for at least 10 seconds. · The vehicle...
- C1242The vehicle speed is 3 km/h (2 mph) or more and the voltage at the ECU IG2 terminal remains below 6.5 V for...
- C1242The vehicle speed is 3 km/h (2 mph) or more and the voltage at the ECU IG2 terminal remains below 6.5 V for...
- C1243The following condition repeats 16 times. · GL1 and GL2 do not change when the vehicle decelerates from 30...
- C1243The following condition repeats 16 times. · GL1 and GL2 do not change when the vehicle decelerates from 30...
- C1245The following condition continues for at least 60 seconds. · The difference between the values calculated...
- C1245The following condition continues for at least 60 seconds. · The difference between the values calculated...
- C1251There is an open in the motor system circuit (motor input circuit).
- C1251There is an open in the motor system circuit (motor input circuit).
- C1252The motor operates for 3 minutes or more.
- C1252The motor operates for 3 minutes or more.
- C1253There is a motor system circuit (motor input circuit) malfunction.
- C1253There is a motor system circuit (motor input circuit) malfunction.
- C1254There is an accumulator pressure sensor malfunction (the fluid pressure does not change when the pump...
- C1254There is an accumulator pressure sensor malfunction (the fluid pressure does not change when the pump...
- C1256The fluid pressure inside the accumulator is below the standard value.
- C1256The fluid pressure inside the accumulator is below the standard value.
- C1257There is an open in the motor system circuit (motor input circuit).
- C1257There is an open in the motor system circuit (motor input circuit).
- C1268The skid control ECU receives an L4 abnormal status signal from the four wheel drive control ECU via CAN.
- C1268The skid control ECU receives an L4 abnormal status signal from the four wheel drive control ECU via CAN.
- C1271Stored only during test mode.
- C1271Stored only during test mode.
- C1272Stored only during test mode.
- C1272Stored only during test mode.
- C1273Stored only during test mode.
- C1273Stored only during test mode.
- C1274Stored only during test mode.
- C1274Stored only during test mode.
- C1275Stored only during test mode.
- C1275Stored only during test mode.
- C1276Stored only during test mode.
- C1276Stored only during test mode.
- C1277Stored only during test mode.
- C1277Stored only during test mode.
- C1278Stored only during test mode.
- C1278Stored only during test mode.
- C1279Stored during test mode.
- C1279Stored during test mode.
- C1281Stored only during test mode.
- C1282Stored during test mode.
- C1282Stored during test mode.
- C1283Stored only during test mode.
- C1283Stored only during test mode.
- C1290The steering angle sensor zero point calibration position vastly differs from the recorded value.
- C1336Zero point calibration of the acceleration sensor is incomplete.
- C1336Zero point calibration of the acceleration sensor is incomplete.
- C1337Either condition is met: · The diameter of 2 front wheels and 2 rear wheels is different. · There is a wheel...
- C1337Either condition is met: · The diameter of 2 front wheels and 2 rear wheels is different. · There is a wheel...
- C1340An open circuit is detected in the EXI circuit of the skid control ECU.
- C1340An open circuit is detected in the EXI circuit of the skid control ECU.
- C1379Stored only during test mode.
- C1379Stored only during test mode.
- C1380Either condition is met: · When the voltage at the IG1 terminal is between 10 V and 14 V, the stop light...
- C1380Either condition is met: · When the voltage at the IG1 terminal is between 10 V and 14 V, the stop light...
- C1380· When the voltage at the IG1 terminal is 9.5 V or more and the stop light control relay drive output (STPO)...
- C1381At a vehicle speed of more than 3 km/h (2 mph), the acceleration sensor power source malfunction signal is...
- C1381At a vehicle speed of more than 3 km/h (2 mph), the acceleration sensor power source malfunction signal is...
- C1401One of the following conditions is met: 1. At a vehicle speed of 10 km/h (6 mph) or more, the output voltage...
- C1401One of the following conditions is met: 1. At a vehicle speed of 10 km/h (6 mph) or more, the output voltage...
- C1402One of the following conditions is met: 1. At a vehicle speed of 10 km/h (6 mph) or more, the output voltage...
