Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › from 2014.08
NM1440E _51 Engine / Hybrid System _056078 1GR-FE ENGINE CONTROL _0273696 SFI SYSTEM UN GENERAL/CONTROL/DETAILS F

1GR-FE ENGINE CONTROL  SFI SYSTEM  GENERAL/CONTROL/DETAILS  DETAILS  


FUNCTION OF MAIN COMPONENTS


a.

The main components of the engine control system are as follows:

Component Outline Quantity Function
ECM 32-bit CPU 1 The ECM optimally controls the SFI, ESA and ISC to suit the operating conditions of the engine in accordance with the signals provided by the sensors.
Intake Mass Air Flow Meter Sub-assembly Hot-wire Type 1 This sensor has a built-in hot-wire to directly detect the intake air mass.
Intake Air Temperature Sensor Thermistor Type 1 This sensor detects the intake air temperature by means of an internal thermistor.
E.F.I. Engine Coolant Temperature Sensor Thermistor Type 1 This sensor detects the engine coolant temperature by means of an internal thermistor.
Crank Position Sensor (Rotor Teeth) Pick-up Coil Type [36 - 2] 1 This sensor detects the engine speed and performs cylinder identification.
Camshaft Position Sensor (Intake) (No. 2 Crank Position Sensor) (Rotor Teeth) Magnetic Resistance Element (MRE) Type [3] 2 (1 each bank) This sensor performs cylinder identification.
Camshaft Position Sensor (Exhaust) (No. 2 Crank Position Sensor) (Rotor Teeth) Magnetic Resistance Element (MRE) Type [3] 2 (1 each bank) This sensor performs cylinder identification.
Accelerator Pedal Sensor Assembly Linear (Non-contact) Type 1 This sensor detects the amount of pedal effort applied to the accelerator pedal.
Throttle Position Sensor Linear (Non-contact) Type 1 This sensor detects the throttle valve opening angle.
Knock Control Sensor (Bank 1 and Bank 2) Built-in Piezoelectric Type (Non-resonant Type/ Flat Type) 2 (1 each bank) This sensor detects an occurrence of engine knocking indirectly from the vibration of the cylinder block sub-assembly caused by the occurrence of engine knocking.
Air Fuel Ratio Sensor (Bank 1, Sensor 1) (Bank 2, Sensor 1) Heated Type (Planar Type) 2 (1 each bank) As with the oxygen sensor, this sensor detects the oxygen concentration in the exhaust emission. However, it detects the oxygen concentration in the exhaust emission linearly.
Heated Oxygen Sensor (Bank 1, Sensor 2) (Bank 2, Sensor 2) Heated Type (Cup Type) 2 (1 each bank) This sensor detects the oxygen concentration in the exhaust emission by measuring the electromotive force which is generated in the sensor itself.
Fuel Injector Assembly 12-hole Type 6 The injector is an electromagnetically-operated nozzle which injects fuel in accordance with signals from the ECM.
Emission Control Valve Set*1 Solenoid Valve 2 To ensure the proper warm-up performance of the Three-Way Catalytic converters (TWCs) after starting a cold engine, an air injection system is used.
Air Injection Control Driver*2 Solenoid Valve 1
Air Pump Assembly*2 DC Type Pump Motor 1

*1: Models with Onboard Refueling Vapor Recovery (ORVR) Function

*2: Models with Air Injection Control System




SYSTEM CONTROL


a.

The engine control system of the 1GR-FE engine has the following features. The ECM that controls this system is made by DENSO.

System Outline
Sequential Multiport Fuel Injection (SFI) An L-type SFI system directly detects the intake air volume with a hot-wire type intake mass air flow meter sub-assembly.
Electronic Spark Advance (ESA)
·

Ignition timing is determined by the ECM based on signals from various sensors. The ECM corrects ignition timing in response to engine knocking.

·

This system selects the optimal ignition timing in accordance with the signals received from the sensors and sends (IGT) ignition signals to the igniters.


Electronic Throttle Control System-ligent (ETCS-i) Optimally controls the opening angle of the throttle valve in accordance with the accelerator pedal input and the engine and vehicle conditions.
Dual Variable Valve Timing-intelligent (Dual VVT-i) Controls the intake and exhaust camshaft to an optimal valve timing in accordance with engine operating conditions.
Fuel Pump Control Fuel pump operation is controlled by signals from the ECM. The fuel pump is stopped when the SRS airbags deploy.
Air Injection Control* This system uses an electric air pump assembly for pumping air to the cylinder head. This ensures the proper warm-up performance of the TWC during cooled down engine state.
Air Conditioning Cut-off Control By turning the air conditioning compressor ON or OFF in accordance with the engine conditions, drivability is maintained.
Air Fuel Ratio Sensor and Heated Oxygen Sensor Heater Control Maintains the temperature of the air fuel ratio sensors or heated oxygen sensors at an appropriate level to increase the ability of the sensor to accurately detect oxygen concentration.
Engine Immobilizer Prohibits fuel delivery and ignition if an attempt is made to start the engine with an invalid key.
Diagnosis When the ECM detects a malfunction, the ECM records the malfunction and information that relates to the fault.
Fail-safe When the ECM detects a malfunction, the ECM stops or controls the engine according to the data already stored in the memory.
Brake Override System The driving torque is restricted when the brake pedals is depressed while accelerator pedal is depressed. (For the Activation Conditions and Inspection Method, refer to the Repair Manual)

*: Models with Air Injection Control System




FUNCTION


a.

Dual VVT-i System

i.

The Dual Variable Valve Timing-intelligent (Dual VVT-i) system is designed to control the intake and exhaust camshaft within a range of 40° and 35° respectively (of Crankshaft Angle) to provide valve timing that is optimally suited to the engine operating conditions. This improves torque in all the speed ranges as well as increasing fuel economy, and reducing exhaust emissions.

W124666E02
3.813,0.063 3.99,0.229 0.177,0.167 10 false *1 3.813,0.302 4.01,0.448 0.198,0.146 9 false *2 3.813,0.542 4.01,0.688 0.198,0.146 9 false *3 3.813,0.771 4.01,0.917 0.198,0.146 9 false *4 3.813,1.042 4.01,1.188 0.198,0.146 9 false *5 3.813,1.302 4.01,1.448 0.198,0.146 9 false *6 3.813,1.833 4.01,1.979 0.198,0.146 9 false *7 3.813,2.177 4.01,2.323 0.198,0.146 9 false *8 3.813,2.521 4.01,2.667 0.198,0.146 9 false *9 3.771,2.875 4.021,3.021 0.25,0.146 9 false *10 4.833,1.917 5.083,2.063 0.25,0.146 9 false *11 5.771,2.521 6.021,2.667 0.25,0.146 9 false *12

Text in Illustration
*1 Cam Timing Oil Control Valve Assembly RH (Exhaust) *2 Cam Timing Oil Control Valve Assembly RH (Intake)
*3 Camshaft Position Sensor (No. 2 Crank Position Sensor) (Exhaust, RH) *4 E.F.I. Engine Coolant Temperature Sensor
*5 Cam Timing Oil Control Valve Assembly LH (Intake) *6 Camshaft Position Sensor (No. 2 Crank Position Sensor) (Exhaust, LH)
*7 Cam Timing Oil Control Valve Assembly LH (Exhaust) *8 Camshaft Position Sensor (No. 2 Crank Position Sensor) (Intake, LH)
*9 Crank Position Sensor *10 Camshaft Position Sensor (No. 2 Crank Position Sensor) (Intake, RH)
*11 ECM *12
·

Intake Mass Air Flow Meter Sub-assembly

·

Throttle Position Sensor




ii.

The VVT-i system delivers excellent benefits in the different operating conditions as shown in the table below.

