Home › Engine / Hybrid System › 1GR-FE ENGINE MECHANICAL › ENGINE UNIT › 2013.08–2014.08
NM1440E _51 Engine / Hybrid System _056079 1GR-FE ENGINE MECHANICAL _0273697 ENGINE UNIT UN GENERAL/CONTROL/DETAILS F

1GR-FE ENGINE MECHANICAL  ENGINE UNIT  GENERAL/CONTROL/DETAILS  GENERAL  


OUTLINE


a.

The 1GR-FE engine is a 4.0 liter, 24 valve DOHC V6 engine. This engine uses a Dual Variable Valve Timing intelligent (Dual VVT-i) system, Direct Ignition System (DIS), and Electronic Throttle Control System intelligent (ETCS-i). These control functions achieve improved engine performance, fuel economy, and clean emissions.

W102075



SPECIFICATION


Engine Type 1GR-FE
No. of Cyls. & Arrangement 6-Cylinder, V Type
Valve Mechanism 24-Valve DOHC, Chain Drive (With Dual VVT-i)
Combustion Chamber Pentroof Type
Flow of Intake and Exhaust Gasses Cross-Flow
Fuel System SFI
Ignition System DIS
Displacement 3956 cm3 (241.4 cu. in.)
Bore X Stroke 94.0 X 95.0 mm (3.70 X 3.74 in.)
Compression Ratio 10.4 : 1
Max. Output [SAE-NET] 202 kW@5600 rpm
Max. Torque [SAE-NET] 381 N*m@4400 rpm
Valve Timing Intake Open -11° to 29° BTDC
Closed 71° to 31° ABDC
Exhaust Open 60° to 25° BBDC
Closed 4° to 39° ATDC
Spark Plug Manufacturer DENSO
Type SK16HR11 (Iridium)
Plug Gap 1.0 - 1.1 mm (0.0394 - 0.0433 in.)
Firing Order 1 - 2 - 3 - 4 - 5 - 6
Research Octane Number 95 or higher
Emission Regulation EURO IV
Engine Service Mass* (Reference) 189.0 kg (416.7 lb)

*: The figure shown is the weight of the part without coolant and oil.


W102095E02
5.542,0.271 5.813,0.438 0.271,0.167 10 false 220 5.542,0.688 5.823,0.854 0.281,0.167 10 false 200 5.542,1.115 5.823,1.281 0.281,0.167 10 false 180 5.542,1.531 5.823,1.698 0.281,0.167 10 false 160 5.542,1.958 5.802,2.125 0.26,0.167 10 false 140 5.542,2.385 5.823,2.552 0.281,0.167 10 false 120 5.542,2.823 5.802,2.99 0.26,0.167 10 false 100 5.542,3.229 5.729,3.406 0.188,0.177 10 false 80 5.542,3.656 5.74,3.823 0.198,0.167 10 false 60 5.542,4.073 5.74,4.25 0.198,0.177 10 false 40 5.542,4.5 5.76,4.667 0.219,0.167 10 false 20 5.542,4.927 5.677,5.094 0.135,0.167 10 false 0 5.552,0.052 5.792,0.229 0.24,0.177 10 false kW 5.938,2.667 6.396,2.854 0.458,0.188 10 false Output 5.271,5.302 5.542,5.479 0.271,0.177 10 false rpm 4.833,5.302 5.188,5.469 0.354,0.167 10 false 7000 4.406,5.302 4.75,5.479 0.344,0.177 10 false 6000 3.99,5.302 4.333,5.49 0.344,0.188 10 false 5000 3.552,5.302 3.927,5.479 0.375,0.177 10 false 4000 3.135,5.302 3.49,5.469 0.354,0.167 10 false 3000 2.698,5.302 3.052,5.469 0.354,0.167 10 false 2000 2.281,5.302 2.646,5.479 0.365,0.177 10 false 1000 3.302,5.552 4.208,5.729 0.906,0.177 10 false Engine Speed 1.01,1.698 1.5,1.875 0.49,0.177 10 false Torque 1.708,1.625 2,1.802 0.292,0.177 10 false 320 1.708,1.865 1.99,2.031 0.281,0.167 10 false 280 1.708,1.146 1.99,1.313 0.281,0.167 10 false 400 1.708,1.385 1.99,1.552 0.281,0.167 10 false 360 1.708,2.104 1.979,2.26 0.271,0.156 10 false 240 1.708,2.344 1.979,2.5 0.271,0.156 10 false 200 1.688,0.948 1.99,1.104 0.302,0.156 10 false N*m 0.188,0.115 1.75,0.354 1.563,0.24 12 false Performance Curve:


MAIN FEATURES


a.

The 1GR-FE engine has achieved the following performance through the use of the items listed in the table below.

i.

High performance and fuel economy


ii.

Low noise and vibration


iii.

Lightweight and compact design


iv.

Good serviceability


v.

Clean emission




Item (1) (2) (3) (4) (5)
Engine Proper A steel laminate type cylinder head gasket is used. ○ - - - -
A taper squish shape is used for combustion chamber. ○ - - - ○
A cylinder block sub-assembly made of aluminum alloy is used. - - ○ - -
The skirt portion of each piston has a resin coating applied to reduce friction. ○ ○ - - ○
An oil pan sub-assembly made of aluminum alloy is used. - ○ ○ - -
Valve Mechanism The Dual Variable Valve Timing-intelligent (Dual VVT-i) system is used. ○ - - - ○
Hydraulic valve lash adjuster assemblies are used. ○ ○ - ○ -
A timing chain sub-assembly, chain tensioner assembly (primary), and No. 2 chain tensioner assembly (secondary) are used. - ○ ○ ○ -
Roller No.1 valve rocker arm sub-assemblies are used. ○ - - - ○
Lubrication System An oil filter with a replaceable element is used. - - - ○ -
Cooling System Toyota Genuine Super Long Life Coolant (SLLC) is used. - - - ○ -
Intake and Exhaust Systems A cable-less type throttle body is used. - - ○ ○ -
An intake air surge tank made of plastic is used. - - ○ - -
Stainless steel exhaust manifold sub-assemblies (RH and LH) are used. - - ○ - ○
An ultra thin-wall, high-cell density ceramic type Three-Way Catalytic converter (TWC) is used. - - - - ○
Fuel System A fuel delivery pipe sub-assembly made of plastic is used. - - ○ - -
Compact 12-hole type fuel injector assemblies are used. ○ - - - ○
A multi-layer plastic fuel tank assembly is used. - - ○ - ○
Quick connectors are used to connect the fuel hose with the fuel pipe. - - - ○ -
Ignition System The Direct Ignition System (DIS) is used. ○ - - ○ ○
Long-reach type iridium-tipped spark plugs are used. ○ - - ○ ○
Charging System A segment conductor type generator assembly is used. ○ - ○ - -
A generator clutch pulley with a one-way clutch is used. ○ - - - ○
Starting System Conventional reduction type starter (RA) is used. - - ○ - -
Serpentine Belt Drive System A serpentine belt drive system is used. - - ○ ○ -
Engine Control System Magnetic Resistance Element (MRE) type VVT sensors are used. ○ - - - -
The Electronic Throttle Control System-intelligent (ETCS-i) is used. ○ - - - ○
An evaporative emission control system is used. - - - - ○