- C1402One of the following conditions is met: 1. At a vehicle speed of 10 km/h (6 mph) or more, the output voltage...
- C1403One of the following conditions is met: 1. At a vehicle speed of 10 km/h (6 mph) or more, the output voltage...
- C1403One of the following conditions is met: 1. At a vehicle speed of 10 km/h (6 mph) or more, the output voltage...
- C1404One of the following conditions is met: 1. At a vehicle speed of 10 km/h (6 mph) or more, the output voltage...
- C1404One of the following conditions is met: 1. At a vehicle speed of 10 km/h (6 mph) or more, the output voltage...
- C1405Either condition is met: 1. An open in the speed sensor signal circuit continues for 0.5 seconds or more. 2....
- C1405Either condition is met: 1. An open in the speed sensor signal circuit continues for 0.5 seconds or more. 2....
- C1406Either condition is met: 1. An open in the speed sensor signal circuit continues for 0.5 seconds or more. 2....
- C1406Either condition is met: 1. An open in the speed sensor signal circuit continues for 0.5 seconds or more. 2....
- C1407Either condition is met: 1. An open in the speed sensor signal circuit continues for 0.5 seconds or more. 2....
- C1407Either condition is met: 1. An open in the speed sensor signal circuit continues for 0.5 seconds or more. 2....
- C1408Either condition is met: 1. An open in the speed sensor signal circuit continues for 0.5 seconds or more. 2....
- C1408Either condition is met: 1. An open in the speed sensor signal circuit continues for 0.5 seconds or more. 2....
- C1409One of the following conditions is met: 1. When the vehicle is driven in reverse at a speed of 3 km/h (2 mph)...
- C1409One of the following conditions is met: 1. When the vehicle is driven in reverse at a speed of 3 km/h (2 mph)...
- C1410One of the following conditions is met: 1. When the vehicle is driven in reverse at a speed of 3 km/h (2 mph)...
- C1410One of the following conditions is met: 1. When the vehicle is driven in reverse at a speed of 3 km/h (2 mph)...
- C1411One of the following conditions is met: 1. When the vehicle is driven in reverse at a speed of 3 km/h (2 mph)...
- C1411One of the following conditions is met: 1. When the vehicle is driven in reverse at a speed of 3 km/h (2 mph)...
- C1412One of the following conditions is met: 1. When the vehicle is driven in reverse at a speed of 3 km/h (2 mph)...
- C1412One of the following conditions is met: 1. When the vehicle is driven in reverse at a speed of 3 km/h (2 mph)...
- C1413One of the following condition is met: 1. An open in the sensor signal circuit of a malfunctioning area...
- C1413One of the following condition is met: 1. An open in the sensor signal circuit of a malfunctioning area...
- C1414One of the following condition is met: 1. An open in the sensor signal circuit of a malfunctioning area...
- C1414One of the following condition is met: 1. An open in the sensor signal circuit of a malfunctioning area...
- C1415One of the following conditions is met: 1. An open in the sensor signal circuit of a malfunctioning area...
- C1415One of the following conditions is met: 1. An open in the sensor signal circuit of a malfunctioning area...
- C1416One of the following conditions is met: 1. An open in the sensor signal circuit of a malfunctioning area...
- C1416One of the following conditions is met: 1. An open in the sensor signal circuit of a malfunctioning area...
- C1417The IG1 terminal voltage is 17.4 V or higher for 0.8 seconds or more.
- C1417The IG1 terminal voltage is 17.4 V or higher for 0.8 seconds or more.
- C1419A data malfunction signal is received from the acceleration sensor.
- C1419A data malfunction signal is received from the acceleration sensor.
- C1420After the difference between GL1 and GL2 becomes 0.6 G or more with the vehicle stationary, the difference...
- C1420After the difference between GL1 and GL2 becomes 0.6 G or more with the vehicle stationary, the difference...
- C1421Either condition is met: Both of the following conditions continue for at least 1.2 seconds. · The IG1...
- C1422When the stop light switch is off, the PM/C1 terminal voltage is 0.86 V or higher for 5 seconds or more.