Operation State Objective Effect
During Idling
W133869E01
1.594,0.281 2.052,0.479 0.458,0.198 10 false TDC 1.583,1.719 2.042,1.917 0.458,0.198 10 false BDC 0.969,1 1.219,1.219 0.25,0.219 10 false EX 2.365,1 2.615,1.198 0.25,0.198 10 false IN 0.573,0.167 1.5,0.688 0.927,0.521 9 false Earliest Timing (EX) 2.125,0.167 2.99,0.656 0.865,0.49 9 false Latest Timing (IN)

Eliminating overlap reduces blow back to the intake side.
·

Stabilized idling engine speed

·

Better fuel economy


At Light Load
W133870E01
1.594,0.271 1.906,0.479 0.313,0.208 10 false TDC 1.583,1.729 1.896,1.938 0.313,0.208 10 false BDC 0.927,1.021 1.24,1.229 0.313,0.208 10 false EX 2.354,1.021 2.667,1.229 0.313,0.208 10 false IN 0.49,0.24 1.406,0.594 0.917,0.354 9 false Earliest Timing (EX) 2.135,0.24 2.979,0.615 0.844,0.375 9 false Latest Timing (IN)

Eliminating overlap reduces blow back to the intake side. Engine stability is ensured
At Medium Load
W133871E02
1.563,0.271 1.906,0.458 0.344,0.188 10 false TDC 1.552,1.74 1.896,1.927 0.344,0.188 10 false BDC 0.927,1.031 1.208,1.229 0.281,0.198 10 false EX 2.344,1.031 2.688,1.219 0.344,0.188 10 false IN 0.688,0.229 1.354,0.667 0.667,0.438 9 false to Advance Side (IN) 2.125,0.24 2.698,0.688 0.573,0.448 9 false to Retard Side (EX)

Increasing overlap increases internal EGR, reducing pumping losses.
·

Better fuel economy

·

Improved emission control


In Low to Medium Speed Range with Heavy Load
W133872E02
1.563,0.26 1.896,0.458 0.333,0.198 10 false TDC 1.542,1.74 1.875,1.938 0.333,0.198 10 false BDC 0.958,0.969 1.292,1.167 0.333,0.198 10 false EX 2.323,0.969 2.656,1.167 0.333,0.198 10 false IN 0.667,1.406 1.24,1.792 0.573,0.385 9 false to Retard Side (EX) 2.188,1.406 2.844,1.813 0.656,0.406 9 false to Advance Side (IN)

Advancing the intake valve closing timing improves volumetric efficiency. Improved torque in low to medium speed range
In High Speed Range with Heavy Load
W133873E02
1.594,0.281 1.917,0.479 0.323,0.198 10 false TDC 1.573,1.75 1.896,1.948 0.323,0.198 10 false BDC 0.99,0.979 1.24,1.188 0.25,0.208 10 false EX 2.333,0.99 2.656,1.188 0.323,0.198 10 false IN 0.635,1.375 1.219,1.76 0.583,0.385 9 false to Retard Side (EX) 2.198,1.375 2.844,1.771 0.646,0.396 9 false to Advance Side (IN)

Retarding the intake valve closing timing improves volumetric efficiency. Improved output
At Low Temperatures
W133869E01
1.594,0.281 2.052,0.479 0.458,0.198 10 false TDC 1.583,1.719 2.042,1.917 0.458,0.198 10 false BDC 0.969,1 1.219,1.219 0.25,0.219 10 false EX 2.365,1 2.615,1.198 0.25,0.198 10 false IN 0.573,0.167 1.5,0.688 0.927,0.521 9 false Earliest Timing (EX) 2.125,0.167 2.99,0.656 0.865,0.49 9 false Latest Timing (IN)

Eliminating overlap to reduce blow back to the intake side stabilizes the idling speed at fast idle.
·

Stabilized fast idle engine speed

·

Better fuel economy


·

Starting the Engine

·

Stopping the Engine


W133869E01
1.594,0.281 2.052,0.479 0.458,0.198 10 false TDC 1.583,1.719 2.042,1.917 0.458,0.198 10 false BDC 0.969,1 1.219,1.219 0.25,0.219 10 false EX 2.365,1 2.615,1.198 0.25,0.198 10 false IN 0.573,0.167 1.5,0.688 0.927,0.521 9 false Earliest Timing (EX) 2.125,0.167 2.99,0.656 0.865,0.49 9 false Latest Timing (IN)

Eliminating overlap minimize blow back to the intake side. Improved startability



b.

Electronic Throttle Control System-intelligent (ETCS-i)

i.

The ETCS-i is used, providing excellent throttle control in all operating ranges. The accelerator cable has been discontinued, and an accelerator pedal position sensor has been provided on the accelerator pedal.


ii.

In the conventional throttle body with motor assembly, the throttle valve opening is determined invariably by the amount of accelerator pedal effort. In contrast, the ETCS-i uses the ECM to calculate the optimal throttle valve opening that is appropriate for the respective driving condition and uses a throttle control motor to control the opening.


iii.

The ETCS-i controls the Idle Speed Control (ISC) system, Traction Control (TRC) and Vehicle Stability Control (VSC) system.


iv.

In case of an abnormal condition, this system switches to the limp mode.

W124671E03
5.073,0.208 4.083,0.208 4.083,0.208 3.625,0.896 false 5.75,2.219 5.427,2.219 5.427,2.219 5.083,3 false 0.802,0.583 1.938,1.219 1.135,0.635 10 false Accelerator Pedal Sensor Assembly 0.75,2.792 2.073,3.417 1.323,0.625 10 false Intake Mass Air Flow Meter Sub-assembly 2.844,4.208 3.583,4.813 0.74,0.604 10 false Ignition Coil Assembly 4.229,4.198 5.021,4.885 0.792,0.688 10 false Fuel Injector Assembly 3.76,2.948 4.146,3.427 0.385,0.479 10 false ECM 5.573,2.896 6.729,3.198 1.156,0.302 10 false Skid Control ECU 5.813,2.125 6.906,2.51 1.094,0.385 10 false CAN (V Bus) 5.302,0.698 6.781,1.281 1.479,0.583 10 false Throttle Control Motor 5.115,0.104 6.354,0.563 1.24,0.458 10 false Throttle Valve 0.802,5.375 3.448,5.719 2.646,0.344 10 false : CAN Communication Line



c.

Fuel Pump Control

i.

The fuel pump is controlled by the ECM, using the fuel pump control ECU. The fuel pump control has a fuel cut control. Fuel cut control stops the fuel pump when any of the SRS airbags have deployed.




CONSTRUCTION


a.

Air Fuel Ratio Sensor and Heated Oxygen Sensor

i.

A planar type air fuel ratio sensor and a cup type heated oxygen sensor are used. The basic construction of the heated oxygen sensor and the air fuel ratio sensor is the same. However, they are divided into the cup type and the planar type, according to the different types of heater construction used.


ii.

The planar type air fuel ratio sensor uses alumina, which excels in heat conductivity and electrical insulation, to integrate a sensor element with a heater, thus improving the warm-up performance of the sensor.


iii.

The cup type heated oxygen sensor contains a sensor element that surrounds a heater.

