Home › Vehicle Exterior › BODY WELD POINT › FIT STANDARD / ADJUSTMENT METHOD
BM1440E _01 Vehicle Exterior _056782 BODY WELD POINT _0276967 FIT STANDARD / ADJUSTMENT METHOD F

BODY WELD POINT  FIT STANDARD / ADJUSTMENT METHOD  ADJUSTMENT  


INSPECT HOOD SUB-ASSEMBLY


a.

Check that the clearance measurements of areas A through E are within each standard range.

B237120E02
1.927,0.323 2.156,0.521 0.229,0.198 10 false A 3.771,0.354 4,0.552 0.229,0.198 10 false B 4.125,1.198 4.354,1.396 0.229,0.198 10 false C 5.292,0.49 5.521,0.688 0.229,0.198 10 false D 6.094,1 6.323,1.198 0.229,0.198 10 false E

Standard:
Area Measurement Area Measurement
A 3.65 to 7.65 mm (0.144 to 0.301 in.) B 5.15 to 9.15 mm (0.203 to 0.360 in.)
C 4.05 to 8.05 mm (0.165 to 0.323 in.) D 2.0 to 5.0 mm (0.0787 to 0.197 in.)
E -1.5 to 1.5 mm (-0.0591 to 0.0591 in.) - -


HINT:

Centering bolts are used to mount the hood hinge and hood lock. The hood and hood lock cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.




ADJUST HOOD SUB-ASSEMBLY


a.

Adjust the hood position.

i.
B237105

Loosen the 4 hinge bolts on the hood.


ii.

Move the hood and adjust the clearance between the hood and front fender.


iii.

Tighten the 4 hinge bolts on the hood after the adjustment.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)



b.

Adjust the height of the front end of the hood using the cushion rubbers.

i.
B237106

Adjust the cushion rubbers so that the hood and fender are aligned.

HINT:

Raise or lower the front end of the hood by turning the 2 cushion rubbers.




c.

Adjust the hood lock.

i.
B237107

Loosen the 3 bolts.


ii.

Adjust the hood lock and tighten the 3 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


iii.

Check that the striker can engage with the hood lock smoothly.




INSPECT FRONT DOOR


a.

Check that the clearance measurements of areas A through H are within each standard range.

B237121E02
1.958,0.813 2.146,1.042 0.188,0.229 10 false A 3.917,0.573 4.188,0.802 0.271,0.229 10 false B 5.125,0.406 5.396,0.635 0.271,0.229 10 false C 5.698,2.094 5.969,2.323 0.271,0.229 10 false D 6.365,2.198 6.635,2.427 0.271,0.229 10 false E 4.875,3.802 5.146,4.031 0.271,0.229 10 false F 1.229,3.406 1.5,3.635 0.271,0.229 10 false G 2.042,3.531 2.313,3.76 0.271,0.229 10 false H

Standard:
Area Measurement Area Measurement
A 3.8 to 6.8 mm (0.150 to 0.268 in.) B 3.9 to 6.9 mm (0.154 to 0.272 in.)
C 3.4 to 6.4 mm (0.134 to 0.252 in.) D 3.0 to 6.0 mm (0.118 to 0.236 in.)
E -1.5 to 1.5 mm (-0.0591 to 0.0591 in.) F 4.05 to 7.05 mm (0.159 to 0.278 in.)
G 2.7 to 5.7 mm (0.106 to 0.224 in.) H -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)


HINT:

Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts installed on it. Substitute the centering bolts with standard bolts when making adjustments.




ADJUST FRONT DOOR


a.
B237122

Using SST, loosen the hinge bolts on the vehicle body and adjust the door position.

SST
09812-00010  


b.

Tighten the hinge bolts on the vehicle body after the adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


c.

Loosen the hinge bolts on the door and adjust the door position.


d.

Tighten the hinge bolts on the door after the adjustment.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)


e.
B237123

Using a T40 "TORX" socket wrench, slightly loosen the striker mounting screws.


f.

Using a brass bar and hammer, hit the striker to adjust its position.


g.

Using a T40 "TORX" socket wrench, tighten the striker mounting screws after the adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)



INSPECT REAR DOOR


a.

Check that the clearance measurements of areas A through H are within each standard range.

B237263E02
5.271,0.448 5.51,0.667 0.24,0.219 10 false A 6.063,2.542 6.302,2.76 0.24,0.219 10 false C 3.531,3.531 3.771,3.75 0.24,0.219 10 false D 1.917,2.406 2.156,2.625 0.24,0.219 10 false E 1.031,2.458 1.271,2.677 0.24,0.219 10 false F 1.875,0.875 2.115,1.094 0.24,0.219 10 false G 4.219,0.417 4.458,0.635 0.24,0.219 10 false H 5.427,1.969 5.667,2.188 0.24,0.219 10 false B

Standard:
Area Measurement Area Measurement
A 3.6 to 6.6 mm (0.142 to 0.260 in.) B 2.7 to 5.7 mm (0.106 to 0.224 in.)
C -1.5 to 1.5 mm (-0.0591 to 0.0591 in.) D 5.35 to 8.35 mm (0.211 to 0.335 in.)
E 3.0 to 6.0 mm (0.118 to 0.236 in.) F -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
G 3.4 to 6.4 mm (0.134 to 0.252 in.) H 3.9 to 6.9 mm (0.154 to 0.272 in.)


HINT:

Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.




ADJUST REAR DOOR


a.
B237264

Using SST, loosen the hinge bolts on the vehicle body and adjust the door position.

SST
09812-00010  


b.

Tighten the hinge bolts on the vehicle body after the adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


c.

Loosen the hinge bolts on the door and adjust the door position.


d.

Tighten the hinge bolts on the door after the adjustment.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)


e.
B217848

Using a T40 "TORX" socket wrench, slightly loosen the striker mounting screws.


f.

Using a brass bar and hammer, hit the striker to adjust its position.


g.

Using a T40 "TORX" socket wrench, tighten the striker mounting screws after the adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)



INSPECT BACK DOOR


a.

Check that the clearance measurements of areas A through G are within each standard range.

B237265E01
2.977,0.265 3.217,0.476 0.241,0.211 10 A 3.272,0.488 3.513,0.699 0.241,0.211 10 B 5.818,0.644 6.059,0.855 0.241,0.211 10 C 6.119,2.146 6.360,2.357 0.241,0.211 10 D 1.415,2.036 1.655,2.247 0.241,0.211 10 E 1.345,3.537 1.586,3.748 0.241,0.211 10 F 3.822,3.751 4.062,3.962 0.241,0.211 10 G

Standard:
Area Measurement Area Measurement
A 9.2 to 12.2 mm (0.362 to 0.480 in.) B 0.0 to 3.0 mm (0.0 to 0.118 in.)
C 3.0 to 6.0 mm (0.118 to 0.236 in.) D 3.7 to 6.7 mm (0.146 to 0.264 in.)
E 6.25 to 9.25 mm (0.246 to 0.364 in.) F 6.55 to 9.55 mm (0.258 to 0.376 in.)
G 8.45 to 11.45 mm (0.333 to 0.451 in.) - -


HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.

·

Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts and washers when making adjustments.





ADJUST BACK DOOR


a.
B237266

Before adjusting the upper end of the back door up and down or left and right, loosen the bolts.


b.

Tighten the body side hinge after the adjustment.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


c.
B237267

Using a T40 "TORX" socket wrench, slightly loosen the striker mounting screws.


d.

Using a brass bar and hammer, hit the striker to adjust its position.


e.

Using a T40 "TORX" socket wrench, tighten the striker mounting screws after the adjustment.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)