- C1422When the stop light switch is off, the PM/C1 terminal voltage is 0.86 V or higher for 5 seconds or more.
- C1423Both of the following conditions continue for at least 5 seconds · The stop light switch is off. · The PM/C1...
- C1424One of the following condition is met: · Noise occurs in the signal from the signal from the PM/C1 terminal 7...
- C1425When the IG1 terminal voltage is between 9.5 and 17.4 V and the skid control ECU STPO terminal output is off,...
- C1425When the IG1 terminal voltage is between 9.5 and 17.4 V and the skid control ECU STPO terminal output is off,...
- C1432A steering angle sensor power supply malfunction signal is received from the steering angle sensor.
- C1433Either condition is met: 1. With the IG1 terminal voltage at 9.5 to 17.4 V, the skid control ECU receives an...
- C1433Either condition is met: 1. With the IG1 terminal voltage at 9.5 to 17.4 V, the skid control ECU receives an...
- C1434An error in communication between the skid control ECU and the steering angle sensor, or an abnormal steering...
- C1434An error in communication between the skid control ECU and the steering angle sensor, or an abnormal steering...
- C1435A data malfunction signal is received from the yaw rate and acceleration sensor.
- C1435A data malfunction signal is received from the yaw rate and acceleration sensor.
- C1436Either condition is met: 1. With the vehicle stationary, the yaw rate and acceleration sensor output value is...
- C1436Either condition is met: 1. With the vehicle stationary, the yaw rate and acceleration sensor output value is...
- C1437When the IG1 terminal voltage is 10 V or higher and the vehicle speed is 15 km/h (9 mph) or more, data cannot...
- C1437When the IG1 terminal voltage is 10 V or higher and the vehicle speed is 15 km/h (9 mph) or more, data cannot...
- C1439After the steering angle sensor zero point calibration is cleared due to, for example, fluctuations in the...
- C1439After the steering angle sensor zero point calibration is cleared due to, for example, fluctuations in the...
- C1440Driving at a steep bank angle
- C1440Driving at a steep bank angle
- C1442An invalid data signal is transmitted continuously from the acceleration sensor for 10 seconds or more.
- C1442An invalid data signal is transmitted continuously from the acceleration sensor for 10 seconds or more.
- C1443An invalid data signal is transmitted continuously from the yaw rate and acceleration sensor for 10 seconds...
- C1443An invalid data signal is transmitted continuously from the yaw rate and acceleration sensor for 10 seconds...
- C1445Steering angle sensor zero point calibration cannot be obtained when the vehicle is driven without a record...
- C1445Steering angle sensor zero point calibration cannot be obtained when the vehicle is driven without a record...
- C1452After braking, the fluid pressure inside the accumulator is below the threshold within 3.2 seconds.
- C1452After braking, the fluid pressure inside the accumulator is below the threshold within 3.2 seconds.
- C1453With the ECU terminal IG1 voltage at 10 to 14 V, an open in the brake fluid level warning switch circuit...
- C1453With the ECU terminal IG1 voltage at 10 to 14 V, an open in the brake fluid level warning switch circuit...
- C1454The fluid level of the reservoir is LOW for 40 seconds after the ignition switch is turned to ON, or for 7...
- C1454The fluid level of the reservoir is LOW for 40 seconds after the ignition switch is turned to ON, or for 7...
- C1455The IG1 terminal voltage is 9.5 V or higher and the PCTRL terminal voltage is outside the range of 0.19 to...
- C1456When the stop light switch is off, the PCTRL terminal voltage is 0.86 V or higher for 5 seconds or more.
- C1456When the stop light switch is off, the PCTRL terminal voltage is 0.86 V or higher for 5 seconds or more.
- C1457The PCTRL terminal voltage is below 0.3 V for 5 seconds.
- C1458One of the following condition is met: · When the vehicle speed is 10 km/h (6 mph) or more, noise occurs in...
- U0073One of the following conditions is met: · When the IG1 terminal voltage is between 10 and 17.4 V, after the...
- U0073One of the following conditions is met: · When the IG1 terminal voltage is between 10 and 17.4 V, after the...