W102072E06
2.479,2.042 2.594,1.219 2.594,1.219 2.698,1.219 true 2.75,2.052 2.927,1.646 2.927,1.646 3.021,1.646 true 2.646,2.438 2.948,2.354 2.948,2.354 3.021,2.354 true 2.594,2.635 2.906,2.927 2.906,2.927 3.01,2.927 true 2.552,2.802 2.865,3.417 2.865,3.417 3,3.417 true 2.49,2.438 1.885,3.094 1.885,3.094 1.615,3.094 true 2.427,2.698 1.969,3.365 1.969,3.365 1.625,3.365 true 6.104,1.948 6.302,1.542 6.302,1.542 6.542,1.542 true 6.208,1.948 6.396,1.719 6.396,1.719 6.563,1.719 true 5.969,1.938 6.25,1.375 6.25,1.375 6.563,1.375 true 5.792,1.938 5.792,1.375 5.792,1.375 5.313,1.375 true 5.688,1.938 5.688,1.375 true 0.458,0.292 0.802,0.646 0.344,0.354 12 false *A: 3.958,0.292 4.333,0.656 0.375,0.365 12 false *B: 1.438,2.99 1.635,3.156 0.198,0.167 10 false *1 1.438,3.26 1.646,3.448 0.208,0.188 10 false *6 3.031,3.313 3.229,3.469 0.198,0.156 10 false *2 2.74,1.115 2.938,1.271 0.198,0.156 10 false *5 3.073,1.542 3.271,1.698 0.198,0.156 10 false *4 3.052,2.25 3.25,2.406 0.198,0.156 10 false *3 3.052,2.823 3.25,2.979 0.198,0.156 10 false *1 6.594,1.438 6.792,1.635 0.198,0.198 10 false *3 6.594,1.271 6.792,1.469 0.198,0.198 10 false *4 5.146,1.271 5.344,1.448 0.198,0.177 10 false *1 6.594,1.615 6.792,1.802 0.198,0.188 10 false *2

Text in Illustration (Models without Onboard Refueling Vapor Recovery (ORVR) Function: )
*A Air Fuel Ratio Sensor (Planar Type) *B Heated Oxygen Sensor (Cup Type)
*1 Platinum Electrode *2 Sensor Element (Zirconia)
*3 Atmosphere *4 Heater
*5 Diffusion Resistance Layer *6 Alumina

W124927E02
2.76,2.094 2.979,1.802 2.979,1.802 3.094,1.802 false 2.615,2.448 2.802,1.573 2.802,1.573 2.906,1.573 false 2.438,2.104 2.26,1.615 2.26,1.615 2.146,1.615 true 2.75,2.094 2.969,1.802 2.969,1.802 3.083,1.802 true 2.615,2.458 2.802,1.583 2.802,1.583 2.906,1.583 true 2.583,2.646 2.969,2.938 2.969,2.938 3.052,2.938 true 2.51,3.188 2.677,3.51 2.677,3.51 2.771,3.51 true 2.458,2.729 2,3.177 2,3.177 1.906,3.177 true 2.365,3.073 2.177,3.479 2.177,3.479 2.073,3.479 true 5.833,1.979 6.042,1.302 6.042,1.302 6.135,1.302 true 6.021,1.927 6.125,1.563 6.125,1.563 6.198,1.563 true 5.948,2.927 6.292,3.323 6.292,3.323 6.448,3.323 true 5.802,2.958 5.667,3.521 5.667,3.521 5.521,3.521 true 5.625,2.813 5.417,3.271 5.417,3.271 5.25,3.271 true 0.427,0.146 0.781,0.365 0.354,0.219 12 false *A: 3.75,0.135 4.104,0.354 0.354,0.219 12 false *B: 1.958,1.51 2.198,1.688 0.24,0.177 10 false *1 2.948,1.479 3.188,1.656 0.24,0.177 10 false *2 3.135,1.698 3.375,1.875 0.24,0.177 10 false *3 3.094,2.833 3.333,3.01 0.24,0.177 10 false *4 5.083,3.167 5.323,3.344 0.24,0.177 10 false *4 6.49,3.219 6.729,3.396 0.24,0.177 10 false *4 2.813,3.406 3.052,3.583 0.24,0.177 10 false *6 5.344,3.417 5.583,3.594 0.24,0.177 10 false *6 1.906,3.375 2.146,3.552 0.24,0.177 10 false *5 1.74,3.073 1.979,3.25 0.24,0.177 10 false *4 6.167,1.198 6.406,1.375 0.24,0.177 10 false *3 6.25,1.458 6.49,1.635 0.24,0.177 10 false *2

Text in Illustration (Models with Onboard Refueling Vapor Recovery (ORVR) Function: )
*A Air Fuel Ratio Sensor (Planar Type) *B Heated Oxygen Sensor (Cup Type)
*1 Diffusion Resistance Layer *2 Atmosphere
*3 Heater *4 Platinum Electrode
*5 Alumina *6 Sensor Element (Zirconia)


iv.

As illustrated below, the conventional heated oxygen sensor is characterized by a sudden change in its output voltage at the threshold of the stoichiometric air fuel ratio (14.7:1). In contrast, the air fuel ratio sensor data is approximately proportionate to the existing air fuel ratio. The air fuel ratio sensor converts the oxygen density to current and sends it to the ECM. As a result, the detection precision of the air fuel ratio has been improved. The air fuel ratio sensor data can be viewed using GTS.

W132987E06
2.969,1.344 2.74,0.302 2.74,0.302 2.531,0.302 false 4.271,1.583 4.688,0.333 4.688,0.333 4.917,0.333 false 1.052,0.188 2.531,0.563 1.479,0.375 10 false Heated Oxygen Sensor 4.969,0.219 6.323,0.583 1.354,0.365 10 false Air Fuel Ratio Sensor 5.323,1.917 6.292,2.646 0.969,0.729 10 false Heated Oxygen Sensor Output 0.573,1.604 1.927,2.25 1.354,0.646 10 false Air Fuel Ratio Sensor Output* 0.594,2.344 1.792,3.021 1.198,0.677 10 false (Data Displayed on GTS) 1.646,3.385 1.917,3.677 0.271,0.292 10 false 2.2 1.625,0.948 1.917,1.24 0.292,0.292 10 false 4.2 5.083,0.833 5.354,1.156 0.271,0.323 10 false (V) 5.344,0.938 5.594,1.177 0.25,0.24 10 false 1 5.333,3.427 5.604,3.708 0.271,0.281 10 false 0.1 4.969,3.792 5.979,4.135 1.01,0.344 10 false 19 (Lean) 3.344,3.792 3.781,4.104 0.438,0.313 10 false 14.7 2.063,3.792 3.073,4.135 1.01,0.344 10 false 11 (Rich) 0.271,4.281 5.333,4.646 5.063,0.365 10 false *: This value is calculated internally in the ECM and is not an ECM terminal voltage. 5.823,3.698 6.813,4.094 0.99,0.396 10 false Air Fuel Ratio 1.833,0.823 2.104,1.146 0.271,0.323 10 false (V)



b.

Intake Mass Air Flow Meter Sub-assembly

i.

The intake mass air flow meter sub-assembly, which is a slot-in type, allows a portion of the intake air to flow through the detection area. By directly measuring the mass and the flow rate of the intake air, the detection precision is improved and the intake air resistance is reduced.


ii.

This intake mass air flow meter sub-assembly has a built-in intake air temperature sensor.

W124670E03
3.781,1.979 4.219,1.979 4.219,1.979 4.906,1.719 true 3.781,2.854 4.063,2.854 4.063,2.854 4.969,1.792 true 5.448,2.135 5.344,2.135 5.344,2.135 5.135,1.771 true 5.49,2.031 5.656,2.365 0.167,0.333 10 false *3 3.604,1.875 3.802,2.156 0.198,0.281 10 false *1 3.198,0.281 3.396,0.563 0.198,0.281 10 false *a 3.604,2.75 3.76,3.031 0.156,0.281 10 false *2 1.698,3.052 1.865,3.406 0.167,0.354 10 false A 1.698,0.469 1.854,0.74 0.156,0.271 10 false A

Text in Illustration
*1 Platinum Hot-wire Element *2 Temperature Sensing Element
*3 Intake Air Temperature Sensor - -
*a A - A Cross Section - -
V100135

Air Flow - -



c.

Crankshaft Position Sensor

i.

