OUTLINE
The 1GR-FE engine is a 4.0 liter, 24 valve DOHC V6 engine. This engine uses a Dual Variable Valve Timing intelligent (Dual VVT-i) system, Direct Ignition System (DIS), and Electronic Throttle Control System intelligent (ETCS-i). These control functions achieve improved engine performance, fuel economy, and clean emissions.
SPECIFICATION
| Engine Type | 1GR-FE | ||
|---|---|---|---|
| No. of Cyls. & Arrangement | 6-Cylinder, V Type | ||
| Valve Mechanism | 24-Valve DOHC, Chain Drive (With Dual VVT-i) | ||
| Combustion Chamber | Pentroof Type | ||
| Flow of Intake and Exhaust Gasses | Cross-Flow | ||
| Fuel System | SFI | ||
| Ignition System | DIS | ||
| Displacement | 3956 cm3 (241.4 cu. in.) | ||
| Bore X Stroke | 94.0 X 95.0 mm (3.70 X 3.74 in.) | ||
| Compression Ratio | 10.4 : 1 | ||
| Max. Output [SAE-NET] | 202 kW@5600 rpm | ||
| Max. Torque [SAE-NET] | 381 N*m@4400 rpm | ||
| Valve Timing | Intake | Open | -11° to 29° BTDC |
| Closed | 71° to 31° ABDC | ||
| Exhaust | Open | 60° to 25° BBDC | |
| Closed | 4° to 39° ATDC | ||
| Spark Plug | Manufacturer | DENSO | |
| Type | SK20HR11 (Iridium) | ||
| Plug Gap | 1.0 - 1.1 mm (0.0394 - 0.0433 in.) | ||
| Firing Order | 1 - 2 - 3 - 4 - 5 - 6 | ||
| Research Octane Number | 95 or higher | ||
| Emission Regulation | EURO III | ||
| Engine Service Mass* (Reference) | 189.0 kg (416.7 lb) | ||
*: The figure shown is the weight of the part without coolant and oil.
MAIN FEATURES
The 1GR-FE engine has achieved the following performance through the use of the items listed in the table below.
High performance and fuel economy
Low noise and vibration
Lightweight and compact design
Good serviceability
Clean emission
| Item | (1) | (2) | (3) | (4) | (5) | |
|---|---|---|---|---|---|---|
| Engine Proper | A steel laminate type cylinder head gasket is used. | ○ | - | - | - | - |
| A taper squish shape is used for combustion chamber. | ○ | - | - | - | ○ | |
| A cylinder block sub-assembly made of aluminum alloy is used. | - | - | ○ | - | - | |
| The skirt portion of each piston has a resin coating applied to reduce friction. | ○ | ○ | - | - | ○ | |
| An oil pan sub-assembly made of aluminum alloy is used. | - | ○ | ○ | - | - | |
| Valve Mechanism | The Dual Variable Valve Timing-intelligent (Dual VVT-i) system is used. | ○ | - | - | - | ○ |
| Hydraulic valve lash adjuster assemblies are used. | ○ | ○ | - | ○ | - | |
| A timing chain sub-assembly, chain tensioner assembly (primary), and No. 2 chain tensioner assembly (secondary) are used. | - | ○ | ○ | ○ | - | |
| Roller No.1 valve rocker arm sub-assemblies are used. | ○ | - | - | - | ○ | |
| Lubrication System | An oil filter with a replaceable element is used. | - | - | - | ○ | - |
| Cooling System | Toyota Genuine Super Long Life Coolant (SLLC) is used. | - | - | - | ○ | - |
| Intake and Exhaust Systems | A cable-less type throttle body is used. | - | - | ○ | ○ | - |
| An intake air surge tank made of plastic is used. | - | - | ○ | - | - | |
| Stainless steel exhaust manifold sub-assemblies (RH and LH) are used. | - | - | ○ | - | ○ | |
| An ultra thin-wall, high-cell density ceramic type Three-Way Catalytic converter (TWC) is used. | - | - | - | - | ○ | |
| Fuel System | A fuel delivery pipe sub-assembly made of plastic is used. | - | - | ○ | - | - |
| Compact 12-hole type fuel injector assemblies are used. | ○ | - | - | - | ○ | |
| A multi-layer plastic fuel tank assembly is used. | - | - | ○ | - | ○ | |
| Quick connectors are used to connect the fuel hose with the fuel pipe. | - | - | - | ○ | - | |
| Ignition System | The Direct Ignition System (DIS) is used. | ○ | - | - | ○ | ○ |
| Long-reach type iridium-tipped spark plugs are used. | ○ | - | - | ○ | ○ | |
| Charging System | A segment conductor type generator assembly is used. | ○ | - | ○ | - | - |
| A generator clutch pulley with a one-way clutch is used. | ○ | - | - | - | ○ | |
| Starting System | Conventional reduction type starter (RA) is used. | - | - | ○ | - | - |
| Serpentine Belt Drive System | A serpentine belt drive system is used. | - | - | ○ | ○ | - |
| Engine Control System | Magnetic Resistance Element (MRE) type VVT sensors are used. | ○ | - | - | - | - |
| The Electronic Throttle Control System-intelligent (ETCS-i) is used. | ○ | - | - | - | ○ | |
| An evaporative emission control system is used. | - | - | - | - | ○ | |