- U0100Either condition is met: · When the IG1 terminal voltage is between 10 and 17.4 V and the vehicle speed 15...
- U0100Either condition is met: · When the IG1 terminal voltage is between 10 and 17.4 V and the vehicle speed 15...
- U0114The CAN signal from the four wheel drive control ECU is lost or malfunctioning for 1.2 seconds.
- U0114The CAN signal from the four wheel drive control ECU is lost or malfunctioning for 1.2 seconds.
- U0123Either condition is met: · When the IG1 terminal voltage is between 10 and 17.4 V, data from the yaw rate...
- U0123Either condition is met: · When the IG1 terminal voltage is between 10 and 17.4 V, data from the yaw rate...
- U0124Either condition is met: · When the IG1 terminal voltage is between 10 and 17.4 V, data from the acceleration...
- U0124Either condition is met: · When the IG1 terminal voltage is between 10 and 17.4 V, data from the acceleration...
- U0126One of the following conditions is met: · When the IG1 terminal voltage is between 10 and 17.4 V, data from...
- U0126One of the following conditions is met: · When the IG1 terminal voltage is between 10 and 17.4 V, data from...
- C1231An abnormal steering angle signal is received.
- C1531A short or open in the solenoid valve circuit
- C1541An abnormal vehicle speed signal is received.
- C1544An abnormal engine speed signal is received.
- C1544An abnormal engine speed signal is received.
- C1547An abnormal vehicle speed signal is received.
- C15F0A short or open in the solenoid valve circuit.
- C15F1An abnormal steering angle signal is received.
- U0073Control module communication bus off.
- U0100The engine speed signal is lost.
- U0126The steering angle signal is lost.
- U0129The vehicle speed signal is lost.
- B1579Telephone microphone signal is lost.
- B1585USB Device Malfunction · Non mass-storage class or incompatible protocol USB device · USB device with an...
- B158DThe internal video signal of the radio receiver assembly is interrupted
- B158FAV Signal Stoppage (Low Battery Voltage)
- B15A0When either condition below is met: · Bus malfunction · EEPROM error
- B15B0Picture circuit (TFT unit) malfunction
- B15B3When one of the conditions below is met: · AM tuner PLL is unlocked · FM tuner PLL is unlocked · Tuner...
- B15B5When one of the conditions below is met: · Mechanism drive signal malfunction · Load/Eject malfunction · Read...
- B15B7"Bluetooth" module malfunction
- B15C3A short is detected in the speaker output circuit.
- U0073CAN bus connection error
- U0140CAN reception error
- B1206No communication between the multiplex network master switch assembly and main body ECU (multiplex network...
- B1273No communication between the sliding roof ECU (sliding roof drive gear sub-assembly) and main body ECU...
- B1273No communication between the sliding roof drive gear sub-assembly and main body ECU (multiplex network body...
- B1287No communication between the multiplex network door ECU (back door P/W) and main body ECU (multiplex network...
- B2321No communication between the front power window regulator motor assembly LH and main body ECU (multiplex...
- B2322No communication between the front power window regulator motor assembly RH and main body ECU (multiplex...
- B2323No communication between the rear power window regulator motor assembly RH and main body ECU (multiplex...
- B2324No communication between the rear power window regulator motor assembly LH and main body ECU (multiplex...
- B2325The main body ECU (multiplex network body ECU) detects a malfunction in the LIN communication bus between...
- B2325The main body ECU (multiplex network body ECU) detects a malfunction in the LIN communication bus between...
- B2327No communication between the multiplex network door ECU (back door P/W) and back door power window regulator...
- B2328The multiplex network door ECU (back door P/W) detects a malfunction in the LIN communication bus between the...
- U0208There is no communication from the front power seat switch LH.
- U1002Lost communication with the gateway module.
- B2780The unlock warning switch assembly is not detected as being on when the ignition switch is ON.
- B2784The antenna coil is open/shorted.
- B2793A transponder chip malfunction.
- B2794A key with an incomplete key code is inserted into the ignition key cylinder.
- B2795A key with an unregistered key code is inserted into the ignition key cylinder.
- B2796The key code cannot be transmitted.