The timing rotor of the crankshaft consists of 34 teeth with 2 teeth missing. The crank position sensor outputs the crankshaft rotation signals every 10°, and the change of the signal due to the missing teeth is used to determine top-dead-center.

W102705E05
5.281,1.917 5.615,3.01 5.615,3.01 5.875,3.01 true 1.708,2.344 1.396,2.865 1.396,2.865 1.156,2.865 true 2.469,2 2.031,3.177 2.031,3.177 1.854,3.177 true 0.146,2.188 0.635,2.74 0.49,0.552 10 false Engine Front 0.323,2.75 1.156,3.01 0.833,0.26 10 false Timing Rotor 0.438,3.063 1.875,3.406 1.438,0.344 10 false Crank Position Sensor 3.875,0.948 6.802,1.396 2.927,0.448 10 false Crank Position Sensor Signal Plate (720°CA) 5.927,2.917 7.156,3.458 1.229,0.542 10 false 2 Teeth Missing 3.865,2.427 4.615,2.844 0.75,0.417 10 false 10°CA



d.

Camshaft Position Sensor

i.

Magnetic Resistance Element (MRE) type camshaft position sensors (No. 2 crank position sensor) are used. To detect each camshaft (intake) position, a timing rotor that is secured to the camshaft (intake) in front of the camshaft timing gear assembly is used to generate 6 (3 Hi Output, 3 Lo Output) pulses for every 2 revolutions of the crankshaft. The timing rotor for each camshaft (exhaust) is part of the respective camshaft.

W102073E03
4.344,0.677 4.729,0.677 4.729,0.677 5.177,1.021 true 1.167,2.958 1.563,2.958 1.563,2.958 2.021,2.302 true 3.354,2.927 2.896,2.927 2.896,2.927 2.563,2.51 true 6.063,3.073 5.646,3.073 5.646,3.073 5.031,2.229 true 4.167,0.573 4.344,0.76 0.177,0.188 10 false *1 0.99,2.854 1.167,3.042 0.177,0.188 10 false *2 6.083,2.969 6.26,3.156 0.177,0.188 10 false *2 3.385,2.823 3.563,3.01 0.177,0.188 10 false *3

Text in Illustration
*1 Camshaft Position Sensor (No. 2 Crank Position Sensor) (Exhaust, RH) *2 Timing Rotor
*3 Camshaft Position Sensor (No. 2 Crank Position Sensor) (Intake, RH) - -

W102098E03
0.146,0.125 2.198,0.531 2.052,0.406 12 false Sensor Output Waveforms: 2.969,0.885 5.99,1.188 3.021,0.302 10 false Camshaft Position Sensor Signal Plate (720°CA) 0.51,1.521 1.688,2.188 1.177,0.667 10 false Camshaft Position Sensor Signal 0.146,2.979 1.406,3.635 1.26,0.656 10 false Crankshaft Position Sensor Signal 3.031,2.698 3.552,2.896 0.521,0.198 10 false 360°CA 5.125,2.719 5.708,2.885 0.583,0.167 10 false 360°CA 2.271,4.25 2.729,4.417 0.458,0.167 10 false 10°CA 2.563,2.104 3.083,2.281 0.521,0.177 10 false 180°CA 5.115,2.104 5.635,2.281 0.521,0.177 10 false 120°CA 5.813,1.417 6.333,1.594 0.521,0.177 10 false 120°CA 4.24,1.417 4.76,1.594 0.521,0.177 10 false 180°CA 3.219,1.417 3.667,1.594 0.448,0.177 10 false 60°CA 3.583,2.313 4.031,2.49 0.448,0.177 10 false 60°CA 1.458,2.479 1.719,2.656 0.26,0.177 10 false 0 V 1.458,3.438 1.719,3.615 0.26,0.177 10 false 0 V


ii.

An MRE type camshaft position sensor (No. 2 crank position sensor) consists of an MRE, a magnet and a sensor. The direction of the magnetic field changes due to the profile (protruding and non-protruding portions) of the timing rotor, which passes by the sensor. As a result, the resistance of the MRE changes, and the output voltage to the ECM changes to Hi or Lo. The ECM detects the camshaft position based on this output voltage.

W100046E10
4.469,4.948 4.875,5.51 4.875,5.51 5.198,5.51 true 4.875,4.177 5.365,3.406 5.365,3.406 5.583,3.406 true 2.042,2.885 3.083,3.458 1.042,0.573 10 false MRE Type 5.094,2.885 6.188,3.313 1.094,0.427 10 false Pick-up Type 0.167,3.281 1.281,3.74 1.115,0.458 10 false Engine Speed 3.167,3.281 4.292,3.75 1.125,0.469 10 false Engine Speed 0.604,4.885 1.104,5.5 0.5,0.615 10 false Sensor Output 3.625,4.656 4.135,5.271 0.51,0.615 10 false Sensor Output 2.167,5.458 3.365,5.813 1.198,0.354 10 false Digital Output 6.156,5.156 7.156,5.552 1,0.396 10 false Analog Output 5.281,5.406 6.396,5.802 1.115,0.396 10 false No Detection 5.656,3.302 6.802,3.698 1.146,0.396 10 false No Detection 4.948,1.219 5.594,1.708 0.646,0.49 10 false ECM 1.74,1.542 3.385,2.469 1.646,0.927 10 false Camshaft Position Sensor (No. 2 Crank Position Sensor) (Intake, RH) 0.208,1.208 1.021,1.708 0.813,0.5 10 false Timing Rotor



e.

Knock Control Sensor (Flat Type)

i.

In a conventional knock control sensor (resonant type), a vibration plate is built into the sensor. This plate has the same resonance point as the knocking* frequency of the engine block. This sensor can only detect vibration in this frequency band.

*: The term "Knock" or "Knocking" is used in this case to describe either preignition or detonation of the air fuel mixture in the combustion chamber. This preignition or detonation refers to the air fuel mixture being ignited earlier than is advantageous. This use of "Knock" or "Knocking" is not primarily used to refer to a loud mechanical noise that may be produced by an engine.

A flat type knock control sensor (non-resonant type) has the ability to detect vibration in a wider frequency band (from about 5 kHz to 15 kHz). It has the following features:

·

A flat type knock control sensor is installed to an engine by placing it over the stud bolt installed on the cylinder block sub-assembly. For this reason, a hole for the stud bolt exists in the center of the sensor.

·

In the sensor, a steel weight is located in the upper portion. An insulator is located between the weight and a piezoelectric element.

·

An open/short circuit detection resistor is integrated in the sensor.



ii.

The engine knocking frequency will vary slightly depending on the engine speed. The flat type knock control sensor can detect vibration even when the engine knocking frequency changes. Due to the use of the flat type knock control sensor, the vibration detection ability is increased compared to a conventional type knock control sensor, and more precise ignition timing control is possible.

W100047E64
3.865,1.365 3.74,1.365 3.74,1.365 3.594,1.604 false 5.49,2.198 5.229,2.198 5.229,2.198 5.115,2.083 false 4,0.792 6.156,1.021 2.156,0.229 10 false Detection Band of Resonant Type 4,1.635 5.823,1.875 1.823,0.24 10 false Detection Band of Flat Type 3.104,2.385 3.885,2.573 0.781,0.188 10 false Frequency 1.167,1.281 1.708,1.531 0.542,0.25 10 false Voltage 1.563,0.375 1.802,0.563 0.24,0.188 10 false (V) 5.083,2.385 5.406,2.573 0.323,0.188 10 false (Hz) 3.906,1.24 4.094,1.427 0.188,0.188 10 false *1 5.521,2.073 5.708,2.26 0.188,0.188 10 false *2 0.229,2.969 4.135,3.177 3.906,0.208 10 false *1: Resonance Characteristic of Conventional Type (Resonant) 0.24,3.323 3.896,3.531 3.656,0.208 10 false *2: Resonance Characteristic of Flat Type (Non-resonant)


iii.