- B27972 or more ignition keys are positioned too close to each other or noise occurs in the communication line.
- B2798Key code identification cannot be completed within the specified time.
- B2799One of the following conditions is met: · An error in communication between the ECM and transponder key ECU...
- B279AThe communication line (EFIO-IMI) between the ECM and transponder key ECU assembly is stuck on HI output for...
- B279CAn ECM for vehicles without an engine immobiliser system is installed to a vehicle with an engine immobiliser...
- B1500IG voltage is 9.5 V or higher and the following condition is met: 1. Fuel sender gauge operation malfunction.
- U0100IG voltage is 9.5 V or higher and the following condition is met: 1. No communication with the ECM continues...
- U0129IG voltage is 9.5 V or higher and the following condition is met: 1. No communication with the skid control...
- U0131IG voltage is 9.5 V or higher and the following condition is met: 1. No communication with the power steering...
- U0151IG voltage is 9.5 V or higher and the following condition is met: 1. No communication with the center airbag...
- B1000/31 A center airbag sensor malfunction.
- B1610/13 Either condition is met: · A front airbag sensor RH malfunction. · A center airbag sensor malfunction.
- B1612/83 One of the following conditions is met: · The center airbag sensor detects a line short circuit signal, open...
- B1613/83 One of the following conditions is met: · The center airbag sensor detects line short circuit signal, an open...
- B1615/14 Either condition is met: · A front airbag sensor LH malfunction. · A center airbag sensor malfunction.
- B1617/84 One of the following conditions is met: · The center airbag sensor detects a line short circuit signal, open...
- B1618/84 One of the following conditions is met: · The center airbag sensor detects a line short circuit signal, open...
- B161A/8A In order to check the operation of the passenger airbag ON/OFF indicator when approximately 6 seconds have...
- B1630/23 Either condition is met: · A rear airbag sensor RH malfunction. · A center airbag sensor malfunction.
- B1633/81 One of the following conditions is met: · The center airbag sensor detects a line short circuit signal, open...
- B1635/24 Either condition is met: · A rear airbag sensor LH malfunction. · A center airbag sensor malfunction.
- B1638/82 One of the following conditions is met: · The center airbag sensor detects a line short circuit signal, open...
- B1642/81 One of the following conditions is met: · The center airbag sensor detects a line short circuit signal, open...
- B1647/82 One of the following conditions is met: · The center airbag sensor detects a line short circuit signal, open...
- B1656/38 One of the following conditions is met: · The center airbag sensor detects a line short circuit signal, open...
- B1675/82 Either condition is met: · A rear floor side airbag sensor malfunction. · A center airbag sensor malfunction.
- B1676/85 One of the following conditions is met: · The center airbag sensor detects a line short circuit signal, open...
- B1677/85 One of the following conditions is met: · The center airbag sensor detects a line short circuit signal, open...
- B1690/15 Either condition is met: · A side airbag sensor RH malfunction. · A center airbag sensor malfunction.
- B1692/81 One of the following conditions is met: · The center airbag sensor detects a line short circuit signal, open...
- B1693/81 One of the following conditions is met: · The center airbag sensor detects a line short circuit signal, open...
- B1695/16 Either condition is met: · A side airbag sensor LH malfunction. · A center airbag sensor malfunction.
- B1697/82 One of the following conditions is met: · The center airbag sensor detects a line short circuit signal, open...
- B1698/82 One of the following conditions is met: · The center airbag sensor detects a line short circuit signal, open...
- B1800/51 One of the following conditions is met: · The center airbag sensor detects a line short circuit signal 5...
- B1801/51 One of the following conditions is met: · The center airbag sensor detects an open circuit signal in the...
- B1802/51 One of the following conditions is met: · The center airbag sensor detects a short circuit to ground signal...
- B1803/51 One of the following conditions is met: · The center airbag sensor detects a short circuit to B+ signal in...
- B1805/52 One of the following conditions is met: · The center airbag sensor detects a line short circuit signal 5...
- B1806/52 One of the following conditions is met: · The center airbag sensor detects an open circuit signal in the...
- B1807/52 One of the following conditions is met: · The center airbag sensor detects a short circuit to ground signal...
- B1808/52 One of the following conditions is met: · The center airbag sensor detects a short circuit to B+ signal in...
- B1810/53 One of the following conditions is met: · The center airbag sensor detects a line short circuit signal 5...
- B1811/53 One of the following conditions is met: · The center airbag sensor detects an open circuit signal in the...
- B1812/53 One of the following conditions is met: · The center airbag sensor detects a short circuit to ground signal...
- B1813/53 One of the following conditions is met: · The center airbag sensor detects a short circuit to B+ signal in...
- B1815/54 One of the following conditions is met: · The center airbag sensor detects a line short circuit signal 5...
- B1816/54 One of the following conditions is met: · The center airbag sensor detects an open circuit signal in the...
- B1817/54 One of the following conditions is met: · The center airbag sensor detects a short circuit to ground signal...
- B1818/54 One of the following conditions is met: · The center airbag sensor detects a short circuit to B+ signal in...
- B1820/55 One of the following conditions is met: · The center airbag sensor detects a line short circuit signal 5...
- B1821/55 One of the following conditions is met: · The center airbag sensor detects an open circuit signal in the side...
- B1822/55 One of the following conditions is met: · The center airbag sensor detects a short circuit to ground signal...
- B1823/55 One of the following conditions is met: · The center airbag sensor detects a short circuit to B+ signal in...
- B1825/56 One of the following conditions is met: · The center airbag sensor detects a line short circuit signal 5...
- B1826/56 One of the following conditions is met: · The center airbag sensor detects an open circuit signal in the side...
- B1827/56 One of the following conditions is met: · The center airbag sensor detects a short circuit to ground signal...
- B1828/56 One of the following conditions is met: · The center airbag sensor detects a short circuit to B+ signal in...
- B1830/57 One of the following conditions is met: · The center airbag sensor detects a line short circuit signal 5...
- B1831/57 One of the following conditions is met: · The center airbag sensor detects an open circuit signal in the...
- B1832/57 One of the following conditions is met: · The center airbag sensor detects a short circuit to ground signal...
- B1833/57 One of the following conditions is met: · The center airbag sensor detects a short circuit to B+ signal in...
- B1835/58 One of the following conditions is met: · The center airbag sensor detects a line short circuit signal 5...
- B1836/58 One of the following conditions is met: · The center airbag sensor detects an open circuit signal in the...
- B1837/58 One of the following conditions is met: · The center airbag sensor detects a short circuit to ground signal...
- B1838/58 One of the following conditions is met: · The center airbag sensor detects a short circuit to B+ signal in...
- B1900/73 One of the following conditions is met: · The center airbag sensor detects a line short circuit signal 5...
- B1901/73 One of the following conditions is met: · The center airbag sensor detects an open circuit signal in the...
- B1902/73 One of the following conditions is met: · The center airbag sensor detects a short circuit to ground signal...
- B1903/73 One of the following conditions is met: · The center airbag sensor detects a short circuit to B+ signal in...
- B1905/74 One of the following conditions is met: · The center airbag sensor detects a line short circuit signal 5...
- B1906/74 One of the following conditions is met: · The center airbag sensor detects an open circuit signal in the...
- B1907/74 One of the following conditions is met: · The center airbag sensor detects a short circuit to ground signal...
- B1908/74 One of the following conditions is met: · The center airbag sensor detects a short circuit to B+ signal in...
- B2650The forward and backward lock detection position of the sensor is the same.
- B2651The forward and backward lock detection position of the sensor is the same.
- B2652The upward and downward lock detection position of the sensor is the same.
- B2653The upward and downward lock detection position of the sensor is the same.
- B2658A problem with the voltage supplied to the position control sensor.
- B1411/11 An open or short in the cooler thermistor (room temperature sensor) circuit.
- B1412An open or short in the cooler thermistor (ambient temperature sensor) circuit.
- B1412/12 An open or short in the cooler thermistor (ambient temperature sensor) circuit.
- B1413An open or short in the No. 1 cooler thermistor circuit.
- B1413/13 An open or short in the No. 1 cooler thermistor circuit.
- B1422Open or short in the compressor lock sensor circuit.