An open or short circuit detection resistor is integrated in the sensor. When the ignition is ON, the open or short circuit detection resistor in the knock control sensor and the resistor in the ECM keep the voltage at terminal KNK1 constant. An Integrated Circuit (IC) in the ECM constantly monitors the voltage of terminal KNK1. If an open or short circuit occurs between the knock control sensor and the ECM, the voltage of terminal KNK1 will change and the ECM will detect this and store a Diagnostic Trouble Code (DTC).

W102097E04
1.115,1.313 1.427,0.792 1.427,0.792 1.604,0.792 true 1.198,1.448 1.531,1.979 1.531,1.979 1.74,1.979 true 1.104,1.531 1.313,2.177 1.313,2.177 1.594,2.177 true 2.313,1.51 2.542,1.885 2.542,1.885 2.688,1.885 true 5.458,1.313 5.854,0.958 5.854,0.958 5.979,0.958 true 5.552,1.344 5.854,1.563 5.854,1.563 5.979,1.563 true 1.635,0.688 1.823,0.917 0.188,0.229 10 false *1 1.781,1.875 1.958,2.052 0.177,0.177 10 false *3 1.625,2.073 1.802,2.271 0.177,0.198 10 false *2 2.729,1.781 2.917,2.021 0.188,0.24 10 false *4 6.01,0.854 6.229,1.083 0.219,0.229 10 false *2 6,1.458 6.219,1.688 0.219,0.229 10 false *5 0.542,0.271 0.719,0.417 0.177,0.146 10 false *A 3.875,0.271 4.052,0.417 0.177,0.146 10 false *B

Text in Illustration
*A Flat Type (Non-Resonant Type) *B Conventional Type (Resonant Type)
*1 Steel Weight *2 Piezoelectric Element
*3 Insulator *4 Open Circuit Detection Resistor
*5 Vibration Plate - -

W102099E08
2.406,0.302 2.146,0.302 2.146,0.302 1.24,2.156 true 1.948,2.125 2.542,0.969 2.542,0.969 2.802,0.969 true 2.448,0.219 3.333,0.781 0.885,0.563 10 false Piezoelectric Element 2.854,0.865 4.021,1.583 1.167,0.719 10 false Open Circuit Detection Resistor 1.198,2.823 2.26,3.469 1.063,0.646 10 false Flat Type Knock Control Sensor 2.031,2.083 2.5,2.396 0.469,0.313 10 false 200 kΩ 3.781,1.917 4.177,2.229 0.396,0.313 10 false KNK1 3.771,2.552 4.198,2.865 0.427,0.313 10 false EKNK 5.031,2.823 5.385,3.156 0.354,0.333 10 false ECM 4.385,1.198 4.625,1.49 0.24,0.292 10 false 5 V 4.563,1.573 5.083,1.875 0.521,0.302 10 false 200 kΩ 6.073,1.979 6.229,2.271 0.156,0.292 10 false IC


iv.

Vibrations caused by knocking are transmitted to the steel weight. The inertia of this weight applies pressure to the piezoelectric element. This action generates electromotive force.

W100049E21
2.469,1.74 2.781,1.74 2.781,1.74 3.125,1.594 true 1.49,1.302 2.781,1.302 2.781,1.302 3.177,1.438 true 1.906,0.875 2.458,0.875 2.458,0.875 3.135,1.292 true 1.74,0.781 1.896,0.938 0.156,0.156 10 false *1 1.333,1.188 1.5,1.375 0.167,0.188 10 false *2 2.302,1.635 2.458,1.813 0.156,0.177 10 false *3

Text in Illustration
*1 Steel Weight *2 Inertia
*3 Piezoelectric Element - -


v.

These knock control sensors are mounted in the specific directions and angles as illustrated. To prevent the right and left bank connectors from being interchanged, make sure to install each sensor in its prescribed direction.

W102068E02
3.594,1.688 2.604,0.281 2.604,0.281 1.948,0.281 true 3.906,2.208 4.854,3.708 4.854,3.708 5.563,3.708 true 1.781,0.177 1.938,0.365 0.156,0.188 10 false *1 5.604,3.604 5.76,3.792 0.156,0.188 10 false *2

Text in Illustration
*1 Knock Control Sensor (KNK1) *2 Knock Control Sensor (KNK2)
V100135

Engine Front
V100136

Knock Control Sensor Mounting Direction



f.

Throttle Position Sensor

i.

This non-contact type throttle position sensor uses a Hall IC, which is mounted on the throttle body.

·

The Hall IC is surrounded by a magnetic yoke. The Hall IC converts the changes that occur in the magnetic flux into electrical signals, and outputs them in the form of throttle valve position signals to the ECM.

·

The Hall IC contains circuits for the main and sub signals. It converts the throttle valve opening angle into electric signals that have differing characteristics, and outputs them to the ECM.

W102100E03
5.583,0.719 5.406,0.719 5.406,0.719 5.125,1.76 true 5.583,1.063 5.448,1.063 5.448,1.063 5.125,1.927 true 5.573,2.948 5.427,2.948 5.427,2.948 5.125,2.125 true 5.615,2.844 5.781,3.021 0.167,0.177 10 false *1 5.615,0.615 5.781,0.781 0.167,0.167 10 false *1 5.615,0.958 5.781,1.135 0.167,0.177 10 false *2 3.5,0.521 3.677,0.698 0.177,0.177 10 false *a

Text in Illustration
*1 Magnet *2 Hall IC
*a Throttle Position Sensor - -

W102101E10
1.01,0.719 1.135,0.719 1.135,0.719 1.229,1.167 true 1.031,2.604 1.125,2.604 1.125,2.604 1.24,2.25 true 1.833,2.656 1.698,2.656 1.698,2.656 1.271,1.99 true 1.813,0.875 1.635,0.875 1.635,0.875 1.25,1.521 true 0.365,2.938 1.948,3.781 1.583,0.844 10 false Throttle Position Sensor 0.521,2.5 1.042,3 0.521,0.5 10 false Magnet 0.49,0.615 1.021,1.188 0.531,0.573 10 false Magnet 1.865,2.552 2.667,3.177 0.802,0.625 10 false Hall IC 1.854,0.771 2.594,1.385 0.74,0.615 10 false Hall IC 1.865,2.219 2.448,2.688 0.583,0.469 10 false VTA2 1.865,1.927 2.323,2.365 0.458,0.438 10 false VCTA 1.854,1.635 2.323,2.135 0.469,0.5 10 false ETA 1.854,1.344 2.448,1.917 0.594,0.573 10 false VTA1 2.573,1.667 3.167,2.208 0.594,0.542 10 false ECM 3.656,1.51 4.156,2.292 0.5,0.781 10 false Output Voltage 3.625,2.531 4.448,3.156 0.823,0.625 10 false Fully Closed 4,0.75 4.5,1.281 0.5,0.531 10 false (V) 4.052,0.958 4.427,1.49 0.375,0.531 10 false 5 4.5,1.135 5.125,1.615 0.625,0.479 10 false VTA2 5.385,1.688 6.021,2.135 0.635,0.448 10 false VTA1 4.698,2.656 6.104,3.479 1.406,0.823 10 false Throttle Valve Opening Angle 4.688,2.271 5.042,2.688 0.354,0.417 10 false 20 5.229,2.271 5.615,2.771 0.385,0.5 10 false 40 5.781,2.281 6.208,2.771 0.427,0.49 10 false 60 6.333,2.281 6.656,2.677 0.323,0.396 10 false 80 6.385,2.531 7.135,3.135 0.75,0.604 10 false Fully Open


HINT:

The inspection method differs from a contact type throttle position sensor because a non-contact type throttle position sensor uses a Hall IC. For details, refer to the Repair Manual.




g.