- B1422/22 Open or short in the compressor lock sensor circuit.
- B1441The air mix damper position does not change when the air conditioning amplifier assembly operates the damper...
- B1441/41 The air mix damper position does not change when the air conditioning amplifier assembly operates the damper...
- B1442The air inlet damper position does not change when the air conditioning amplifier assembly operates the...
- B1442/42 The air inlet damper position does not change when the air conditioning amplifier assembly operates the...
- B1443The air outlet damper position does not change when the air conditioning amplifier assembly operates the...
- B1443/43 The air outlet damper position does not change when the air conditioning amplifier assembly operates the...
- B1443/43 The air outlet damper position does not change when the air conditioning amplifier assembly operates the...
- B1446/46 The air mix damper position does not change when the air conditioning amplifier assembly operates the damper...
- B1497An open circuit or malfunction in the communication line.
- B1497/97 An open circuit or malfunction in the communication line.
- B14A2An open or short in the driver side solar sensor circuit.
- B14A3An open or short in the passenger side solar sensor circuit.
- U0100Lost communication with the ECM.
- U0100Lost communication with the ECM.
- U0142Lost communication with the main body ECU.
- U0142Lost communication with the main body ECU.
- U0155Lost communication with the combination meter.
- U0155Lost communication with the combination meter.
- B2311Either condition is met: 1. Back door power window regulator motor malfunctions. 2. ECU in the back door...
- B2311Either condition is met: 1. Power window regulator motor assembly malfunctions. 2. ECU in the power window...
- B2311Either condition is met: 1. Power window regulator motor assembly malfunctions. 2. ECU in the power window...
- B2312Either condition is met: · The multiplex network master switch is stuck. · The multiplex network master...
- B2312The back door power window regulator motor is stuck.
- B2313Either condition is met: · Power window regulator motor is not initialized. · Power window regulator motor...
- B2313Either condition is met: · Power window regulator motor is not initialized. · Power window regulator motor...
- B2341There is a sensor (motor) failure.
- B2342The sliding roof drive gear sub-assembly detects that the sliding roof switch in the map light assembly is...
- B2342The sliding roof drive gear sub-assembly detects that the sliding roof switch in the map light assembly is...
- B2343The sliding roof drive gear sub-assembly has not been initialized.
- B2343The sliding roof drive gear sub-assembly has not been initialized.
- B2344There is a position failure.
Common jobs · 1GR-FE (12)
- Read / clear codes
- Drive belt: on-vehicle inspection · removal · installation
- Water pump: on-vehicle inspection
- Thermostat: inspection
- Radiator: on-vehicle inspection
- Fuel pump: inspection · disassembly · reassembly
- Fuel filter: replacement
- Injectors: inspection
- Throttle body: on-vehicle inspection · inspection
- Cylinder head: inspection · replacement · disassembly · reassembly
- Engine assembly: on-vehicle inspection · inspection
- Starter: inspection · removal · disassembly · reassembly · installation
Common jobs · chassis & body (9)
- Alternator: inspection · removal · disassembly · reassembly · installation
- ATF: adjustment
- Front brakes: inspection · removal · disassembly · reassembly
- Rear brakes: inspection · removal · disassembly · reassembly · installation
- Brake fluid: on-vehicle inspection · replacement · bleeding
- Parking brake: inspection · disassembly · reassembly
- Wheel alignment: adjustment
- Front drive shaft: inspection · removal · disassembly · reassembly · installation
- A/C refrigerant: on-vehicle inspection · replacement
Repair Manual
General295 documents
Engine / Hybrid System445 documents
Drivetrain320 documents
Suspension54 documents
Brake260 documents
Steering68 documents
Audio / Visual / Telematics262 documents
Power Source / Network78 documents
Vehicle Interior745 documents
Vehicle Exterior525 documents
New Car Features
General11 documents
Engine / Hybrid System47 documents
Drivetrain19 documents
Suspension6 documents
Brake17 documents
Steering7 documents
Audio / Visual / Telematics27 documents
Power Source / Network13 documents
Vehicle Interior66 documents
Vehicle Exterior30 documents