Accelerator Pedal Position Sensor

i.

This non-contact type accelerator pedal sensor assembly uses a Hall IC, which is mounted on the accelerator pedal arm.

·

A magnetic yoke is mounted at the base of the accelerator pedal arm. This yoke rotates around the Hall IC in accordance with the amount of effort that is applied to the accelerator pedal. The Hall IC converts the changes in the magnetic flux that occur into electrical signals, and outputs them in the form of accelerator pedal position signals to the ECM.

·

The Hall IC contains 2 circuits, one for the main signal, and one for the sub signal. It converts the accelerator pedal position (angle) into electric signals that have differing characteristics and outputs them to the ECM.

W110570E03
1.167,0.865 1.76,0.865 1.76,0.865 3.115,1.719 true 4.552,1.927 5.219,2.458 5.219,2.458 5.688,2.458 true 4.344,1.458 5.271,0.448 5.271,0.448 5.729,0.448 true 0.979,0.76 1.188,0.948 0.208,0.188 10 false *1 5.708,2.354 5.979,2.563 0.271,0.208 10 false *3 5.771,0.344 6.042,0.552 0.271,0.208 10 false *2

Text in Illustration
*1 Hall IC *2 Magnetic Yoke
*3 Accelerator Pedal Arm - -

W102103E07
0.604,1.188 0.729,1.188 0.729,1.188 1.406,1.542 true 0.573,2.271 0.688,2.271 0.688,2.271 1.417,1.938 true 1.198,2.625 1.271,2.625 1.271,2.625 1.448,2.25 true 1.24,0.781 1.313,0.781 1.313,0.781 1.417,1.156 true 4.219,2.458 6.583,3.167 2.365,0.708 10 false Accelerator Pedal Position (Angle) 6.427,2.271 7.156,2.813 0.729,0.542 10 false Fully Open 3.344,2.271 4.365,2.854 1.021,0.583 10 false Fully Closed 3.198,1.521 4.146,2.135 0.948,0.615 10 false Output Voltage 4.792,1.479 5.417,1.99 0.625,0.51 10 false VPA2 5.469,1.844 6.188,2.479 0.719,0.635 10 false VPA1 4.042,1.031 4.406,1.479 0.365,0.448 10 false 5 3.813,0.865 4.26,1.313 0.448,0.448 10 false (V) 2.583,1.573 3.24,2.208 0.656,0.635 10 false ECM 2.063,1.042 2.74,1.625 0.677,0.583 10 false VPA 2.073,1.333 2.698,1.927 0.625,0.594 10 false EPA 2.063,1.615 2.76,2.188 0.698,0.573 10 false VCPA 2.063,1.844 2.729,2.365 0.667,0.521 10 false VPA2 2.073,2.135 2.615,2.635 0.542,0.5 10 false EPA2 2.083,2.427 2.729,2.969 0.646,0.542 10 false VCP2 0.698,2.51 1.188,3.01 0.49,0.5 10 false Magnet 0.75,0.677 1.25,1.25 0.5,0.573 10 false Magnet 0.156,1.083 0.625,1.542 0.469,0.458 10 false Hall IC 0.115,2.156 0.563,2.646 0.448,0.49 10 false Hall IC 0.76,2.896 1.896,3.75 1.135,0.854 10 false Accelerator Pedal Sensor Assembly


HINT:

The inspection method differs from a contact type accelerator pedal position sensor because a non-contact type accelerator pedal position sensor uses a Hall IC. For details, refer to the Repair Manual.




h.

Cam Timing Oil Control Valve Assembly

i.

This cam timing oil control valve assembly controls the spool valve using duty-cycle control from the ECM. This allows hydraulic pressure to be applied to the camshaft timing gear assembly or camshaft timing exhaust gear assembly advance or retard side. When the engine is stopped, the cam timing oil control valve assembly (intake) will move to the retard position, and the cam timing oil control valve assembly (exhaust) will move to the advance position.

W102069E02
2.458,1.125 2.042,0.635 2.042,0.635 1.115,0.635 true 2.156,1.083 1.094,1.083 true 2.198,1.365 1.729,1.854 1.729,1.854 1.115,1.854 true 5.375,1.385 6.323,1.385 true 4.865,1.635 5.479,1.958 5.479,1.958 6.323,1.958 true 0.927,0.531 1.083,0.708 0.156,0.177 10 false *1 2.74,0.219 2.896,0.396 0.156,0.177 10 false *a 2.5,1.917 2.656,2.094 0.156,0.177 10 false *c 2.969,1.917 3.125,2.094 0.156,0.177 10 false *d 3.427,1.917 3.583,2.094 0.156,0.177 10 false *c 3.208,0.219 3.365,0.396 0.156,0.177 10 false *b 6.344,1.281 6.5,1.458 0.156,0.177 10 false *4 6.344,1.854 6.5,2.031 0.156,0.177 10 false *5 0.927,0.979 1.083,1.156 0.156,0.177 10 false *2 0.927,1.74 1.083,1.917 0.156,0.177 10 false *3

Text in Illustration (Intake Side: )
*1 Spool Valve *2 Sleeve
*3 Spring *4 Plunger
*5 Coil - -
*a to Camshaft Timing Gear Assembly (Advance Side) *b to Camshaft Timing Gear Assembly (Retard Side)
*c Drain *d Oil Pressure

W102093E02
2.458,1.385 2.042,0.896 2.042,0.896 1.115,0.896 true 2.167,1.302 1.104,1.302 true 2.198,1.594 1.729,2.094 1.729,2.094 1.115,2.094 true 5.375,1.615 6.323,1.615 true 4.854,1.875 5.469,2.208 5.469,2.208 6.313,2.208 true 0.927,0.792 1.083,0.969 0.156,0.177 10 false *1 2.74,0.458 2.896,0.635 0.156,0.177 10 false *a 2.5,2.177 2.656,2.354 0.156,0.177 10 false *c 2.969,2.177 3.125,2.354 0.156,0.177 10 false *d 3.427,2.177 3.583,2.354 0.156,0.177 10 false *c 3.208,0.458 3.365,0.635 0.156,0.177 10 false *b 6.344,1.51 6.5,1.688 0.156,0.177 10 false *4 6.344,2.104 6.5,2.281 0.156,0.177 10 false *5 0.927,1.198 1.083,1.375 0.156,0.177 10 false *2 0.927,1.99 1.083,2.167 0.156,0.177 10 false *3

Text in Illustration (Exhaust Side: )
*1 Spool Valve *2 Sleeve
*3 Spring *4 Plunger
*5 Coil - -
*a to Camshaft Timing Gear Assembly (Retard Side) *b to Camshaft Timing Gear Assembly (Advance Side)
*c Drain *d Oil Pressure



i.

Ignition Coil Assembly

i.

The Direct Ignition System (DIS) provides 6 ignition coil assemblies, one for each cylinder. The spark plug caps, which provide contact to the spark plugs, are integrated with the ignition coil assembly. Also, an igniter is enclosed to simplify the system.

U150608E02
3.365,0.979 3.385,1.01 0.021,0.031 3.49,2.927 3.583,2.927 false 3.49,2.938 3.583,2.938 false 3.677,2.927 3.583,2.927 false 3.677,2.938 3.583,2.938 false 3.219,0.917 3.188,0.969 false 3.854,0.979 3.594,0.979 3.594,0.979 3.583,1.01 false 3.385,0.99 3.396,0.99 false 3.385,1.01 3.396,1.01 false 3.344,0.99 3.365,0.99 false 3.344,1.01 3.365,1.01 false 3.802,1.01 3.802,1.021 false 3.844,1.01 3.844,1.021 false 3.521,1.01 3.521,1.021 false 3.74,1.063 3.74,1.063 3.74,1.063 3.719,1.042 false 3.656,1.125 3.677,1.125 false 3.656,1.104 3.677,1.104 false 3.719,1.01 3.719,1.021 false 3.698,1.01 3.698,1.021 false 3.604,1.01 3.604,1.021 false 3.469,1.146 3.469,2.125 3.469,2.125 3.479,2.25 false 3.458,2.333 3.479,2.333 false 3.344,1.052 3.438,1.052 false 3.385,1.188 3.354,1.188 3.354,1.188 3.354,1.198 false 3.583,2.781 3.542,2.781 3.542,2.781 3.542,2.802 false 3.583,2.76 3.542,2.76 3.542,2.76 3.542,2.781 false 3.583,3.323 3.51,3.323 false 3.51,0.99 3.583,0.99 false 3.583,1.073 3.51,1.073 false 3.073,0.802 3.063,0.781 false 3.01,0.927 2.979,0.927 false 3.49,1.094 3.51,1.094 false 3.49,1.125 3.51,1.125 false 3.479,2.594 3.49,2.594 false 3.479,2.625 3.49,2.625 false 3.521,2.823 3.583,2.823 false 3.76,1.167 3.76,2.448 3.76,2.448 3.771,2.448 false 3.708,1.115 3.708,1.125 false 3.698,1.146 3.698,2.125 3.698,2.125 3.677,2.25 false 3.708,2.333 3.677,2.333 false 3.771,1.188 3.802,1.188 3.802,1.188 3.802,1.198 false 3.583,2.781 3.625,2.781 3.625,2.781 3.625,2.802 false 3.583,2.76 3.615,2.76 3.615,2.76 3.615,2.781 false 3.583,3.323 3.646,3.323 false 3.583,1.073 3.646,1.073 false 3.677,2.594 3.667,2.594 false 3.677,2.625 3.667,2.625 false 3.646,2.823 3.583,2.823 false 3.854,1.156 3.854,1.198 false 3.823,1.156 3.823,1.198 false 3.51,3.063 3.646,3.063 false 4.01,0.99 4.01,0.875 false 4.125,0.99 4.125,0.875 false 4.01,0.99 4.01,1.115 false 4.125,0.99 4.125,1.115 false 3.5,3.052 3.656,3.052 false 2.51,1.729 2.823,1.729 2.823,1.729 3.583,1.865 true 4.615,1.906 4.177,1.906 4.177,1.906 3.688,1.656 true 4.615,2.385 4.229,2.385 4.229,2.385 3.75,2.167 true 2.521,3.51 2.823,3.51 2.823,3.51 3.469,3.26 true 4.615,0.635 4.302,0.635 4.302,0.635 3.771,0.969 true 4.656,0.531 4.802,0.708 0.146,0.177 10 false *1 4.656,1.802 4.802,1.979 0.146,0.177 10 false *3 4.656,2.281 4.802,2.458 0.146,0.177 10 false *4 2.333,1.625 2.479,1.802 0.146,0.177 10 false *2 2.333,3.406 2.479,3.583 0.146,0.177 10 false *5

Text in Illustration (Ignition Coil Assembly Cross Section: )
*1 Igniter *2 Iron Core
*3 Secondary Coil *4 Primary Coil
*5 Plug Cap - -



j.

Spark Plug

i.

Long-reach type spark plugs are used. This type of spark plug allows the area of the cylinder head sub-assembly that receives the spark plugs to be made thick. Thus, the water jacket can be extended near the combustion chamber, which contributes to cooling performance.


ii.

Iridium-tipped spark plugs are used to achieve a 120000 mile (192000 km) maintenance interval. By making the center electrode of iridium, it is possible to achieve superior ignition performance and durability when compared to platinum-tipped spark plugs.

W102071E03
2.823,1.281 1.625,0.781 1.625,0.781 1.365,0.781 true 3.563,1.417 4.49,1.052 4.49,1.052 5.156,1.052 true 1.635,3.333 2.24,3.333 true 1.635,3.458 2.24,3.458 true 4.375,4.344 4.542,4.51 0.167,0.167 10 false *A 5.5,4.344 5.667,4.51 0.167,0.167 10 false *B 1.167,0.677 1.344,0.833 0.177,0.156 10 false *1 5.188,0.948 5.365,1.104 0.177,0.156 10 false *1 2.271,3.229 2.448,3.385 0.177,0.156 10 false *2 2.271,3.354 2.448,3.51 0.177,0.156 10 false *3

Text in Illustration
*A Long-Reach Type *B Conventional Type
*1 Water Jacket *2 Iridium Tip
*3 Platinum Tip - -




OPERATION


a.

Dual VVT-i System

i.

Based on engine speed, intake air volume, throttle position and engine coolant temperature, the ECM calculates optimal valve timing for all driving conditions. The ECM also controls the cam timing oil control valve assemblies. In addition, the ECM uses signals from the camshaft position sensors (No. 2 crank position sensor) and the crank position sensor to detect the actual valve timing, thus providing feedback control to achieve the target valve timing.

W123735E02
0.354,0.302 1.719,0.917 1.365,0.615 10 false Intake Mass Air Flow Meter Sub-assembly 2.521,0.969 3.323,1.5 0.802,0.531 10 false Target Valve Timing 2.583,2.625 3.313,2.823 0.729,0.198 10 false Correction 2.5,5.198 3.323,5.875 0.823,0.677 10 false Actual Valve Timing 0.344,2.24 2.031,2.594 1.688,0.354 10 false Vehicle Speed Signal 0.333,2.729 1.708,3.323 1.375,0.594 10 false E.F.I. Engine Coolant Temperature Sensor 0.323,1.156 1.958,1.469 1.635,0.313 10 false Throttle Position Sensor 0.344,1.656 2.01,2.01 1.667,0.354 10 false Crank Position Sensor 0.333,3.479 1.979,4.323 1.646,0.844 10 false Camshaft Position Sensor (No. 2 Crank Position Sensor) (Intake, LH) 0.344,4.49 1.99,5.406 1.646,0.917 10 false Camshaft Position Sensor (No. 2 Crank Position Sensor) (Intake, RH) 0.344,5.583 1.99,6.531 1.646,0.948 10 false Camshaft Position Sensor (No. 2 Crank Position Sensor) (Exhaust, LH) 0.344,6.667 2,7.656 1.656,0.99 10 false Camshaft Position Sensor (No. 2 Crank Position Sensor) (Exhaust RH) 4.146,2.531 5.354,2.75 1.208,0.219 10 false Duty-cycle Control 4.313,0.917 5.521,1.135 1.208,0.219 10 false Duty-cycle Control 4.073,4.354 5.281,4.573 1.208,0.219 10 false Duty-cycle Control 3.948,6.083 5.156,6.302 1.208,0.219 10 false Duty-cycle Control 4.542,3.281 6.406,3.906 1.865,0.625 10 false Cam Timing Oil Control Valve Assembly RH (Intake) 4.521,1.5 6.365,2.135 1.844,0.635 10 false Cam Timing Oil Control Valve Assembly LH (Intake) 2.771,0.021 3.104,0.229 0.333,0.208 10 false ECM 2.948,3.177 3.729,3.344 0.781,0.167 10 false Feedback 4.51,5.031 6.365,5.646 1.854,0.615 10 false Cam Timing Oil Control Valve Assembly LH (Exhaust) 4.51,6.573 6.365,7.219 1.854,0.646 10 false Cam Timing Oil Control Valve Assembly RH (Exhaust)


ii.

When the cam timing oil control valve assembly is positioned as illustrated below by the advance signals from the ECM, the resultant oil pressure is applied to the timing advance side vane chamber to rotate the camshaft in the timing advance direction.

W102111E02
1.135,1.146 1.677,0.219 1.677,0.219 2.135,0.219 true 2.177,0.115 2.375,0.281 0.198,0.167 10 false *1 5.823,0.844 6.01,1.021 0.188,0.177 10 false *2

Text in Illustration (Advance Side Operation Intake Side: )
*1 Vane *2 ECM
V100135

Oil Flow
V100136

Rotation Direction

W102112E02
1.083,1 1.594,0.115 1.594,0.115 2.052,0.115 true 2.104,0 2.302,0.167 0.198,0.167 10 false *1 3.344,1.688 3.531,1.865 0.188,0.177 10 false *2

Text in Illustration (Advance Side Operation Exhaust Side: )
*1 Vane *2 ECM
V100135

Oil Flow
V100136

Rotation Direction


iii.

When the cam timing oil control valve assembly is positioned as illustrated below by the retard signals from the ECM, the resultant oil pressure is applied to the timing retard side vane chamber to rotate the camshaft in the timing retard direction.

W102113E02
1.125,1.948 1.354,2.667 1.354,2.667 1.938,2.667 true 1.99,2.563 2.156,2.729 0.167,0.167 10 false *1 5.938,0.885 6.125,1.063 0.188,0.177 10 false *2

Text in Illustration (Retard Side Operation Intake Side: )
*1 Vane *2 ECM
V100135

Oil Flow
V100136

Rotation Direction

W102114E02
1.135,2 1.354,2.729 1.354,2.729 1.938,2.729 true 1.99,2.625 2.156,2.792 0.167,0.167 10 false *1 3.344,1.688 3.531,1.865 0.188,0.177 10 false *2

Text in Illustration (Retard Side Operation Exhaust Side: )
*1 Vane *2 ECM
V100135

Oil Flow
V100136

Rotation Direction


iv.

After reaching the target timing, the engine valve timing is maintained by keeping the cam timing oil control valve assembly in the neutral position unless the engine operating conditions change.

This maintains the engine valve timing at the desired target position by preventing the engine oil from running out of the cam timing oil control valve assembly.



b.

Fuel Pump Control

i.

By adopting a linear type fuel pump control ECU with PWM (Pulse Width Modulation) control, the size and weight have been reduced and fuel economy has been improved due to lower electricity consumption.


ii.

The fuel pump control ECU receives 3-stage drive request signals (duty signals)*1 or linear signals (duty signals)*2 from the ECM and drives the fuel pump.


iii.

The fuel pump control is used to stop the fuel pump when the airbags deploy in a front or side collision.


iv.

In this system, when the airbag deployment signal from the center airbag sensor assembly is detected by the ECM, the ECM turns off the C/OPN relay*1 or EFI MAIN relay*2.


v.

After the fuel cut control has been activated, turning the power source from off to ON cancels the fuel cut control, and the engine can be restarted.

*1: Models without Onboard Refueling Vapor Recovery (ORVR) Function

*2: Models with Onboard Refueling Vapor Recovery (ORVR) Function


W124677E02
5.458,2.26 6.24,3.01 0.781,0.75 10 false Fuel Pump Control ECU 6.656,2.01 7.042,3.01 0.385,1 10 false Fuel Pump Motor 3.875,2.271 4.24,2.604 0.365,0.333 10 false ECM 2.906,2.479 3.76,2.896 0.854,0.417 10 false CAN (V Bus) 2.052,1.969 2.781,3.688 0.729,1.719 10 false Center Airbag Sensor Assembly 0.177,0.573 1.469,1.396 1.292,0.823 10 false Front Airbag Sensor (RH or LH) 0.188,2.01 1.417,2.854 1.229,0.844 10 false Side Airbag Sensor (RH or LH) 0.188,3.438 1.427,4.25 1.24,0.813 10 false Rear Airbag Sensor (RH or LH) 4.396,2.458 5.354,3.208 0.958,0.75 10 false Request Signal (Duty Signal) 6.073,0.802 7.052,1.781 0.979,0.979 10 false C/OPN Relay*1 or EFI MAIN Relay*2 0.646,5.385 3.292,5.729 2.646,0.344 10 false : CAN Communication Line 0.063,4.563 4.823,4.885 4.76,0.323 10 false *1: Models without Onboard Refueling Vapor Recovery (ORVR) Function 0.052,4.917 4.365,5.26 4.313,0.344 10 false *2: Models with Onboard Refueling Vapor Recovery (ORVR) Function



c.

Fuel Pump ECU

The fuel pump ECU controls fuel pump speed by receiving a duty cycle signal (FPC terminal input) from the ECM, control is performed to three stages. The fuel pump ECU also detects failures in the input and output circuits at the fuel pump ECU and transmits the failure status to the ECM*1.

W124749E02
5.844,1.24 6.646,1.656 0.802,0.417 9 false Fuel Pump 1.125,1.26 1.594,1.75 0.469,0.49 9 false ECM 4.542,1.365 5.281,2.167 0.74,0.802 9 false Fuel Pump Control ECU 2.083,0.896 4.094,1.26 2.01,0.365 9 false Fuel Pump Operation Request 2.5,2.542 3.844,3.021 1.344,0.479 9 false Diagnosis Signal 2.667,1.656 3.594,1.958 0.927,0.302 9 false Duty Signal 2,3.656 3.823,4.01 1.823,0.354 10 false Input Signal (Duty Signal) 4.885,4.354 5.167,4.646 0.281,0.292 10 false Hi 4.729,5.333 5.167,5.781 0.438,0.448 10 false Middle 4.802,6.427 5.104,6.813 0.302,0.385 10 false Low 4.792,7.281 5.115,7.615 0.323,0.333 10 false Stop 1.823,7.281 2.156,7.604 0.333,0.323 10 false GND 1.823,6.781 2.156,7.083 0.333,0.302 10 false GND 1.823,5.781 2.156,6.073 0.333,0.292 10 false GND 1.823,4.531 2.292,4.813 0.469,0.281 10 false GND 1.896,6.458 2.219,6.729 0.323,0.271 10 false +B 1.896,5.469 2.208,5.74 0.313,0.271 10 false +B 1.896,4.229 2.24,4.5 0.344,0.271 10 false +B 4.375,3.646 5.51,3.979 1.135,0.333 10 false Fuel Pump Speed 2.417,6.156 2.823,6.406 0.406,0.25 10 false 4.1ms 2.479,5.146 2.885,5.396 0.406,0.25 10 false 8.2ms 2.573,4.854 3.052,5.135 0.479,0.281 10 false 12.3ms 1.448,3.281 4.323,3.615 2.875,0.333 10 false - Fuel Pump Control Ecu Input - 0.042,0.063 5.844,0.396 5.802,0.333 12 false Models without Onboard Refueling Vapor Recovery (ORVR) Function:

In the fuel pump speed control, the ECM transmits fuel pump operation request signals in accordance with the engine operating conditions. In response to the request signals, the fuel pump ECU then transmits linear output signals to the fuel pump, optimally regulating the fuel pump speed.*2

In the fuel pump cut control, if the ECM receives airbag deployment signals from the center airbag sensor assembly, it transmits stop signals to the fuel pump ECU to bring the fuel pump to a halt. When receiving a stop signal, the fuel pump ECU stops the fuel pump*2.


Condition FP Terminal
Normal Duty input from the ECM: 25% to 80% Linear
Duty input from the ECM: 0% or 100%
(Included when the airbag is deployed.)
Off
Self-protection function is activated due to overcurrent or overheating. Off
Open circuit is detected in the FPC signal line connected to the ECM. Off



*1: Models without Onboard Refueling Vapor Recovery (ORVR) Function

*2: Models with Onboard Refueling Vapor Recovery (ORVR) Function